Diamondback 510Ic User manual

510Ic Owner’s Manual
1
CONSOLE OVERVIEW & GENERAL NOTES
A primary feature of the 510Ic is the ability to control and monitor the user’s workout program via the brilliant LCD console. At any time, the user
may view their speed, RPM, elapsed time, distance, calories and pulse rate.
To provide power to the display console and computer, begin pedaling at a rate exceeding fifteen (15) revolutions per minute. The 510Ic Indoor
Cycle uses an on-board generator to supply power to the computer, console display and resistance control system while the unit is in use. While
the unit generates power for the current functions, a set of batteries is also charged to allow console operation for up to sixty (60) seconds without
pedaling. Should the battery ever run down or if the console does not light, connect the included power supply/adaptor to a 120V power source.
Plug the opposite end into the 510Ic power input jack found near the ground at the rear of the machine. Begin pedaling to recharge the battery.
To avoid damage and danger, use only the power supply/adaptor that was designed for the 510Ic. To maintain and extend the life of the battery, it
is necessary to charge the battery overnight, once per week.
To conserve energy, the console will automatically power down after sixty (60) seconds of inactivity.
CONSOLE KEYPAD FUNTION
Fit Test Key.
Test heart rate recovery status.
Reset Key.
Press and hold for 2 seconds, computer will
reboot from user setting. Return to main menu
during preset workout value or stop mode.
Up & Down Arrow Keys.
Increase and decrease resistance level.
Setting selection
Mode / Enter.
Confirm setting or selection.
Start-Stop Key.
Start or Stop workout.

2
CONSOLE LCD DISPLAY
Time: Count up – No preset target, Time will count up from 00:00 to maximum
99:59. Each increment is 1 minute. Count down – If training with preset Time, Time
will count down from preset to 00:00. Each preset increment is 1 minute between
00:00 to 99:00.
Speed: Displays current training
speed. Maximum speed is 99.9
KM/H or MPH.
RPM: Displays the Rotation Per
Minute. Display range 0~15~999
Distance: Accumulates total distance from 0.00 up to 99.99 KM or Miles. The user
may preset target distance data by using UP/DOWN button. Each preset increment
is 0.1KM or Mile between 0.00 to 99.90.
Calories: Tracks calorie consumption during training from 0 to maximum 9999
calories. (This data is a rough guide for comparison of dierent exercise sessions
and should not be used in medical treatment.)
Pulse: User may set up target
pulse from 0 – 30 to 230; and
computer buzzer will beep
when actual heart rate is over
the target value during workout.

510Ic Owner’s Manual
3
CONSOLE OPERATION
POWER ON.
Plug in power supply, computer will power on and display all segments
on LCD for 2 seconds.
WORKOUT SELECTION.
Use UP or DOWN (Encoder) to select workout.
Manual Beginner Advance
Cardio Sporty

4
2. Use UP or DOWN
(Encoder) to set TIME,
DISTANCE, CALORIES,
PULSE and press
MODE / ENTER to
confirm.
4. Press START/STOP keys to pause workout. Press RESET to return to main menu.
MANUAL MODE. Press START in main menu to start workout in manual mode.
1. Use UP or DOWN
(Encoder) to select
workout program,
choose Manual
and press MODE /
ENTER.
3. Press START/
STOP keys to start
workout. Use UP
or DOWN (Encoder)
to adjust load level.

510Ic Owner’s Manual
5
2. Use UP or DOWN
(Encoder) to select
Beginner program
1~4 and press
MODE / ENTER.
2. Use UP or DOWN
(Encoder) to select
Advance program
1~4 and press
MODE / ENTER.
BEGINNER MODE. Four program selection. ADVANCE MODE. Four program selection.
1. Use UP or
DOWN (Encoder)
to select workout
program, choose
Beginner and
press MODE /
ENTER.
1. Use UP or
DOWN (Encoder)
to select workout
program, choose
Advance and
press MODE /
ENTER.
3. Use UP or DOWN (Encoder) to set TIME.
4. Press START/STOP key to start workout. Use UP or DOWN
(Encoder) to adjust load level.
5. Press START/STOP key to pause workout. Use RESET to return to
main menu.
3. Use UP or DOWN (Encoder) to set TIME.
4. Press START/STOP key to start workout. Use UP or DOWN
(Encoder) to adjust load level.
5. Press START/STOP key to pause workout. Use RESET to return to
main menu.

6
2. Use UP or DOWN
(Encoder) to select
Sporty program 1~4
and press MODE /
ENTER.
2. Use UP or DOWN
(Encoder) to select
Age.
3. Use UP or
DOWN (Encoder)
to select 55%,
75%, 90% or
TAG (Target H.R.)
(default 100).
SPORTY MODE. Four program selection. CARDIO MODE. Target Heart Rate Training Mode.
1. Use UP or
DOWN (Encoder)
to select workout
program, choose
Sporty and press
MODE / ENTER.
1. Use UP or
DOWN (Encoder)
to select workout
program, choose
Cardio and press
MODE / ENTER.
3. Use UP or DOWN (Encoder) to set TIME.
4. Press START/STOP key to start workout. Use UP or DOWN
(Encoder) to adjust load level.
5. Press START/STOP key to pause workout. Use RESET to return to
main menu.
4. Press START/
STOP key to start
workout. Use UP
or DOWN (Encoder)
to adjust load level.
5. Press START/
STOP key to pause
workout. Use
RESET to return to
main menu.

510Ic Owner’s Manual
7
At the end of your workout use hand grips or wireless chest strap
and press FIT TEST key.
All function display will stop
except “TIME” and will count
down from 00:60 to 00:00
Screen will display your heart
rate recovery status with the F1,
F2…. to F6. F1 is the best, F6 is
the worst.
Keep exercising to improve your heart rate recovery status.
Press the FIT TEST button again to return the main display.
FIT TEST.