DFI HR908-B User manual

www.dfi.comChapter 1 Introduction
1
HR908-B
COM Express Compact Module
User’s Manual
A25420450

www.dfi.comChapter 1 Introduction
2
Copyright
This publication contains information that is protected by copyright. No part of it may be re-
produced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2014. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
COM Express Specification Reference
PICMG®COM Express ModuleTM Base Specification.
http://www.picmg.org/
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.

www.dfi.comChapter 1 Introduction
3
Table of Contents
Copyright.............................................................................................................2
Trademarks........................................................................................................2
FCC and DOC Statement on Class B.....................................................2
About this Manual..........................................................................................4
Warranty ............................................................................................................4
Static Electricity Precautions......................................................................4
Safety Measures..............................................................................................4
About the Package.........................................................................................5
Chapter 1 - Introduction.............................................................................6
Specifications ................................................................................................6
Features ........................................................................................................7
Chapter 2 - Concept.......................................................................8
COM Express Module Standards..............................................................8
Specification Comparison Table ...............................................................9
Chapter 3 - Hardware Installation.............................................. 10
Board Layout...............................................................................................10
Block Diagram.............................................................................................10
Mechanical Diagram..................................................................................11
System Memory..........................................................................................12
Installing the DIMM Module ........................................................................13
Connectors...................................................................................................14
CPU Fan Connector.....................................................................................14
COM Express Connectors ............................................................................15
COM Express connector Signal Discription....................................................16
Standby Power LED...................................................................................25
Cooling Option............................................................................................25
Installing HR908-B onto a Carrier Board............................................ 26
Chapter 4 - BIOS Setup............................................................... 28
Overview .....................................................................................................28
AMI BIOS Setup Utility.............................................................................29
Main ..........................................................................................................29
Advanced...................................................................................................29
Chipset ......................................................................................................34
Boot...........................................................................................................40
Security......................................................................................................41
Save & Exit................................................................................................41
Updating the BIOS....................................................................................42
Notice: BIOS SPI ROM.............................................................................43
Chapter 5 - Supported Software ..........................................................44
Appendix A - nLite and AHCI Installation Guide...........................57
nLite...............................................................................................................57
AHCI.............................................................................................................. 61
Appendix B - Watchdog Sample Code................................................63
Appendix C - System Error Message...................................................64
Appendix D - Troubleshooting................................................................65

www.dfi.comChapter 1 Introduction
4
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual in the CD,
insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear.
Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper instal-
lation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial damages to the
product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con-
nectors by their ends.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power
cord.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other com-
ponents. Perform the upgrade instruction procedures described at an ESD worksta-
tion only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chas-
sis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.

www.dfi.comChapter 1 Introduction
5
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• One HR908 board
• One QR (Quick Reference)
• One DVD
Optional Items
• COM331-B carrier board kit
• COM101-BAT carrier board kit
• Heat spreader: TBD
• Heat spreader with heat sink and fan: TBD
• Heat sink with fan
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance with the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.

www.dfi.comChapter 1 Introduction
6
Audio • Supports High Definition Audio interface
LAN • Intel®82579LM Gigabit Ethernet PHY
• Integrated 10/100/1000 transceiver
• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Serial ATA • Supports 4 Serial ATA interfaces
• 2 SATA 3.0 with data transfer rate up to 6Gb/s
2 SATA 2.0 with data transfer rate up to 3Gb/s
• Integrated Advanced Host Controller Interface (AHCI) controller
• Supports RAID 0/1/5/10
Watchdog
Timer • Watchdog timeout programmable via software from 1 to 255 seconds
Expansion
Interfaces • Supports 8 USB 2.0 interfaces
• Supports 1 PCIe x16 interface
- Supports Gen 3.0 (3rd generation processors)
- Configurations (supported only via a riser card):
: One x8 (GFX) and two x4 (I/O)
: Two x8 (GFX, I/O)
: One x16 (GFX, I/O)
• Supports 1 PCIe x4 and 3 PCIe x1 (default); or 7 PCIe x1 interfaces
• Supports LPC interface
• Supports SMBus interface
• Supports I2C interface
• Supports 2 serial interfaces (TX/RX)
• Supports 4-bit input and 4-bit output GPIO
Damage Free
Intelligence • Monitors CPU temperature
• Monitors CPU fan speed
• Monitors Vcore/VGFX/DDR voltages
• Watchdog timer function
OS Support • Windows XP Professional x86 & SP3 (32-bit)
• Windows XP Professional x64 & SP2 (64-bit)
• Windows 7 Ultimate x86 & SP1 (32-bit)
• Windows 7 Ultimate x64 & SP1 (64-bit)
• Windows 8 Enterprise x86 (32-bit)
• Windows 8 Enterprise x64 (64-bit)
BIOS • 64Mbit UEFI SPI BIOS
Temperature • Operating: 0oC to 60oC
• Storage: -20oC to 85oC
Humidity • 10% to 90%
Power • Input: 12V, 5VSB, VCC_RTC
PCB • Dimensions
- COM Express®Compact
- 95mm (3.74") x 95mm (3.74")
• Compliance
- PICMG COM Express®R2.1 Compact form factor, Type 6
Chapter 1 - Introduction
Specifications
Processor • 3rd generation Intel®CoreTM processors (22nm process technology)
: Intel®CoreTM i7-3615QE (6M Cache, up to 3.3GHz); 45W
: Intel®CoreTM i7-3612QE (6M Cache, up to 3.1GHz); 35W
: Intel®CoreTM i7-3555LE (4M Cache, up to 3.2GHz); 25W
: Intel®CoreTM i7-3517UE (4M Cache, up to 2.8GHz); 17W
: Intel®CoreTM i5-3610ME (3M Cache, up to 3.3GHz); 35W
: Intel®CoreTM i3-3120ME (3M Cache, 2.4GHz); 35W
: Intel®CoreTM i3-3217UE (3M Cache, 1.6GHz); 17W
: Intel®CeleronTM 1020E (2M Cache, 2.2GHz); 35W
: Intel®CeleronTM 1047UE (2M Cache, 1.4GHz); 17W
: Intel®CeleronTM 927UE (1M Cache, 1.5GHz); 17W
• 2nd generation Intel®CoreTM processors (32nm process technology)
: Intel®CoreTM i7-2715QE (6M Cache, up to 3.0GHz); 45W
: Intel®CoreTM i7-2655LE (4M Cache, up to 2.9GHz); 25W
: Intel®CoreTM i7-2610UE (4M Cache, up to 2.4GHz); 17W
: Intel®CoreTM i5-2515E (3M Cache, up to 3.2GHz); 35W
: Intel®CoreTM i3-2310E (3M Cache, 2.1GHz); 35W
: Intel®CoreTM i3-2340UE (3M Cache, 1.3GHz); 17W
: Intel®CeleronTM B810E (2M Cache, 1.6GHz); 35W
: Intel®CeleronTM 847E (2M Cache, 1.1GHz); 17W
: Intel®CeleronTM 827E (1.5M Cache, 1.4GHz); 17W
: Intel®CeleronTM 807UE (1M Cache, 1.0GHz); 10W
• BGA 1023 packaging technology
Chipset • Intel®QM67 Express chipset
System Memory • One 204-pin SODIMM socket
• Supports DDR3 SODIMM
•Supports DDR3L SODIMM
- 1066/1333MHz when operating at 1.35V
- 1066/1333/1600MHz when operating at 1.5V
• Supports up to 8GB system memory
• DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM technologies are
supported for x8 and x16 devices, unbuffered, non-ECC
Graphics • Intel®HD Graphics 4000 (3rd generation processors)
• Intel®HD Graphics 3000 (2nd generation processors)
• Intel®HD Graphics (Intel® CeleronTM processors)
• Supports LVDS, VGA, and DDI interfaces
• VGA: resolution up to 1920x1200 @ 60Hz
• LVDS: Single Channel - 18/24-bit; Dual Channel - 36/48-bit, resolution up to
1920x1200 @ 60Hz
• Digital Display Interfaces: HDMI, DVI, DP and SDVO
• HDMI, DVI, DP: resolution up to 1920x1200 @ 60Hz
• Intel®Clear Video Technology
• DirectX Video Acceleration (DXVA) for accelerating video processing
- Full AVC/VC1/MPEG2 HW Decode
• Supports DirectX 11/10.1/10/9 and OpenGL 3.0 (3rd generation processors)
• Supports DirectX 10.1/10/9 and OpenGL 3.0 (2nd generation processors)
3rd Generation Processors 2nd Generation Processors
DDR3 1066/1333/1600MHz DDR3 1066/1333MHz (i5/i3/Celeron)
DDR3 1600MHz (i7)
Chapter 1

www.dfi.comChapter 1 Introduction
7
Chapter 1
Note:
Due to the limitation of chipset QM67, 3 display features will not be supported.
Features
• Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the system at the set
time interval. If the system hangs or fails to function, it will reset at the set time interval so
that your system will continue to operate.
• DDR3
DDR3 delivers increased system bandwidth and improved performance. The advantages of
DDR3 are its higher bandwidth and its increase in performance at a lower power than DDR2.
• Graphics
The integrated Intel®HD graphics engine delivers an excellent blend of graphics performance
and features to meet business needs. It provides excellent video and 3D graphics with out-
standing graphics responsiveness. These enhancements deliver the performance and compat-
ibility needed for today’s and tomorrow’s business applications. It supports LVDS, VGA and DDI
interfaces.
• Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of
up to 3Gb/s (SATA 2.0) and 6Gb/s (SATA 3.0), it improves hard drive performance faster than
the standard parallel ATA whose data transfer rate is 100MB/s. The bandwidth of the SATA 3.0
will be limited by carrier board design.
• Gigabit LAN
The Intel 82579LM Gigabit LAN controller supports up to 1Gbps data transmission.

www.dfi.comChapter 2 Concept
8
Chapter 2
Chapter 2 - Concept
106.00
91.00
70.00
51.00
4.00
18.00
6.00
0.00
16.50 4.00 0.00
Extended
BasicCompact
Mini
74.20 80.00 91.00 121.00 151.00
Common for all Form Factors
Extended only
Basic only
Compact only
Compact and Basic only
Mini only
COM Express Module Standards
The figure below shows the dimensions of the different types of COM Express modules.
HR908-B is a COM Express Compact module. The dimension is 95mm x 95mm.

www.dfi.comChapter 2 Concept
9
Chapter 2
Specification Comparison Table
Module Pin-out - Required and Optional Features C-D Connector. PICMG®COM.0Revision 2.1
The table below shows the COM Express standard specifications and the corresponding specifications supported on the HR908-B module.
• 5 Indicates 12V-tolerant features on former VCC_12V signals.
• 6 Cells in the connected columns spanning rows provide a rough approximation of features
sharing connector pins.
Connector Feature
COM Express Module Base
Specification Type 6
(No IDE or PCI, add DDI+ USB3)
Min
/
Max
DFI HR908-B
Type 6
A-B
A-B PCI Express Lanes 0 - 5 1 / 6 6
A-B LVDS Channel A 0 / 1 1
A-B LVDS Channel B 0 / 1 1
A-B eDP on LVDS CH A pins 0 / 1 0
A-B VGA Port 0 / 1 1
A-B TV-Out NA NA
A-B DDI 0 NA NA
A-B5Serial Ports 1 - 2 0 / 2 2
A-B CAN interface on SER1 0 / 1 0
A-B SATA / SAS Ports 1 / 4 4
A-B AC’97 / HDA Digital Interface 0 / 1 1
A-B USB 2.0 Ports 4 / 8 8
A-B USB Client 0 / 1 0
A-B USB 3.0 Ports NA NA
A-B LAN Port 0 1 / 1 1
A-B Express Card Support 1 / 2 2
A-B LPC Bus 1 / 1 1
A-B SPI 1 / 2 1
A-B SDIO (muxed on GPIO) 0 / 1 0
General Purpose I/O 8 / 8 8
A-B SMBus 1 / 1 1
A-B I2C 1 / 1 1
A-B Watchdog Timer 0 / 1 1
A-B Speaker Out 1 / 1 1
A-B External BIOS ROM Support 0 / 2 0
A-B Reset Functions 1 / 1 1
A-B6
System I/O
System Management
Connector Feature
COM Express Module Base
Specification Type 6
(No IDE or PCI, add DDI+ USB3)
Min
/
Max
DFI HR908-B
Type 6
A-B
A-B Thermal Protection 0 / 1 1
A-B Battery Low Alarm 0 / 1 1
A-B Suspend/Wake Signals 0 / 3 2
A-B Power Button Support 1 / 1 1
A-B Power Good 1 / 1 1
A-B VCC_5V_SBY Contacts 4 / 4 4
A-B5Sleep Input 0 / 1 1
A-B5Lid Input 0 / 1 1
A-B5Fan Control Signals 0 / 2 2
A-B Trusted Platform Modules 0 / 1 0
A-B
A-B VCC_12V Contacts 12 / 12 12
Power Management
Power
Connector Feature
COM Express Module Base
Specification Type 6
(No IDE or PCI, add DDI+ USB3)
Min
/
Max
DFI HR908-B
Type 6
C-D PCI Express Lanes 16 - 31 0 / 16 0
PCI Express Graphics (PEG) 0 / 1 1
Muxed SDVO Channels 1 - 2 NA NA
PCI Express Lanes 6 - 15 0 / 2 2
PCI Bus - 32 Bit NA NA
PATA Port NA NA
LAN Ports 1 - 2 NA NA
DDIs 1 - 3 0 / 3 3
USB 3.0 Ports 0 / 4 N
A
C-D
C-D VCC_12V Contacts 12 / 12 12
Power
C-D6
C-D6
System I/O

www.dfi.comChapter 3 Hardware Installation
10
Chapter 3
Chapter 3 - Hardware Installation
Board Layout
Top View
Bottom View
Block Diagram
COM Express connector
C1
D1
C110
D110
B1
B110
A1
A110
COM Express connector
IMVP7
(Vcore,Vgfx)
PEG 16x LANES
PCIe x1 6x
CRT
USB 2.0 8x
SATA 2.0 2x, SATA 3.0 2x
LVDS (Dual Channel)
Channel A (DDR3)
1066/1333/1600MHz
Channel A (DDR3L)
1066/1333MHz
z
3rd/2nd Generation
Intel®Core™ i7/i5/i3
CORE Processor
CORE CORE CORE
Graphics
CORE Memory
Controller
DMI
(Direct Media
Interface)
Intel®FDI
(Flexible Display
Interface)
106
DDR3/
DDR3L
SODIMM
Mobile Intel®QM67
(Platform
Controller Hub)
SM Bus
HD Audio
LPC Bus
Intel®GLAN
PHY 82579LM
LAN Ports
A / B
C / D
PEG
16x
LANES
HD
Audio
LPC Bus
USB
2
.
0
8x
S
20
2
S
3
02
SATA
2
.
0
2x
,
SATA
3
.
0
2x
LVDS (D l Ch l)
CRT
LVDS
(Dual
Channel)
PCI 1
6
CRT
PCIe
x1
6x
LAN
Ports
PCIe x1, Lane 8
SM
Bus
HD A
di
DDP Port C
PCIe x1 Lane 7
Serial Port 2x
Seri
al P
ort
2x
LPC
Bus
GPIO/
WDT/I2C
SPI
Si
lP
t
2
SPI
System Fan PWM/TACH_IN
System
Fan
PWM/TACH
_
IN
DDP
Port
C
DDP Port D
DDP
Port
D
DDP Port B/SDVO Port B
DDP
Port
B/SDVO
Port
B
PCIe
x1
Lane
7
DDR3 SODIMM
iTE
IT8518E
Intel
QM67
1
CPU fan
Intel 82579LM
SPI Flash
BIOS
Standby Power LED
BGA 1023
i3/i5/i7
Intel