DFI LanParty UT RDX200 series User manual

System Board
User’s Manual
935-D200C1-000G
87730551

Copyright
This publication contains information that is protected by copyright.
No part of it may be reproduced in any form or by any means or
used to make any transformation/adaptation without the prior
written permission from the copyright holders.
This publication is provided for informational purposes only. The
manufacturer makes no representations or warranties with respect to
the contents or use of this manual and specifically disclaims any
express or implied warranties of merchantability or fitness for any
particular purpose.The user will assume the entire risk of the use or
the results of the use of this document. Further, the manufacturer
reserves the right to revise this publication and make changes to its
contents at any time, without obligation to notify any person or
entity of such revisions or changes.
© 2005. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for
identification purpose only and are the properties of the respective
owners.

FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for
help.
Notice:
1. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
2. Shielded interface cables must be used in order to comply with
the emission limits.

Table of Contents
About this Manual................................................................................
Warranty.....................................................................................................
Static Electricity Precaution................................................................
Safety Measures.....................................................................................
About the Package...............................................................................
Before Using the System Board.........................................................
Français....................................................................................................
Deutsch....................................................................................................
Español....................................................................................................
Ðóññêèé ÿçûê............................................................................................
Chapter 1 - Introduction....................................................................
Specifications...................................................................................................................................
Special Features of the System Board..................................................................
Chapter 2 - Hardware Installation....................................................
System Board Layout ..........................................................................................................
System Memory..........................................................................................................................
CPU.......................................................................................................................................................
Jumper Settings............................................................................................................................
Rear Panel I/O Ports.............................................................................................................
I/O Connectors..........................................................................................................................
ATI CrossFire Technology....................................................................................................
Chapter 3 - BIOS Setup......................................................................
Award BIOS Setup Utility.................................................................................................
ATI RAID BIOS..........................................................................................................................
Sil3114 SataRAID BIOS.....................................................................................................
Updating the BIOS..................................................................................................................
Chapter 4 - Supported Softwares.....................................................
Drivers, Utilities and Software Applications......................................................
Installation Notes.......................................................................................................................
Appendix A - System Error Messages...............................................
Appendix B - Troubleshooting..........................................................
5
5
6
6
7
7
8
10
12
14
16
16
20
26
26
27
31
37
43
54
73
81
81
128
128
129
131
131
149
150
152

About this Manual
This user’s manual contains detailed information about the system
board. If, in some cases, some information doesn’t match those
shown in the multilingual manual, the multilingual manual should al-
ways be regarded as the most updated version. The multilingual
manual is included in the system board package.
To view the user’s manual, insert the CD into a CD-ROM drive.The
autorun screen (Mainboard Utility CD) will appear. Click the
“TOOLS” icon then click “Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from
misuse of the product, inability to use the product, unauthorized
replacement or alteration of components and product
specifications.
2. The warranty is void if the product has been subjected to
physical abuse, improper installation, modification, accidents or
unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may
not, under any circumstances, attempt to perform service,
adjustments or repairs on the product, whether in or out of
warranty. It must be returned to the purchase point, factory or
authorized service agency for all such work.
4. We will not be liable for any indirect, special, incidental or
consequencial damages to the product that has been modified
or altered.

Introduction
1
6
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board,
components or devices even before installing them in your system
unit. Static electrical discharge can damage computer components
without causing any signs of physical damage. You must take extra
care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its
anti-static bag until you are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of
the components, contacts or connections.
5. Avoid touching the pins or contacts on all modules and
connectors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk
drive and other components. Perform the upgrade instruction
procedures described at an ESD workstation only. If such a
station is not available, you can provide some ESD protection
by wearing an antistatic wrist strap and attaching it to a metal
part of the system chassis. If a wrist strap is unavailable,
establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.....
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis
cover for installation or servicing. After installation or servicing,
cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by
the manufacturer.
• Dispose of used batteries according to the battery
manufacturer’s instructions.

1
Introduction
7
About the Package
The system board package contains the following items. If any of
these items are missing or damaged, please contact your dealer or
sales representative for assistance.
;One system board
;One Karajan audio module
;Two IDE round cables
;One floppy round cable
;Four Serial ATA data cables
;Two Serial ATA power cables
;One I/O shield
;One SATA driver diskette (for ATI SB450 and Silicon Image Sil
3114 RAID)
;One “Mainboard Utility” CD
;One user’s manual
;One Quick Installation Guide
The system board and accessories in the package may not come
similar to the information listed above.This may differ in accordance
to the sales region or models in which it was sold. For more
information about the standard package in your region, please
contact your dealer or sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need
at least the following internal components.
•A CPU
•Memory module
•Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use
which will normally include at least a keyboard, a mouse and a video
display monitor.

Introduction
1
8
Français
Caractéristiques et Spécifications
Processeur
• AMD AthlonTM 64 FX / AthlonTM 64 / SempronTM
• Interface HyperTransport 2000MT/s
• Socket 939
Chipset
• ATI chipset
- Pont nord: ATI Radeon®Xpress 200 CrossFire
- Pont sud: ATI SB450
Mémoire Système
• 4 sockets DDR SDRAM DIMM 184 broches
• Supporte l’interface de mémoire deux canaux (128-bit)
• Supporte jusqu’à 4GB de mémoire
• Supporte DDR SDRAM DIMM PC2100 (DDR266), PC2700 (DDR333) et
PC3200 (DDR400)
• Supporte exclusivement les modules DIMM non-ECC x8/x16, densité de
RAM jusqu’à 512Mb, DIMM non-tamponnés
Logements d’Extension
• 2 slots PCI Express x16
Mode CrossFire - Chaque slot x16 fonctionne à la bande passante x8.
Mode Single VGA - Le slot PCIE1 fonctionne à la bande passante x16. Le
slot PCIE3 fonctionne à la bande passante x1.
• 1 slot PCI Express x1
• 3 slots PCI
BIOS
• Compatible avec Award BIOS
• CMOS Reloaded
• Overclocking de CPU/DRAM
• Contrôle du voltage de CPU/DRAM/Chipset
• Mémoire Flash 4Mbit
Design à Haut Rendement Énergétique
• ACPI STR (Suspend to RAM) fonction
• Réveil-Sur-PS/2 Clavier/Souris
• Réveil-Sur-USB Clavier/Souris
• Eveil Sonnerie
• Réveil Par Le Réseau
• Minuterie RTC pour allumer le système
• Récupération après Défaillance d’Alimentation CA
System Health Monitor Fonctions
• Gère l’alarme de température et de surchauffe de CPU/système/chipset
• Gère l’alarme de voltage et d’échec de 12V/5V/3.3V/Vcore/Vbat/5Vsb/
Vchipset/Vdram
• Gère la vitesse de ventilateur du ventilateur de CPU/Fan2/Fan3
• Protection du CPU - supporte la mise hors circuit automatique en cas de
surchauffage du système
Caractéristiques Audio sur Carte
• Karajan carte audio
- CODEC Realtek ALC882 8-canaux
- 6 prises audio, 1 connecteur CD-in et 1 connecteur audio de l’avant

1
Introduction
9
• Sorties de niveau de lignes stéréo vraies
• Interface entrée/sortie S/PDIF
Fonctionnalités Onboard LAN
• Deux Gigabit LAN - Marvell 88E8053 PCI Express et Marvell 88E8001 PCI
LAN
• Supporte IEEE 802.3 (10BASE-T), 802.3u (100BASE-TX) et 802.3ab
(1000BASE-T)
• Fonctions de gestion d’alimentation intégrées
• Support câble pour la gestion
Interface IDE
• Supporte des disques durs jusqu’à UltraDMA 133Mbps
Interface Série ATA avec RAID
• Quatre ports de série ATA gérés avec la puce ATI SB450 (pour les
LANPARTY UT RDX200 CF-D uniquement)
- Vitesse SATA jusqu’à 1.5Gb/s
- RAID 0 et RAID 1
• Quatre ports de série ATA gérés par Silicon Image Sil 3114 (pour les
LANPARTY UT RDX200 CF-DR uniquement)
- Vitesse SATA jusqu’à 1.5Gb/s
- RAID 0, RAID 1, RAID 0+1 et RAID 5
Interface IEEE 1394
• VIA VT6307
• Supporte 2 ports 100/200/400 Mb/séc
Le Panneau des Ports Entrée/Sortie en Arrière
• 1 port souris PS/2 et 1 port clavier PS/2
• 2 S/PDIF RCA prises (S/PDIF-in et S/PDIF-out)
• 1 carte Karajan (6 prises audio)
• 1 port IEEE 1394
• 2 ports RJ45 LAN
• 6 ports USB 2.0/1.1
Connecteurs Entrée/Sortie
•1 connecteur pour 2 ports USB 2.0/1.1 supplémentaires
• 1 connecteur pour 1 IEEE 1394
• 1 connecteur pour 1 série
• 1 connecteur pour module audio Karajan
• 1 connecteur audio frontal pour les jacks de sortie externe et d’entrée
micro (sur le module audio Karajan)
•1
connecteur CD-in audio internes (sur le module audio Karajan)
• 1 S/PDIF l’assemblage pour l’adjonction de câble optique
• 1 connecteur IR et 1 connecteur CIR
•8
connecteurs Serial ATA (pour les modèles LANPARTY UT RDX200 CF-
DR uniquement)
4 connecteurs Serial ATA (pour les LANPARTY UT RDX200 CF-D
uniquement)
• 2 connecteurs IDE et 1 connecteur de 90o FDD
• 1 connecteur d’alimentation 24-pin ATX
• 1 connecteur d’alimentation 8-pin 12V ATX
• 1 prises d’alimentation 4-broches 5V/12V (type-FDD)
• 1 connecteur devant panneau
• 5 connecteurs de ventilateurs
• 4 indicateurs diagnostiques
• EZ interrupteurs (bouton de power et reset)
PCB
• ATX, 24cm (9.45") x 30.5cm (12")

Introduction
1
10
Deutsch
Leistungsmerkmale und Technische Daten
Prozessor
• AMD AthlonTM 64 FX / AthlonTM 64 / SempronTM
• Interface HyperTransport 2000MT/s
• Socket 939
Chipset
• ATI chipset
- Nordbrücke: ATI Radeon®Xpress 200 CrossFire
- Südbrücke: ATI SB450
Systemspeicher
• 4 DDR-SDRAM-DIMM- Fassungen mit 184poligem Anschlußstecker
• Unterhält 128-bit – Speiher mit den zwei Kanälen
• Unterhält bis zum 4GB-Systemspeicher
• Unterstützt DDR SDRAM DIMM PC2100 (DDR266), PC2700 (DDR333)
und PC3200 (DDR400)
• Unterhält nur non-ECC x8/x16 DIMMs, ohne Dämpfer, bis zum 512Mb
DRAM
Erweiterungssteckfasssungen
• 2 PCI Express x16 Steckplätze
CrossFire Modus - Beide x16 Steckplätze arbeiten mit x8 Bandbreite.
Single VGA Modus – Der PCIE1 Steckplatz arbeitet mit x16 Bandbreite und
der PCIE3 Steckplatz arbeitet mit x1 Bandbreite.
• 1 PCI Express x1 Steckplätze
• 3 PCI-Einbauplätzen
BIOS
• Kompatibilität mit Award BIOS
• CMOS Reloaded
• Die Frequenzerhöhung CPU/DRAM
• Die Spannungserhöhung CPU/DRAM/Chipset
• Flash-Speicher (4Mbit)
Energomisches Design
• ACPI STR (Suspend to RAM) funktion
• Wecken bei Betätigung PS/2 Tastatur/Maus
• Wecken bei USB-Tastatur/Maus
• Wecken bei Klingeln und Wecken des Systems durch das Netzwerk
• RTC-Taktgeber zum Einschalten des Systems
• Wiederherstellung der Wechselstromversorgung nach einem Ausfall
System Health Monitor Funktions
• Überwachung der Temperatur des CPU/System/Chipset sowie Warnsignal bei
Überhitzung
• Überwachung der Spannungen des 12V/5V/3.3V/Vcore/Vbat/5Vsb/Vchipset/
Vdram
• Überwachung der Geschwindigkeit des CPU-, Fan 2 und Fan 3-Ventilators
• Prozessor-Shutz - Die Ausschaltung bei der Überhitzung – die automatische
Ausschaltung des Computers bei der Überhitzung
Audiomerkmale auf Platine
• Karajan-platine
- Realtek ALC882 8-Kanal-Codec