Dialogic BorderNet 2020 Instruction Manual

1
Dialogic®BorderNet™ 2020 Integrated Multimedia
Gateway Quick Start Installation Guide
This document provides a high-level overview of how to connect power and network cabling
for the BorderNet 2020 IMG. For detailed information about installation and setup, refer to
the online documentation at http://www.dialogic.com/manuals/bordernet2020img1.0/default.htm.
Before you begin, review the packing list to verify that you received all items listed. If there
are any discrepancies, contact your Dialogic representative.
Locating the Base MAC Address
The base MAC address is printed on the identification label located on the underside rear of
the 2020 IMG. The base MAC address is assigned to the CTRL ports. The other MAC
addresses are under software control.
Use this base MAC address when configuring the IP address. Because of its location, we
recommend that you obtain the base MAC address before you install the system. The
identification label is similar to this example:
Connecting AC power
AC power modules must be plugged into three-prong grounded outlets. Do not use the
external grounding points on the rear of an AC 2020 IMG to ground the system. These
grounding points are for DC system grounding only.
AC input power:
100 - 240 V AC, 60 - 50 Hz, 2 A - 1 A
115 V AC @ 2 A, or 230 V AC @ 1 A
Redundant, hot-swappable AC power modules are located at the rear of the docking station.
Note: When connecting a second power supply, you do not need to turn off power to the
primary AC power module.
Connecting DC power
You must connect the DC 2020 IMG to earth ground before connecting power. To connect a
ground to the DC 2020 IMG, use 10, 12, or 14 AWG machine tool wire (MTW) (green/yellow
for earth ground). Dialogic supplies a two-hole #10 solderless crimp grounding lug that is
attached to the grounding screws on the rear of the 2020 IMG.
Caution: Do not daisy-chain two or more systems. Do not wire the 2020 IMG directly to
other equipment or to a common bus bar.
DC input power:
-40 to -60 V DC (-48 V DC nominal) @ 6 A
Redundant, hot-swappable DC power modules are located at the rear of the docking station.
Warning! You must connect the 2020 IMG to a true earth ground to maintain
signaling integrity and to prevent electrical shock. Do not connect ground to -48 V.

Dialogic® BorderNet™ 2020 Integrated Multimedia Gateway Quick Start Installation Guide
2
Connecting to a Single DC Power Source
To connect a single external DC power source to the 2020 IMG:
1. Turn OFF the existing external power source and disconnect it from the power
supply.
Warning! Failure to turn the power OFF at the source may result in electrical
shock.
2. Attach the wires from the external power source to the DC power module plug.
3. Insert the plug into the DC power module.
4. Reconnect the external power source and turn the power ON.
5. Press the ON button on the front of the server.
Connecting to a Redundant DC Power Source
To connect a redundant DC power source to the 2020 IMG, follow the Connecting to a Single
Power Source procedure.
Note: Do not turn off power to the primary -48 V DC module or the unit will shut down.
DC power cables
A 500 mm DC power pigtail cable is included with DC systems. If you require a longer cable,
the 4 m cable is available for order (P/N BDN-CBL-1000).
Caution: The color specifications for the DC power cables are not identical. Be sure to
review the specifications that are shipped with your cable before installation.
DC power cable (500 mm)
DC power pigtail 4 m cable (P/N BDN-CBL-1000)

Dialogic® BorderNet™ 2020 Integrated Multimedia Gateway Quick Start Installation Guide
3
Connecting to the Network
Complete the following steps to connect the 2020 IMG to the network:
1. Access the Dialogic®BorderNet™ 2020 Integrated Multimedia Gateway WebHelp at
http://www.dialogic.com/webhelp/BorderNet2020/1.0.0/WebHelp/default.htm.
2. Refer to the Installing the Software section in the Dialogic®BorderNet™ 2020
Integrated Multimedia Gateway WebHelp.
3. Review the options for installing the software and choose the appropriate installation
method for your site.
4. Install the software.
5. Follow the instructions for configuring the IP address and setting the system software
file name as described in the Dialogic®BorderNet™ 2020 Integrated Multimedia
Gateway WebHelp.
6. Using a shielded Ethernet cable, connect CTRL 0 or CTRL 1 to your network Ethernet
switch. Use the CTRL Ethernet connectors on the rear of the 2020 IMG for network
management.
Depending on the configuration, the binary downloads from either an SD card or from an
FTP server that you configured. Once the binary downloads, you can begin the configuration
as described in the Dialogic®BorderNet™ 2020 Integrated Multimedia Gateway WebHelp.
You will connect the remaining cables as you configure the system.
Document P/N: 64-1103-02