digi-tech VOCALIST LIVE 2 User manual

Vocal Harmony and
Effects Processor
Owner’s
Manual

WARNING FOR YOUR PROTECTION
PLEASE READ THE FOLLOWING:
KEEP THESE INSTRUCTIONS
HEED ALL WARNINGS
FOLLOW ALL INSTRUCTIONS
THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING LIQUID
AND NO OBJECT FILLED WITH LIQUID, SUCH AS VASES, SHALL BE PLACED
ON THE APPARATUS.
CLEAN ONLY WITH A DRY CLOTH.
DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE
WITH THE MANUFACTURER’S INSTRUCTIONS.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT
REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT
PRODUCE HEAT.
ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.
UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR
LONG PERIODS OF TIME.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or
third prong are provided for your safety. If the provided plug does not fit
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Use only with the cart stand, tripod bracket, or table specified by the manu-
facture, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
Refer all servicing to to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
POWER ON/OFF SWITCH: The Power switch used in this piece of equipment
DOES NOT break the connection from the mains.
MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount
or installation where plug is not accessible, an all-pole mains switch with a
contact separation of at least 3 mm in each pole shall be incorporated into
the electrical installation of the rack or building.

DECLARATION OF CONFORMITY
Manufacturer’s Name: DigiTech®
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, U.S.A.
declares that the product:
Product name: Vocalist®Live 2
Product option: all (requires Class II power adapter that conforms
to the requirements of EN60065, EN60742, or
equivalent.)
conforms to the following Product Specifications:
Safety EN 60065
EMC EN 55103-1
EN 55103-2
Supplementary Information:
The product herewith complies with the requirements of the Low
Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC as
amended by Directive 93/68/EEC.
Vice-President of Engineering - MI
8760 S. Sandy Parkway
Sandy, Utah 84070, U.S.A.
Date: February 1, 2007
European
Contact: Your local DigiTech Sales and Service Office or
Harman Music Group
8760 South Sandy Parkway
Sandy, Utah, 84070 U.S.A.
Ph: [phone]
Fax: [phone]
Warning
For your protection, please read the following:
Important Safety Instructions
Read these instructions.
Keep these instructions.
Heed all warnings.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in ac-
cordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
No user serviceable parts inside. Refer all servicing
to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the ap-
paratus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been
dropped.
WARNING:To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or
moisture.
Refer to labels on the unit, including bottom cover, or
other markings and pertinent information.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.

Warranty
We at DigiTech®are very proud of our products and back up each one we sell with the following warranty:
1. The warranty registration card must be mailed within ten days after purchase date to validate this
warranty.
2. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and
workmanship under normal use and service.
3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show
evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION,
where all parts and labor will be covered up to a period of one year.A Return Authorization number may
be obtained from DigiTech by telephone.The company shall not be liable for any consequential damage as a
result of the product’s use in any circuit or assembly.
4. Proof-of-purchase is considered to be the burden of the consumer.
5. DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this
product without incurring any obligation to install the same on products previously manufactured.
6. The consumer forfeits the benefits of this warranty if the product’s main assembly is opened and tampered
with by anyone other than a certified DigiTech technician or, if the product is used with AC voltages outside
of the range suggested by the manufacturer.
7. The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor
authorizes any person to assume any obligation or liability in connection with the sale of this product. In no
event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the
performance of this warranty due to causes beyond their control.
NOTE:The information contained in this manual is subject to change at any time without notification. Some
information contained in this manual may also be inaccurate due to undocumented changes in the product or
operating system since this version of the manual was completed.The information contained in this version of
the owner’s manual supersedes all previous versions.

Table of Contents
Introduction ........................................................................................................... 1
The Vocalist®Live 2 Features .....................................................................1
About musIQTM Technology........................................................................1
Included Items........................................................................................................ 2
A Guided Tour of the VocalistTM Live 2.............................................................3
Overview ........................................................................................................3
Quick Start..................................................................................................... 3
Front Panel .....................................................................................................4
Indicator LEDs (Guitar Signal, Phantom Power,Vocal Signal)......5
Guitar Tuner LEDs................................................................................5
Knobs ......................................................................................................5
Select Buttons....................................................................................... 6
Rear Panel....................................................................................................... 7
Phantom Power .................................................................................... 7
Guitar Ground Lift...............................................................................7
Guitar In.................................................................................................7
Guitar Thru............................................................................................ 8
Mic/Line Input Level............................................................................. 8
Mic In ...................................................................................................... 8
Line In ..................................................................................................... 8
Line Out L/R..........................................................................................8
Mono Out ............................................................................................. 8
Power Input...........................................................................................8

Getting Started...................................................................................................... 9
Connect the Microphone, Guitar, and P.A. or Mixer.............................9
Set the Vocalist®Live 2 Controls............................................................... 10
Set up the Mixer for Stereo Operation
(If Using Two Channels of a Mixer)........................................................... 11
Common Setups....................................................................................................12
Guitar and Microphone In/Guitar Amp and P.A. Out (Mono) ............ 12
Guitar and Microphone In/P.A. Out (Mono or Stereo)........................13
Guitar and Microphone In/P.A. and Powered Monitor Out................ 14
Guitar and Mixer or Preamp in/P.A. Out.................................................15
The Vocalist Live 2 Controls...............................................................................16
Harmony Mix Knob .....................................................................................16
Harmony Select Buttons .............................................................................16
Compressor Knob........................................................................................17
Enhance Knob and Buttons ........................................................................ 17
Reverb Knob and Buttons ..........................................................................18
Effects Footswitch.........................................................................................18
Harmony Footswitch ................................................................................... 19
Guitar Tuner...................................................................................................19
Some Usage Notes.......................................................................................20
Setting Levels on the Vocalist Live 2 .................................................................21
Troubleshooting.....................................................................................................22
Specifications.......................................................................................................... 24

1
Introduction
Congratulations on your purchase of the Vocalist™ Live 2. TheVocalist Live 2 is the world’s first
processor that automatically generates live multi-part vocal harmony by analyzing guitar chord
progressions. Armed with patent pending musIQ™ Harmony Technology (which includes both
musIQ note detection and musIQ harmony generation), the VL-2 gives you accurate vocal harmo-
nies even with complicated songs because only Vocalist Live tracks guitar chords, along with your
voice.
The Vocalist®Live 2 Features
musIQ harmony technology.
One or two voices of automatic harmony with selectable voicings (Unison 1, Unison 2, High,
Higher, Low, Lower), generated based on incoming music from your guitar.
Selection of lead voice effects (Reverb, Compressor, and Enhance effects).
Built-in guitar tuner.
Built-in microphone preamp.
Next-generation vocal pitch detection, pitch shifting, and humanization processing.
+48V phantom power.
24-bit/44.1kHz audio quality.
About musIQTM Technology
musIQ is a revolutionary technology that eliminates the need to enter key and scale informa-
tion into the product as it listens to the notes/chords played on a guitar and makes sure that the
harmony voices fit with the music. Real-time processing discerns the individual notes and key
signatures that are played to automatically generate appropriate vocal harmonies that comple-
ment the lead vocal. With musIQ, you can focus on your live singing and playing performance, and
discard song programming once and for all.
•
•
•
•
•
•
•
•

2
Included Items
Before you get started, please make sure that the following items have been included:
The Vocalist®Live 2
PS0913B Power Supply
This owner’s manual
Warranty Card
The utmost care was taken while yourVocalist Live 2 was being manufactured. Everything should
be included and in perfect working order. If anything is missing, contact the factory at once. Please
help us become acquainted with you and your needs by completing your warranty card or regis-
tering online at www.digitech.com. It is your safeguard should a problem arise with your Vocalist
Live 2.
Important safety tip: Always turn on amplifiers AFTER all other connections are made to the
Vocalist Live 2 and AFTER the Vocalist Live 2 is powered up.
•
•
•
•

3
A Guided Tour of the Vocalist®Live 2
Overview
The Vocalist®Live 2 is a revolutionary voice processor that creates musically correct harmonies
for your singing voice that automatically change to fit with the current guitar chord and key of the
music you have been playing.
Quick Start
It’s a good idea to read this brief manual completely, but if you want to start using the Vocalist Live
2 right away, go to the Getting Started section on page 9.
For more information on what the knobs and buttons do, refer to The Vocalist Live 2 Controls
section on page 16.
To find out about using the tuner, see the Guitar Tuner section on page 19.
To locate and identify the various controls, inputs, and outputs, see the Front Panel and Rear Panel
sections on pages 4 and 7.

4
Front Panel
1
2
3
4
5
6

5
Indicator LEDs (Guitar Signal, Phantom Power,Vocal Signal)
The indicator LEDs show the status of Phantom power (off or on) and the incoming signal
levels for the guitar and microphone.The Guitar Signal and Vocal Signal LEDs light
green when a signal is present, amber when the incoming signal is approaching clip (over-
load), and red when the incoming signal clips. For more information, see Setting Levels on
the Vocalist®Live 2 on page 21.
Guitar Tuner LEDs
When the guitar tuner is active, the letter and # LEDs indicate what note is being played.
If the # LED lights up in addition to a letter LED, that means the note is a sharp note (like
A#).The bar of eleven LEDs shows whether the note being played is slightly sharp (right of
triangle), slightly flat (left of triangle), or in tune (directly below triangle).
Knobs
Compressor
Adding the right amount of compression smooths out incoming vocal dynamics and creates
a more even vocal performance.Turn this knob clockwise to increase compression, or coun-
ter-clockwise to decrease compression. See page 17 for more information about compres-
sion.
Reverb
Sets the amount of reverb that is applied to the incoming microphone signal.Turn this knob
clockwise to increase reverb, or counter-clockwise to decrease reverb. Select the type of
reverb with the Reverb buttons, described on page 18.
Enhance
Enhance effects apply equalization and “sweetening” effects to the lead microphone signal
that improve intelligibility and presence.Turn this knob clockwise to increase Enhance effects,
or counter-clockwise to decrease Enhance effects. Select the type of Enhance effect with the
Enhance buttons, described on page 17.
1.
2.
3.

6
Harmony Mix
Adjusts the level of the harmony vocals relative to the incoming lead vocal (your voice).Turn
this knob clockwise to increase harmony levels and decrease the lead vocal, or counter-
clockwise to decrease harmony levels and increase the lead vocal.
Select Buttons
These enable and disable reverbs, effects, and harmonies. See the following pages for more
information:
Reverb - Page 18.
Enhance - Page 17.
Harmony - Page 16.
Harmony Footswitch
Press this footswitch to enable or disable the vocal harmonies.
Effects/Tuner Footswitch
Press this footswitch to enable or disable any selected effects (reverb, compressor, etc.). Press
and hold this footswitch to enable the guitar tuner. Press the Effects/Tuner Footswith again to
disable the guitar tuner. See page 19 for more information about the guitar tuner.
NOTE: It is important that your guitar is properly tuned in order to get the best
sounding harmonies.Alternate tunings such as DADGAD are fine, as long as the
tuning system used specifies a frequency of 440 Hz for A (A440), and it is based
on the chromatic scale (12 notes per octave). Micro-tonal scales are not sup-
ported.
4.
5.
6.

7
Rear Panel
Phantom Power
Enables 48 volt phantom power on the XLR mic input.
Note: Phantom power is normally only needed with condenser microphones and should
never be used with ribbon microphones.To avoid damaging the microphone, please consult
your microphone documentation to ensure phantom power is applied only when appropriate.
Guitar Ground Lift
Eliminates most “hum” problems. If you hear a humming sound or buzz coming from your
amp or P.A., try pressing this button.
Guitar In
Connect a guitar directly to this high-impedance input. Note that there is no loss of quality
between the Guitar in and Guitar Thru jacks.
1.
2.
3.
Guitar In
Phantom Power
L R
Guitar Thru
Mono Out
Line Out
Line In
Mic In
Mic/Line
Input Level
Guitar
Ground Lift
OFF ON musIQ is a trademark
of 3dB Research
9VAC
1.3A
1
56 7 8 9 10
2 3 4

8
Guitar Thru
Connect a guitar amplifier or powered speaker directly to this output.
Mic/Line Input Level
This knob adjusts the gain of the Mic and Line inputs.Turn clockwise to increase gain, or
counter-clockwise to decrease gain. If the Vocal Signal LED is turning red while you sing,
you need to decrease the Mic gain.
Mic In
Connect a dynamic or condenser microphone to this XLR input.This input is the lead voice
for the Vocalist®Live 2.
Line In
Connect a line input source (mixer, mic preamp, etc.) to this input. When connected to a
source, this input is the lead voice for the Vocalist Live 2, and disables the Mic In XLR input.
Line Out L/R
Connect these balanced/unbalanced outputs to a mixer, powered speakers or P.A. system
if a stereo mix is desired. Only vocal, harmonies, and vocal effects are heard from the Line
Outputs. Harmonies sent through these outputs are panned slightly to the left (Line Out
L) and right (Line Out R).
Mono Out
Connect this XLR balanced output to a powered speaker or mixer if a mono mix is desired.
Only vocal, harmonies, and vocal effects are heard from this output.
Power Input
Connect only the DigiTech®PS0913B power supply to this jack.
4.
5.
6.
7.
8.
9.
10.

9
Getting Started
Before connecting the Vocalist®Live 2, make sure that the power to your amplifier is off and that
the Vocalist Live 2 is plugged into the wall and powered on.There is no power switch on the Vocal-
ist Live 2.To turn the Vocalist Live 2 on or off, connect or disconnect the included PS0913B power
supply from the Power Input jack.
Connect the Microphone, Guitar, and P.A. or Mixer
Plug a microphone into the Vocalist Live 2 Mic In jack.
If you need phantom power, press the Phantom Power switch on theVocalist Live 2 back
panel.The Phantom Power LED will illuminate.
Note: Phantom power is normally only needed with condenser microphones, and should
never be used with ribbon microphones.To avoid damaging the microphone, please consult
your microphone documentation to ensure phantom power is applied only when appropriate.
Plug your guitar into the Vocalist Live 2 Guitar In jack.
Make sure your guitar amplifier is turned off and the volume level is turned all the way down.
Connect the Vocalist Live 2 Guitar Thru to your amplifier’s input or the P.A. system.
Make sure your P.A. or mixer is turned off and the volume levels are turned all the way down.
Plug the Vocalist Live 2 Left and Right Line Outputs into your P.A. system or mixer. Or, if
you are only using a single channel or mono amplification system, plug only the Vocalist Live 2
Mono output into the P.A. system or mixer.
1.
2.
3.
4.
5.
6.
7.

10
Set the Vocalist®Live 2 Controls
Turn the Compressor, Reverb, and Enhance knobs all the way down (counter-clockwise).
Turn the Harmony Mix knob to the 11 o’clock position.
Power up theVocalist®Live 2 by connecting the PS0913B power supply.
Press the High button so that it is lit.
Press the HARMONY FOOTSWITCH so that the HARMONY LED just above it is lit.
Adjust Levels and Tune Your Guitar
Observe the Guitar Signal LED while playing your guitar. Adjust the output level of your
guitar until the Guitar Signal LED lights green or amber most of the time. (For more infor-
mation about setting levels, see page 21.)
Perform the obligatory “Check 1-2” or sing into the mic while gradually turning up theVocal-
ist Live 2 Mic/Line Input Level knob until the Vocal Signal LED lights amber most of the
time. (For more information about setting levels, see page 21.)
Press and hold the EFFECTS FOOTSWITCH until the TUNING LEDs light up. Tune
each string until the center (green LED below the triangle) LED illuminates for each string,
indicating it’s in tune.
NOTE: It is important that your guitar is properly tuned in order to get the best
sounding harmonies. Alternate tunings such as DADGAD are fine, as long as the
tuning system used specifies a frequency of 440 Hz for A (A440), and it is based
on the chromatic scale (12 notes per octave). Micro-tonal scales are not sup-
ported.
1.
2.
3.
4.
5.
1.
2.
3.

11
Turn on your amplifier and gradually turn it up until you reach a comfortable listening level.
Turn on your P.A. system and gradually turn it up until you reach a comfortable listening level.
While playing a chord on your guitar, sing a note.You should hear your guitar and your voice,
plus a harmony voice. If not, repeat the steps above or consult the Troubleshooting section on
page 22.
Set up the Mixer for Stereo Operation (If Using Two Channels of a Mixer)
Turn the Vocalist®Live 2 Mic/Line Input Level knob completely counter-clockwise.
Set the mixer channels’ faders to 0dB.
Set the mixer’s master fader to its minimum position (no output signal).
Set the pan controls on the selected mixer channels hard left and hard right.
While singing, gradually turn up the Vocalist Live 2’s Mic/Line Input Level knob until the
Vocal Signal LED lights amber most of the time, and red during the loudest parts only. (For
more information about setting levels, see page 21.)
Gradually bring the mixer’s master fader up until you reach your desired level.
4.
5.
6.
1.
2.
3.
4.
5.
6.

12
Common Setups
There are several ways to set up the VocalistTM Live 2. Some useful setups are shown here.
Guitar and Microphone In/Guitar Amp and P.A. Out (Mono)
Guitar In
Phantom Power
L R
Guitar Thru
Mono Out
Line Out
Line In
Mic In
Mic/Line
Input Level
Guitar
Ground Lift
OFF ON musIQ is a trademark
of 3dB Research
9VAC
1.3A
Guitar amp
Mixer/
P.A. system
Pan
Mute
-10
0
+5
+10
-20
-30
-
-5
L / R
Mute
L / R
Mute
L / R
Mute
L / R
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5
1 2 3 4
-10
0
+5
+10
-20
-30
-
-5
-10
0
+5
+10
-20
-30
-
-5
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
5
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
6
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
-10
0
+5
+10
-20
-30
-
-5
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Mute
L / R
-10
0
+5
+10
-20
-30
-
-5

13
Guitar and Microphone In/P.A. Out (Mono or Stereo)
Guitar In
Phantom Power
L R
Guitar Thru
Mono Out
Line Out
Line In
Mic In
Mic/Line
Input Level
Guitar
Ground Lift
OFF ON musIQ is a trademark
of 3dB Research
9VAC
1.3A
Mixer/
P.A. system
Pan
Mute
-10
0
+5
+10
-20
-30
-
-5
L / R
Mute
L / R
Mute
L / R
Mute
L / R
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5
1 2 3 4
-10
0
+5
+10
-20
-30
-
-5
-10
0
+5
+10
-20
-30
-
-5
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
5
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
6
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
-10
0
+5
+10
-20
-30
-
-5
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Mute
L / R
-10
0
+5
+10
-20
-30
-
-5
Stereo
Mono
or

14
Guitar and Microphone In/P.A. and Powered Monitor Out
Guitar In
Phantom Power
L R
Guitar Thru
Mono Out
Line Out
Line In
Mic In
Mic/Line
Input Level
Guitar
Ground Lift
OFF ON musIQ is a trademark
of 3dB Research
9VAC
1.3A
Mixer/
P.A. system
Pan
Mute
-10
0
+5
+10
-20
-30
-
-5
L / R
Mute
L / R
Mute
L / R
Mute
L / R
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5 Pan
-5
-4
-3
-2
-1 0+1
+2
+3
+4
+5
1 2 3 4
-10
0
+5
+10
-20
-30
-
-5
-10
0
+5
+10
-20
-30
-
-5
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
5
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
6
-10
0
+5
+10
-20
-30
-
-5
Mute
L / R
-10
0
+5
+10
-20
-30
-
-5
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Aux 1
0
2
4 6
8
10
Aux 2
0
2
4 6
8
10
Mute
L / R
-10
0
+5
+10
-20
-30
-
-5
Powered monitor