digi-tech JAMMAN - MANUAL 2 User manual

Warranty
We at DigiTech are very proud of our products and back up each one we sell
with the following warranty:
1.The warranty registration card must be mailed within ten days after
purchase date to validate this warranty.
2. DigiTech warrants this product, when used solely within the U.S., to be
free from defects in materials and workmanship under normal use and
service.
3. DigiTech liability under this warranty is limited to repairing or replacing
defective materials that show evidence of defect, provided the product
is returned to DigiTech WITH RETURN AUTHORIZATION, where all
parts and labor will be covered up to a period of one year.A Return
Authorization number may be obtained from DigiTech by telephone.
The company shall not be liable for any consequential damage as a
result of the product’s use in any circuit or assembly.
4. Proof-of-purchase is considered to be the burden of the consumer.
5. DigiTech reserves the right to make changes in design, or make additions
to, or improvements upon this product without incurring any obligation
to install the same on products previously manufactured.
6.The consumer forfeits the benefits of this warranty if the product’s main
assembly is opened and tampered with by anyone other than a certified
DigiTech technician or, if the product is used with AC voltages outside
of the range suggested by the manufacturer.
7.The foregoing is in lieu of all other warranties, expressed or implied,
and DigiTech neither assumes nor authorizes any person to assume any
obligation or liability in connection with the sale of this product. In no
event shall DigiTech or its dealers be liable for special or consequential
damages or from any delay in the performance of this warranty due to
causes beyond their control.
NOTE: The information contained in this manual is subject to change at any
time without notification. Some information contained in this manual may
also be inaccurate due to undocumented changes in the product or operating
system since this version of the manual was completed.The information
contained in this version of the owner’s manual supersedes all previous
versions.

DECLARATION OF
CONFORMITY
Manufacturer’s Name: DigiTech
Manufacturer’s Address: 8760 S. Sandy Pkwy.
Sandy, UT 84070, USA
Declares that the product:
Product name: Control 2
Note: Product name may be suffixed by the letters-EU.
Product option: None
Conforms to the following Product Specifications:
Safety: IEC 60065 (7th ed. 2001)
EMC: EN 55013 (2001 + A1)
EN 55020 (1998)
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage
Directive 73/23/EEC and the EMC Directive 89/336/EEC as amended by
Directive 93/68/EEC.
Vice-President of Engineering-MI
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Date: November 20, 2007
European Contact: Your local Digitech Sales and Service Office or
Harman Music Group
8760 S. Sandy Pkwy.
Sandy, UT
84070 USA
Ph: [phone]
Fax: [phone]
IMPORTANT! PLEASE READ
Only connect the Control 2 Remote Foot Controller to the
GSP1101 or other DigiTech products which specify a connection
to the Control 2. Do not connect the Control 2 Remote Foot
Controller to Ethernet connections as damage will occur.

Contents
Introduction............................................................................. 1
Checking your GSP1101 Software Version.................................. 1
Top Panel.................................................................................. 2
Using the Control 2 Remote Foot Controller..................... 5
Modes............................................................................................... 5
5 Patch Mode......................................................................................................5
10 Patch Mode ...................................................................................................5
Switching Between 5 Patch and 10 Patch Modes....................... 5
Selecting Banks............................................................................... 6
Selecting Presets ............................................................................ 7
Bypassing Presets ........................................................................... 7
Turning Effects On or Off.............................................................. 7
Bounce Back ................................................................................... 8
Volume Update............................................................................... 9
MIDI CC Send................................................................................. 9
Expression Pedal Calibration ........................................................ 10
Tuner................................................................................................ 11
Assigning Parameters to the CONTROL Footswitch (#10) ..... 11
Assigning Parameters to the Expression Pedals......................... 12

Introduction
Congratulations and thank you for purchasing the Control 2 Remote Foot
Controller! The Control 2 will help you get the most out of your GSP, giving
you hands-free access to all the tones and effects your GSP has to offer.
Please take a moment to make sure you have everything that’s included with
your Control 2 Remote Foot Controller purchase:
Control 2 Remote Foot Controller
Controller Cable
The Control 2 Remote Foot Controller is extremely easy to use, but we
recommend reading this brief manual to familiarize yourself with the Control
2’s many features.
Checking your GSP1101 Software Version
If you’re using the Control 2 with a GSP1101, the GSP1101 software must be
version 2.0 or later.
To check your GSP1101 software version, follow these steps:
From the GSP preset screen, press the Edit/Select knob once to access
the menu navigation system.
Turn the Edit/Select knob until the Version option is highlighted.The
software version number is shown next to the Version option.
If the version number is 2.0 or greater, your GSP1101 is ready to use
with your Control 2. If the version number is less than 2.0 (1.2, for
example), you must update your GSP1101. Go to www.digitech.com for
instructions on how to update your GSP1101.
•
•
1.
2.
3.
Introduction

Control 2 Owner’s Manual

Top Panel
1 2 3 4
5
6
78
9
Bank Down / Bank Up
Press either of these footswitches to scroll through banks (groups) of Factory and
User presets. When either of these footswitches are pressed, the Display shows
the presets contained in each bank, and the preset footswitches will flash (1-5
in 5 Patch mode and 1-10 in 10 Patch mode). Press a footswitch with a flashing
LED to select a preset in the bank. If no preset is selected after 5 seconds (or if a
footswitch with an unlit LED is pressed), you are returned to your current preset.
Display
Displays bank names, preset names, effect on/off status, tuner information, and
expression pedal calibration information.
Factory LED
Lights when a Factory preset or bank is selected.
Wah LED
Lights when the Wah effect is activated.
Expression Pedal
The built-in Expression Pedal provides real time control over parameters in your
presets.You can assign the Expression Pedal to almost any parameter, giving you
the option to control how fast a Chorus or Rotary effect oscillates, how much gain
your amp model has, how loud the delays are, and many more. See page 11 for
more information about how to assign parameters to the Expression Pedal. Refer
to your GSP owner’s manual for a list of available presets.
1.
2.
3.
4.
5.
Top Panel
2Control 2 Owner’s Manual

The Expression Pedal can alternatively turn on and control the Wah effect by
pressing down firmly on the toe switch (this disables control of other parameters
assigned to the Expression Pedal). Press down firmly on the toe switch again
to turn off the Wah effect and switch the pedal back to controlling the saved
expression parameters.
NOTE: Rock the Expression Pedal all the way forward and all the way back each
time you power up the Control 2.
Tuner
The TUNER footswitch enables and disables the tuning function in the connected
GSP. The TUNER footswitch LED lights when the Tuner is active.
When the tuner is activated, the Display briefly reads TUNER. To begin tuning, play
a note on your guitar (a harmonic at the 12th fret usually works best).The note
being played appears in the Display, and arrows indicates whether the note is sharp
or flat. An arrow pointing to the left ( ) indicates the note is sharp and should be
tuned down. An arrow pointing to the right ( ) indicates the note is flat and
should be tuned up.When your note is in tune, is displayed.
Tempo
Press the TEMPO footswitch 2 or more times to set the time of the current
preset’s Delay effect. The TEMPO LED flashes to indicate the delay time. The
Delay effect does not need to be active to set the delay time.
Footswitches 1-5
These footswitches are used to select presets in the active bank. The LED
adjacent to each footswitch lights to indicate which preset is selected.
Footswitches 6-10
These footswitches are used for turning effects on and off (5 Patch Mode) or for
selecting the second group of 5 presets in the active bank (10 Patch Mode). In 5
Patch Mode, Footswitches 6-10 act as effects on/off switches for the effect labeled
above each footswitch. When an effect is turned on or off, the LED adjacent to its
footswitch will light or darken to indicate the effect’s on/off status.The number 10
footswitch is labeled CONTROL, and can be assigned a preset-specific parameter
(min/max setting or effect on/off). See page 11 for more information about
assigning parameters to the CONTROL Footswitch.
In 10 Patch Mode, each preset bank has ten presets to select from so each
numbered footswitch 1-10 will select a preset. The LED adjacent to the
footswitch will light to indicate which preset is selected. Only one of the ten
numbered footswitches can be lit at a time in 10 Patch Mode. See page 5 for more
information about 5 Patch Mode and 10 Patch Mode.
6.
7.
8.
9.
Top Panel

Control 2 Owner’s Manual

Rear Panel
12
Processor Jack
Attach one end of the included Controller cable here. Connect the other
end to your GSP unit’s Foot Controller port.
WARNING: Only connect the Control 2 Remote Foot Controller to
the GSP1101 or other DigiTech products which specify a connection to
the Control 2. Do not connect the Control 2 Remote Foot Controller
to Ethernet connections as damage will occur.
Expression 2 Input
Connect an optional expression pedal here using a 1/4” cable. A passive
expression controller or volume pedal is recommended.
1.
2.
Rear Panel
Control 2 Owner’s Manual

Using the Control 2 Remote Foot Controller
Modes
The Control 2 operates in one of two modes: 5 Patch Mode or 10 Patch
Mode.
5 Patch Mode
In 5 Patch Mode, the footswitches numbered 1-5 each select a preset (also
known as a “patch”) in the selected bank.There are 20 banks to select from
(you can change banks using the Bank Down/Bank Up footswitches). The
lit footswitch (1-5) indicates the current preset selected in the bank; only one
of the 1-5 footswitches can be lit at a given time. From the factory, 5 Patch
Mode is the default mode.
Also in 5 Patch Mode, Footswitches 6-9 each turn an effect on or off. You
can also configure the CONTROL Footswitch to turn an effect on or off, or
toggle a parameter between two values (for example, the Delay level can be
switched from 20 to 40 and back). Refer to page 9 for instructions on how to
configure The CONTROL Footswitch.
10 Patch Mode
In 10 Patch Mode, Footswitches 1-10 each select a preset in the selected
bank.There are 10 banks to select from. The lit footswitch indicates the
current preset selected in the bank; only one of the 1-10 footswitches can be
lit at any given time.
Switching Between 5 Patch and 10 Patch Modes
To change the mode, follow these steps:
From the GSP preset screen, press the Edit/Select knob once to enter
the menu navigation system.
Turn the Edit/Select knob until the Foot Controller menu is highlighted
and press the knob again.
In the Foot Controller menu, make sure Switch Mode is highlighted and
press the Edit/Select knob to select 5 Patch or 10 Patch mode.
Press the Back button to save this setting.
1.
2.
3.
4.
Using the Control 2 Remote Foot Controller

Control 2 Owner’s Manual

Selecting Banks
The Control 2 assigns groups of presets (called banks) to the numbered
footswitches. Each bank is a group of 5 presets (5 Patch Mode) or 10 presets
(10 Patch Mode) depending on the foot controller mode selected by the GSP.
Hence, there are 20 banks in 5 Patch Mode and 10 banks is 10 Patch Mode.
To select a new bank and a new preset, follow these steps:
Press either the Bank Down or Bank Up footswitch. The name of
the newly cued bank appears in the Display and the available preset
footswitches flash (1-5 in 5 Patch Mode and 1-10 in 10 Patch Mode).
Bank Down & Bank Up
To make the bank shown in the Display active you must load a new
preset by pressing one of the flashing preset footswitches. If no
footswitch is pressed within 5 seconds, the Control 2 will abort the
bank change and return to the preset prior to the bank footswitch being
pressed.
Banks are also changed when selecting presets using the Edit/Select knob
on the GSP. For example, if any of presets 1-5 are selected on the GSP in 5
Patch Mode, the bank titled Presets 1-5 will be the active bank on the
Control 2 and numbered Footswitches 1-5 would select presets 1-5. If preset
6 is then selected using the Edit/Select knob on the GSP, Presets 6-10
will now become the active bank and numbered Footswitches 1-5 would then
select presets 6-10.
Note that banks titled Presets 96-99 (5 Patch Mode) and Presets
91-99 (10 Patch Mode) contain only 4 and 9 presets respectively. When one
of these banks is selected, Footswitch 5 (5 patch mode) and the CONTROL
Footswitch (10 patch mode) have no function.
1.
2.
Using the Control 2 Remote Foot Controller
Control 2 Owner’s Manual

Selecting Presets
To select a preset in 5 Patch or 10 Patch Mode, follow these steps:
Press one of the footswitches numbered 1-5 (footswitches numbered 1-
10 in 10 Patch Mode). The associated footswitch LED will light and the
preset name and number will appear in the Display.
To select another preset, press another of the footswitches numbered
1-5 (footswitches numbered 1-10 in 10 Patch Mode). The previous
footswitch LED will turn off and the newly pressed footswitch’s LED will
now light.
In 5 Patch Mode, as different presets are selected, different effect footswitch
LEDs (Footswitches 6-10) will turn on and off based on the status of these
effects in the active preset.
Bypassing Presets
To bypass an active preset, press the active preset footswitch. The Display
will read BYPASS when the preset is bypassed and the preset footswitch you
bypassed from will remain lit (in 5 Patch Mode, the effects footswitches that
were on before bypassing will also remain lit). To return to the same preset
from bypass, press the lit preset footswitch again and the last preset loaded
will become active again.
You can also change to another preset from bypass by pressing any non-lit
preset footswitch. In 5 Patch Mode, you can also turn any of the effects
(DISTORTION, CHORUS/FX, DELAY, REVERB) on or off when exiting bypass
by pressing one of these footswitches instead of a preset footswitch. This
will load the last active preset and turn the respective effect on or off as it is
loaded.
NOTE: Bypassing presets with the footswitches is not available if the Bounce
Back feature is enabled. Refer to the Bounce Back section on page 8 for
more information about the Bounce Back feature.
Turning Effects On or Off
In 5 Patch Mode, Footswitches 6-9 are programmed to turn on or off the
following effects in the active preset:
Footswitch 6 controls the Distortion on/off.
Footswitch 7 controls the Chorus/FX on/off.
Footswitch 8 controls the Delay on/off.
Footswitch 9 controls the Reverb on/off.
Footswitch 10 can also be programmed to turn on and off effects as
well. See page 11 for more information about assigning effect on/off and
parameters to the CONTROL footswitch).
1.
2.

Control 2 Owner’s Manual
Using the Control 2 Remote Foot Controller

When you load a preset, some effects may already be on.Those effects will
have a lit LED next to their footswitch(es).
To turn effects on or off using Footswitches 6-10, follow these steps:
Make sure the Control 2 is in 5 Patch Mode (see page 5 for instructions
on how to switch modes).
Press one of the footswitches numbered 6-10.The footswitch’s LED
turns on to indicate the effect is active, or turns off to indicate the effect
is bypassed.
Bounce Back
Bounce Back allows switching between two presets using a single footswitch
in both 5 Patch and 10 Patch modes.
To enable the Bounce Back feature, follow these steps:
From the preset screen, press the Edit/Select knob once to enter the
menu navigation system.
Turn the Edit/Select knob until the Foot Controller menu is selected
and press the knob again.
In the Foot Controller menu, select Bounce Back and press the Edit/
Select knob to turn this feature on or off.
Press the Back button to save this setting.
Bounce Back only works within each active bank of presets, meaning you
cannot select preset 1 in the Presets 1-5 bank, change banks, select
preset 51 in the Presets 51-55 bank and then bounce back to preset 1.
NOTE: When Bounce Back is enabled, bypassing presets from the Control 2
is no longer available.
To use the Bounce Back feature, follow these steps:
Select a preset using an available preset footswitch (for our example,
we’ll use Footswitch 1 – Preset 1).
Select another preset (for our example, Footswitch 4 – Preset 4).
Press Footswitch 4 again. Preset 1 is loaded.
Subsequent presses of numbered Footswitch 4 will alternately load
Preset 4 and Preset 1. Pressing any other preset footswitch will abandon
the bounce back between these two presets.
1.
2.
1.
2.
3.
4.
1.
2.
3.
4.
Control 2 Owner’s Manual
Using the Control 2 Remote Foot Controller

Volume Update
Volume Update lets you maintain relative volume levels between presets
when using the Control 2’s expression pedal as a volume controller. Using
this feature requires that presets have the Control 2’s built-in expression
pedal, an external expression pedal connected to the GSP or Control 2, or a
MIDI expression pedal linked to the Volume Pre or Volume Post parameters
in the GSP’s presets. With Volume Update set to ON, the pedal’s position is
maintained after changing presets thus keeping the relative volume the same
even when the volume is backed off. When Volume Update is set to OFF,
presets are set to the volume level stored with the preset when they are
selected.
To enable or disable the Volume Update option, follow these steps:
From the preset screen, press the Edit/Select knob once to enter the
menu navigation system.
Turn the Edit/Select knob until the Foot Controller menu is highlighted
and press the knob again.
In the Foot Controller menu, highlight Volume Update and press the
Edit/Select knob to turn this option on or off.The default setting is on.
Press the Back button to save this setting.
MIDI CC Send
In addition to controlling GSP processor parameters, you can configure the
Control 2’s Expression Pedal and the CONTROL Footswitch to send MIDI
CC (continuous controller) messages on the GSP’s MIDI channel to MIDI
devices connected to your GSP’s MIDI Thru port. The Expression Pedal can
act as a continuous control device, and the CONTROL Footswitch can act as
a parameter toggle switch.
To enable the MIDI CC send options for the Control 2 Expression Pedal and
the CONTROL Footswitch, follow these steps:
From the preset screen, press the Edit/Select knob once to enter the
menu navigation system.
Turn the Edit/Select knob until the Foot Controller menu is highlighted
and press the knob again.
In the Foot Controller menu, highlight MIDI CC Send and press the
Edit/Select knob.The MIDI CC Send menu appears.
To enable CC send and assign a MIDI CC that the Control 2’s
Expression Pedal will transmit, highlight FC PDL and press the Edit/
Select knob.
Turn the Edit/Select knob to select the desired MIDI CC and press the
1.
2.
3.
4.
1.
2.
3.
4.
5.

Control 2 Owner’s Manual
Using the Control 2 Remote Foot Controller

knob to select it.
To enable CC send and assign a MIDI CC that the CONTROL
Footswitch will transmit, highlight FC FSW and press the Edit/Select
knob.
Turn the Edit/Select knob to select a MIDI CC and press the knob to
select it.
Expression Pedal Calibration
In order to smoothly control parameters using the Control 2’s expression
pedal, the pedal needs to be calibrated the first time it is connected to the
GSP. This is done using the FC Pedal Calibrate menu in the GSP.
To calibrate the Control 2’s Expression Pedal, follow these steps:
From the preset screen, press the Edit/Select knob once to enter the
menu navigation system.
Turn the Edit/Select knob until the Foot Controller menu is highlighted
and press the knob again.
In the Foot Controller menu, highlight Pedal Calibrate and press the
Edit/Select knob to start the calibration procedure.
Once started, the Control 2’s Display will show TOE DOWN. Rock the
expression pedal full forward and press the flashing TUNER footswitch.
Calibration is now complete.
NOTE: You need to rock the Expression Pedal all the way forward and
all the way back each time you power up the Control 2 to re-establish
its Min and Max positions.
6.
7.
1.
2.
3.
4.
0 Control 2 Owner’s Manual
Using the Control 2 Remote Foot Controller

Tuner
The Control 2 provides access to the host GSP’s tuner and provides tuner
feedback via the Control 2’s Display.
To tune your guitar, follow these steps:
Press the TUNER footswitch. The Control 2’s Display will briefly show
TUNER and the TUNER footswitch LED will now be lit. The guitar
signal is normally muted when the tuner is accessed. You can rock the
Expression Pedal forward to hear the note while it is being tuned.
Begin playing a note on the guitar. The leftmost characters of the Display
will show the note being played. The rest of the Display will show
arrows indicating the relative tuning. An arrow pointing to the left ( )
indicates the note is sharp and should be tuned down. An arrow pointing
to the right ( ) indicates the note is flat and should be tuned up.When
your note is in tune, is displayed.
Press any footswitch (or the Back button or the Edit/Select knob on
the GSP) to return to the preset.
Assigning Parameters to the CONTROL
Footswitch (#10)
You can set up the CONTROL footswitch to control a parameter of your
choice, including each effect’s On/Off parameter.To assign a parameter to the
CONTROL footswitch, follow these steps:
From the Preset screen on the GSP, press the Edit/Select knob twice.
Turn the Edit/Select knob to highlight Expression Links and press the
Edit/Select knob.The Edit Expression Links menu appears.
Scroll down and highlight an expression link that is not in use (NO CTRL
NO LINK). Press the Edit/Select knob to select the expression link.
The Linking menu appears.
Make sure Assign Controller is highlighted and press the Edit/Select
knob.
1.
2.
3.
1.
2.
3.
4.

Control 2 Owner’s Manual
Using the Control 2 Remote Foot Controller

Turn the Edit/Select knob until <FC FSW> appears.
Press the Edit/Select knob.The Linking menu appears.
Scroll down and highlight LINKED TO NO LINK. Press the Edit/Select
knob.
Turn the Edit/Select knob to select a parameter to assign to the
CONTROL footswitch and press the Edit/Select knob.
Pressing the CONTROL footswitch now toggles between the selected
parameter’s Min and Max values.The Min and Max values are automatically
updated with the selected parameter’s defaults.You can also edit the Min and
Max values to customize the parameter range for your needs using the Edit/
Select knob.
Changes must be stored using the GSP’s Store procedure. Consult your GSP
documentation for more information about storing changes to presets.
Assigning Parameters to the Expression Pedals
The Control 2 features two expression pedal controller options: the built-
in Expression Pedal and an optional expression controller which can be
connected to the rear panel of the Control 2. Assigning parameters to either
expression controller involves the same process.To assign a parameter to
either expression pedal controller, follow these steps:
From the Preset screen on the GSP, press the Edit/Select knob twice.
Turn the Edit/Select knob to highlight Expression Links and press the
Edit/Select knob.The Edit Expression Links menu appears.
Scroll down and highlight an expression link that is not in use (NO CTRL
NO LINK). Press the Edit/Select knob to select the expression link.
The Linking menu appears.
Make sure Assign Controller is highlighted and press the Edit/Select
knob.
To assign a parameter to be controlled by the Control 2’s built-in
Expression Pedal, turn the Edit/Select knob until <FC PDL1> appears.
To assign a parameter to be controlled by the Control 2’s optional rear
panel expression pedal, turn the Edit/Select knob until <FC PDL2>
appears.
Press the Edit/Select knob.The Linking menu appears.
Scroll down and highlight LINKED TO NO LINK. Press the Edit/Select
knob.
Turn the Edit/Select knob to select a parameter to assign to the
Expression Pedal and press the Edit/Select knob.
5.
6.
7.
8.
1.
2.
3.
4.
5.
6.
7.
8.
9.
2 Control 2 Owner’s Manual
Using the Control 2 Remote Foot Controller

The Min and Max values are automatically updated with the selected
parameter’s defaults.You can also edit the Min and Max values to customize
the parameter range for your needs using the Edit/Select knob.
Changes must be stored using the GSP’s Store procedure. Consult your GSP
documentation for more information about storing changes to presets.

Control 2 Owner’s Manual
Using the Control 2 Remote Foot Controller

DigiTech®
0 South Sandy Parkway
Sandy, Utah 00
PH (0) -00
FAX (0) -00
http://www.digitech.com
Printed 2/200
Control 2 Remote Foot Controller Owner’s Manual
-02-A
© 2007 Harman International Industries, Incorporated. All Rights Reserved.