Digimerge DGR204 Instruction Manual

1
Four Channel Networkable
Digital Video Recorder
Model: DGR204
Installation / User Manual
Digimerge Technologies Inc.

2
All the following safety and operated instructions which will prevent harm or damage to the operator
and other persons should be read before the unit is operated.
SAFETY PRECAUTIONS
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
Do not block ventilation openings.
Do not place anything on top of the unit that might spill or fall into it.
Do not attempt to service this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Please refer all servicing to qualified service personnel.
Do not use liquid cleaners or aerosols for cleaning.
This installation should be by a qualified service person and should conform to all local codes.
To prevent fire or electric shock, do not overload wall outlets or extension cord.
This unit must be grounded to reduce the risk of electric shock hazard.
CAUTION
Danger of explosion if the Lithium battery (RTC Battery) is incorrectly replaced.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions.
Risk of explosion if replaced by an incorrect type. Dispose of used batteries according to the
instructions.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his/her own expense.

3
Table Of Contents
1. PRODUCT FEATURES .................................................................................................... 5
1.1 Product Introduction ..................................................................................................................5
1.2 Product Features........................................................................................................................5
2. DESCRIPTION OF THE FRONT/REAR VIEW ................................................................ 6
2.1 Front View ..................................................................................................................................6
2.2 Rear View ...................................................................................................................................9
2.3 ALARM In/Out .........................................................................................................................10
3. INSTALLATION .............................................................................................................. 11
3.1 Basic Connection ..................................................................................................................... 11
3.2 Hard-Disk Drive Installation ...................................................................................................12
3.3 System Information and channel selection...............................................................................13
3.4 Updating System Software .......................................................................................................15
4. BASIC OPERATIONS .................................................................................................... 16
4.1 Configuring Recording Settings ...............................................................................................16
4.2 Recording Operations ..............................................................................................................18
4.3 Playback Operations................................................................................................................23
4.4 Search Operations....................................................................................................................24
4.5 Backup Operations...................................................................................................................28
4.6 Key Lock Operation .................................................................................................................31
5. MENU SETUP ................................................................................................................ 32
5.1 REC SETTING .........................................................................................................................33
5.2 ALARM SETTING ....................................................................................................................34
5.3 TIMER/ SEQ/ TITLE................................................................................................................37
5.4 COMMUNICATION ................................................................................................................39
5.5 DISK SETTING........................................................................................................................42
5.6 SYSTEM ...................................................................................................................................43
6. RS-232 & RS-485 PROTOCOL ..................................................................................... 46
6.1 Setup.........................................................................................................................................46

4
6.2 Communication Protocol .........................................................................................................46
7. IDE HARD DISK INSTALLATION.................................................................................. 49
7.1 Mobile Rack HDD Installation ................................................................................................49
8. SYSTEM DEFAULT........................................................................................................ 52
9. O.S.D. MESSAGE .......................................................................................................... 54
10. NETWORK VIEWER AND IMAGE VIEWER ............................................................... 55
10.1 The Network Viewer ...............................................................................................................55
10.2 The Image Viewer...................................................................................................................64
11. INDEX TABLE .............................................................................................................. 65
12. NETWORK CONFIGURATION .................................................................................... 66
12.1 Cable Connections .................................................................................................................66
12.2 Configure Your DVR Network Settings ..................................................................................67
12.3 TCP/IP Communication Software..........................................................................................69
12.4 TCP/IP installation ................................................................................................................71
12.5 TCP/IP Configuration setting ................................................................................................71
12.6 Connection Testing.................................................................................................................72
13. SPECIFICATIONS ........................................................................................................ 74
APPENDIX 1. –SCANIP ................................................................................................................75
15. LIMITED WARRANTY.................................................................................................. 78

5
1. PRODUCT FEATURES
1.1 Product Introduction
The DGR204 four channel Digital Video Recorder (DVR) provides high quality storage of up to four
video sources. Equipped with a range of comprehensive features, such as video motion detection,
pre-alarm recording, thumbnail search, jog/shuttle function, hard drive expansion, and TCP/IP
connectivity, this DVR will make your applications far more flexible and effective than ever before.
1.2 Product Features
＊ Dual Hard Drive Support. (One Internal, One Hot-Swappable)
＊ Pre-alarm image recording.
＊ Time-lapse and real-time recording.
＊ Refresh rate up to 60 IPS.
＊ Image quality selectable at 4 different levels for recording.
＊ Event/Timer/Alarm recording mode.
＊ Quick search by time, alarm, event, and recording list.
＊ Fast and slow playback of recorded video at various speeds.
＊ Single-picture playback.
＊ On-screen setup menu, title and system timer.
＊ Password protection.
＊ Disk-full warning and operation status LEDs.
＊ RS-232, RS-485 communication port.
＊ Remote control via RS-232, RS-485 and Ethernet ports
＊ Power interruption recovery.
＊ Operation-status record log.
＊ Distributing live and recorded images through TCP/IP network environment.
＊ Audio recording capability
＊ Built-in SD (Secure Digital) memory card slot for image retrieval.
＊ Support DHCP protocol.

6
2. DESCRIPTION OF THE FRONT/REAR VIEW
2.1 Front View
A-rec T-recDISK
1 223 24
Power
7
Search
10
Seq.
/Save
16
Setup
9 11 1413 12
Enter
15
Display
8
18
20
19
21
17
Play
4
Pause
3
Stop
5
SD Card
Rec
6
22
ZOOM
Hard-disk drive compartment.
This compartment houses the removable (hot-swappable) hard disk drive.
NOTE: The compartment must be locked before the hard drive can be used.
Hard disk compartment lock:
The key lock secures a hard disk in place. Unlock the compartment before you remove the hard
disk cartridge from the unit.
PAUSE button:
Press the PAUSE button to pause the video during playback. Pressing the PAUSE button while in
the PAUSE MODE will advance the video by one frame.
The green “PAUSE” LED will be illuminated.
PLAY button:
Press the PLAY button to play recorded video from the hard disk.
The green LED under the “PLAY” button will be illuminated
STOP button:
Press the STOP button to stop the playing of video during playback, or stop recording during a
manual record.
The green LED under the “STOP” button will be illuminated
REC button:
Press the REC button to start manually recording video onto the hard disk while viewing live
video display mode.
The red LED under the REC button will be illuminated.
POWER button:
Press and hold POWER button for 3 seconds to turn on the unit, press (and hold again) to turn

7
the unit off.
DISPLAY button:
Press to show the system operation status on the screen. (See Section 3.3 for Display indications)
Setup button:
Press this to enter the setup menu. Press again to exit the setup mode.
Search button:
Press the SEARCH to enter the search mode to access recorded video.
Left / Right (CH1 / CH2 ) buttons:
In setup menu/ search mode, use these buttons scroll Left/Right to select desired items in the
menu setup mode.
For Key Lock operation, press these two buttons simultaneously once; to disable Key Lock,
press these two buttons simultaneously again.
In live mode, use these buttons to select channel 1 or 2 for display.
In play mode, use these buttons to select a channel 1 or 2 as well as zoom in on the desired
channel.
Up / Down ( CH3 / CH4 )buttons:
In setup menu/ search mode, use these buttons to scroll Up/Down to select the desired items
options for programming.
In live mode, use these buttons to select channel 3 or 4 for display.
In play mode, use these buttons to select a channel 3 or 4 as well as zoom in on the desired
channel.
Enter / (Quad) Button:
Press the ENTER button to select or enter an item while in the setup menu.
When changing a value within the setup menu, press the ENTER to save the change.
This button also switches to the 4 camera view during live or playback viewing.
Seq./Save button:
In live mode, press to begin sequential switching of the live cameras. The view will rotate through
all cameras following the programmed dwell time.
In SD card backup mode, press to save the desired still image to SD card.
T-rec Indicator:
This indicator LED will turn ON to signal that the schedule/timer record setting is enabled.
A-rec Indicator:
This indicator LED will turn ON to signal that the alarm record setting is enabled.
DISK Indicator:
The indicator shows the operation status of the unit’s hard-disk drives. The green light indicates
the hard-disk drive is storing or retrieving data. The red light signals the hard-disk drive is filling
up. The orange light indicates the hard disk is retrieving at disk-full status.
Shuttle Ring:
The shuttle ring is used to playback video at different speeds in forward or reverse. Turning the
shuttle ring to the left will play recorded video in reverse, turning the shuttle ring to the right will
play the video at different speeds in the forward direction.

8
Jog Dial:
The Jog Dial can be used to step frame by frame in the forward or reverse direction.
SD CARD Slot:
This is used for system software updating and archiving/accessing critical images.
Mobile Rack Power LED:
Indicates the power status of the Mobile Rack. The green light indicates the Mobile Rack is
activate.
Mobile Rack HDD LED:
Indicates the HDD status of the Mobile Rack. The orange light indicates the HDD is storing or
retrieving data.

9
2.2 Rear View
RS-232
ALARM DC12V
RS-485
hi-z
75
AUDIO
IN
IN
OUT
OUT
MONITOR
CH1 CH2 CH3 CH4
ETHERNET
I/O
25
31 32 33
26 28
29 30 34 35 36 37
VIDEO IN Connector:These 4 BNC connectors are used to connect the video output from a camera
Hi-Z/75 ΩIndividual termination: These 4 switches are used to set the impedance of each loop
between 75Ωand Hi-Z.
RS-232 Port:The RS-232 communication port functions as a connector to an external control device.
Please refer to RS-232 & RS-485 Protocol for more details.
MONITOR Connector:The connector provides the unit’s composite video or a live signal if connected
to a display device.
AUDIO OUT: This provides the unit’s audio signal to a speaker.
AUDIO IN Connector: This connector is used to connect the audio output from a camera or other
devices to the DVR.
ETHERNET 10/100 Connector:This is one standard RJ-45 connector for 10/100 Mbps Ethernet
networks.
RS-485 Port:The RS-485 communication ports function as connectors when two or more units are
serially connected to expand the storage capacity.
ALARM I/O: This is a 9-PIN D-SUB connector including SWITCH OUT, GROUND, ALARM OUT, DISK
FULL, RECORD IN, ALARM RESET, and ALARM IN for connecting with external devices. Please
refer to the next section for details.
Wire Catch: The wire catch secures the power cord and keeps it in place (so that it does not droop or
hang loosely).
Ground Screw’s: The ground screw is for chassis terminal.
DC Power Jack: The inlet connects to the external power supply. 12 VDC, 5A UL Listed Class 2
Power Supply.

10
2.3 ALARM In/Out
ALARM1 IN ALARM4 IN
ALARM2 IN ALARM3 IN
ALARM OUT
RECORD IN GROUND
DISK FULL
ALARM RESET
12345
6789
THIS FIGURE IS LOOKED FROM THE REAR VIEW
1. GND: Ground Contact.
2. ALARM OUT (OUTPUT): This is a common alarm output trigger. Connect this to external
devices such as buzzers or lights. Switches Low (GND) (
5V
0V(Active)
)
3. DISK FULL (OUTPUT): This is a disk full output trigger. Connect this to external devices such
as buzzers or lights. Switches Low (GND) (
5V
0V(Active)
)
4. ALARM RESET (INPUT): This pin connects to an alarm-clear device for clearing an alarm. Use
a Normally Open switch to GND. (
5V
0V(Active)
)
5. RECORD IN (INPUT): This pin connects to a record trigger device for starting a record.
Negative Trigger. (
5V
0V(Active)
)
6. ALARM4 IN (INPUT): This is an alarm input (for CH 4 ), which can be programmed in the menu
system to Normally Open or Normally Closed operation.
7. ALARM3 IN (INPUT): same as the above, for CH 3
8. ALARM2 IN (INPUT): same as the above, for CH 2
9. ALARM1 IN (INPUT): same as the above, for CH 1

11
3. INSTALLATION
Please follow the instructions and the diagram below to set up the system.
3.1 Basic Connection
CONNECTING WITH 1 to 4 CAMERAS
Camera
Monitor
Camera
Camera
Camera
RS-232
ALARM DC12V
RS-485
hi-z
75
AUDIO
IN
IN
OUT
OUT
MONITOR
ETHERNET
I/O
ATTACHING AN EXTERNAL DEVICE TO DVR
Connect an alarm out, alarm input, and a peripheral device as shown in the diagram below.
Alarm In -> Alarm1 In, Alarm2 In, Alarm3 In, Alarm4 In
RS-232
ALARM DC12V
RS-485
hi-z
75
AUDIO
IN
IN
OUT
OUT
MONITOR
ETHERNET
I/O
12345
6789
Alarm Reset
(Normally Open)
(Normally Open)
Alarm1 in
(Normally Open)
Alarm2 in
(Normally Open)
Alarm3 in
(Normally Open)
Alarm4 in
Ground
Trigger Out

12
3.2 Hard-Disk Drive Installation
The DVR is capable of supporting two hard drives - One internal drive (from factory) and one hot
swappable mobile drive (factory option). The internal HDD (compartment HD1), is default-configured as
a master. If adding an additional HDD to the Mobile Rack (compartment HD2), please set to Master
and follow the install instructions in section . arrangement of installed hard-disk drives for the system
(Table 3.2 A.) is shown in the tables below.
Table 3.2 A. The jumper settings of hard disk drives in the system
Location Jumper
IDE 1 Compartment HD 1 Master (Default)
IDE 2 Compartment HD 2 Master
Table 3.2 B. Compatible hard-disk drives
Manufacturer Model Capacity Rotation
WD800AB 80GB 5400 RPM
WD1200AB 120GB 5400 RPM
WD800BB 80GB 7200 RPM
WD1200BB 120GB 7200 RPM
Western Digital
WD1800BB 180GB 7200 RPM
ST380020A/P 80GB 5400 RPM
Seagate
ST340810A/P 40GB 5400 RPM
4A160J0-1A 160GB 5400 RPM
4R080L0-1 80GB 5400 RPM
6Y120L0-1 120GB 7200 RPM
6Y200P0-1A 200GB 7200 RPM
Maxtor
6Y250P0-1A 250GB 7200 RPM
NOTE: Hard-disk drives not shown on this list have not been tested by the engineering team
and are not recommended for use with this product. For the latest updated list on the
recommended hard disk drives, please contact your dealers or distributors.

13
3.3 System Information and channel selection
3.3.1 SYSTEM INFORMATION
You can display system settings information as shown on Figure 3.3 A below at any time by pressing
the Display button . In the playback mode, the recorded video information is displayed. In the live or
recording mode, the Manual Recording information is displayed. Each sequential press of the Display
button displays a different message detailed in the following example. By default, the unit displays
titles, time, date, and an indicating bar of capacity status on a monitor as shown next.
Default display
CH1 , CH2, CH3, CH4 are titles for each channel, changeable in Setup menu
Capacity Status :
09- 05-2003 16:13:02
( System Data/ Time )
Press the Display button once; the DVR will display the following sample message plus the default
display. Press the Display button again; the unit will not display any OSD message. Press the
button one more time to back to the default display.
CH1 CH2
CH3 CH4

14
Figure 3.3 A. Description of Figure 3.3 A
(1+2: 59G): Total capacity of installed hard disks, 59 GB (in this
example)
(12.4 HR): Total 12.4 hour recording time available
(
): Timer record activated
(
): Alarm record activated
(QUALITY: BEST): Record quality setting, BEST
(NTSC): NTSC system
(RATE: 6 HR): Setting of Record time mode, 6 hours
(10 F/S): Record speed setting, 10 frames/sec
(): Audio function activated
(): Indicate which HDD is activated
(9K): The image file size
(HD): Hard disk Compartment
(P ): Y Hard disk installed; . No hard disk installed
(SIZE 20G): The capacity of the installed hard disk
(POS): Percentage of system; R: Recording; P: Playback
(IP : 192 . 168 . 1 . 90): Setting of
the Ethernet
communication,192.168.1.90
()
: External signal
( x ): Disk unavailable
3.3.2 Channel Selection
The CH1, CH2, CH3, CH4, Quad ( ), and Seq./Save button are used to select the displayed video
channels and zoom in factor. The following table shows the functions under different mode.
Mode Key Result Display
Quad ( )
CH1/ CH2/ CH3/ CH4 ( Single channel )
Live / Record
Seq./Save
    then loop back
Quad ( )
CH1/ CH2/ CH3/ CH4 ( Single channel )
Playback
The same channel
pressed the 2
nd
time
single channel with 2x2 zoom in
1+ 2: 59G 12.4 HR
QUALITY: BEST NTSC
RATE: 6 HR 10 F/S
9K
HD P SIZE POS
1 Y 20 G 39.5% P
2 Y 39G 0.0%R
IP : 192 . 168 . 1 . 90

15
3.4 Updating System Software
If the system software of the 4CH DVR needs to be upgraded, please take the following steps to safely
update it.
Important: Before carrying out the following procedures, please ensure the SD card is working
and the file of system software is intact
1. Turn off the 4CH DVR.
2. Insert the SD card into the built-in SD slot of the unit.
3. Hold down the Up and Down buttons simultaneously, and then turn on the unit.
4. Keep holding down the buttons until the 4CH DVR sounds a tone and display the message
“ XXXXXX BYTES READ” Now the 4CH DVR is updating the system software, which will take
approximately 90 seconds to process.
5. Restart the unit (by powering down/up completely) when the device sounds a tone twice and displays
the message “ PLEASE RESTART” The process is complete.
(If you have already followed the procedure 1~5. the unit, however, not being able to power on.
Please first check if the SD card you are using is functioning and the file is intact. And then repeat
procedures 1 ~ 5 again.)
6. Verify the version of the system software. (Please refer to section 5.6 VERSION option)
A-rec T-recDISK
Power Search Seq.
/Save
Setup
13 12
EnterDisplay Play Pause Stop
SD Card
Rec
ZOOM
Warning: Don’t Interrupt the process while the unit is updating itself. Doing so could
cause the unit hang/lock-up.

16
4. BASIC OPERATIONS
This section outlines the basic operating instructions for the DGR204.
4.1 Configuring Recording Settings
Recording Time settings (Recording Rate and Picture Quality Setting)
Recording time will vary depending on the image size, recording rate, and the capacity of the hard-disk
drives. Generally, the DVR comes with a built-in hard-disk drive for continuous recording from one to
four weeks under most recording conditions. The table below shows the possible recording times based
on a 80GB hard-disk drive at certain refresh rates and the corresponding image quality.
With one or more hard-disk drive(s) in operation, please calculate the recording time using the table
below in accordance with your requirement. For a NTSC unit, for example, if the unit is set to record
images with BEST quality at a 30 Frame/Sec record rate, normally a 80GB hard-disk drive will be filled
in 15 hours (See the gray area in the table). If a 160GB hard-disk drive is used with the same refresh
rate and picture quality, it will be filled in 30 hours (2 times the rate of a 80GB hard-disk drive).
NTSC (Audio OFF) Possible Recording Time HDD=80GB ( hour )
BEST 15 24 36 60 132 301 590 1024 2905 4352 5799
HIGH 18 29 43 72 152 362 709 1230 3486 5222 6959
STANDARD 22 36 54 90 198 452 886 1537 4358 6528 8698
Image
Quality
BASIC 30 45 68 113 248 565 1108 1921 5448 8160 10873
Refresh Rate (Frame/Sec)
30 15 10 6 2.7 1.2 0.61 0.35 1/8 1/12 1/16
REC Time Mode 2 hr 4 hr 6 hr 12 hr 24 hr 48 hr 96 hr 168 hr 480 hr 720 hr 960 hr
NTSC (Audio ON) Possible Recording Time HDD=80GB ( hour )
BEST - - 36 59 126 271 485 744 - - -
HIGH - - 42 70 150 319 562 846 - - -
STANDARD - - 53 87 185 387 668 981 - - -
Image
Quality
BASIC - - 66 108 228 468 786 1124 - - -
Refresh Rate (Frame/Sec)
30 15 10 6 2.7 1.2 0.61 0.35 1/8 1/12 1/16
REC Time Mode 2 hr 4 hr 6 hr 12 hr 24 hr 48 hr 96 hr 168 hr 480 hr 720 hr 960 hr
PAL (Audio OFF) Possible Recording Time HDD=80GB ( hour )
BEST 3.8 6 9 15 27.1 51.2 99.4 171.8 605.8 907.2 1208.6
HIGH 4.5 7.2 10.8 18 32.5 61.4 119.3 206.1 726.9 1088.6 1450.3
STANDARD 5.7 9 13.5 22.6 40.6 76.8 149.1 257.7 908.7 1360.8 1812.9
Image
Quality
BASIC 7.7 11.4 17.1 28.5 51.3 97 188.4 325.5 1147.8 1718.9 2290.0
Refresh Rate (Frame/Sec)
25 12.5 8.3 5 2.7 1.4 0.76 0.44 1/8 1/12 1/16
REC Time Mode 3 hr 6 hr 9 hr 12 hr 24 hr 48 hr 96 hr 168 hr 480 hr 720 hr 960 hr

17
NOTE 1: Recording times on the tables above are estimated. For actual available
recording time of a recording configuration, please refer to the system
information of the DVR. (Please refer to section 3.3 system information for more
details.)
2: No audio function at the refresh rate in NTSC: 30 frame/sec ~ 15 frame/sec, 1/8
frame/sec ~ 1/16 frame/sec.
No audio function at the refresh rate in PAL: 25 frame/sec ~ 12.5 frame/sec, 1/8
frame/sec ~ 1/16 frame/sec.
PAL (Audio ON) Possible Recording Time HDD=80GB ( hour )
BEST - - 8.9 14.7 26.0 47.6 86.7 137.0 - - -
HIGH - - 10.6 17.6 31.0 56.3 101.4 158.0 - - -
STANDARD - - 13.2 21.8 38.3 69.0 122.2 186.7 - - -
Image
Quality
BASIC - - 16.7 27.4 47.7 84.9 147.4 219.9 - - -
Refresh Rate (Frame/Sec) 25 12.5 8.3 5 2.7 1.4 0.76 0.44 1/8 1/12 1/16
REC Time Mode 3 hr 6 hr 9 hr 12 hr 24 hr 48 hr 96 hr 168 hr 480 hr 720 hr 960 hr

18
4.2 Recording Operations
This section details the various recording methods available – Manual, Timer, Alarm, and External.
Before commencing with the recording function, please configure the recording settings properly
according to your needs.
4.2.1 Manual Recording
When the DVR is in live display mode, take the following steps to start recording:
(1) In live display, press the REC button to record video into a hard disk drive with the
corresponding programmed recording settings. The monitor should display a flashing REC
message and the REC button will light up indicating the DVR is in the recording status.
(2) Press the STOP button to stop recording any time.
(3) To access just recorded video, please refer to section 4.4 for more details.
4.2.2 Timer Recording
Timer recording provides two periods of time each day in a weekly table which programs the DVR
Start and Stop recording at specified times. Please take the following steps to program the
scheduled recording.
(1) Press the Setup button to enter the MAIN MENU.
(2) Select the TIMER/ SEQ/ TITLE and press the Enter button to enter the TIMER/ SEQ/
TITLE page.
(3) Select the TIMER－SET.
(4) Press the Enter button to enter the REC SCHEDULE table.
(5) ●You can set up by using the “<” button and the “>” button to locate the specific
day/hour/minute and use the “^” button and the “v” button to set the
day/hour/minute you wish.
●You can also set up by using the Shuttle Ring and the Jog Dial. is the equal of the
“<” button , is the equal of the “>” button , is the equal of the “^” button
and is the equal of the “v” button .
●The time is displayed in a 24-hour clock format.
(6) After scheduling is completed, press the Enter button and set OK to save the setting or
select CANCEL to leave the page without saving the settings.
(7) To activate the programmed recording schedule, set the REC ENABLE to ON. As the
scheduled recording is on, the red indicator of the Timer Record will be on as well. To
deactivate it, set to OFF.
(8) Press the STOP button during the scheduled recording to stop it at any time. If you wish
to continue the scheduled recording, press the REC button to proceed.

19
NOTE: If a programmed schedule falls within the current set time of the DVR, recording will
begin upon exiting programming.
NOTE: If you activate the recording function before the scheduled recording, the unit will
operate recording as shown in the diagram below and keep those Images in different
files.
03:00 06:00 08:00 12:00 14:00
START END START END
Start Manual
Recording
Timer Manual Timer Manual
NOTE: LIVE images may be frozen. But, it isn't a failure.

20
MAIN MENU
RECORD
ALARM
TIMER/ SEQ/ TITLE
COMMUNICATION
DISK
SYSTEM
GOTO TIMER/SEQ/TITLE PAGE
TIMER/ SEQ/ TITLE
CLOCK : SET
REC ENABLE : OFF
TIMER :SET
SEQUENCER :SET
TITLE :SET
MAIN PAGE
SET REC SCHEDULE
REC SCHEDULE
START END START END
S : 00:00-00:00 00:00-00:00
M: 00:00-00:00 00:00-00:00
T : 00:00-00:00 00:00-00:00
W: 00:00-00:00 00:00-00:00
T : 00:00-00:00 00:00-00:00
F : 00:00-00:00 00:00-00:00
S : 00:00-00:00 00:00-00:00
OK CANCEL
TO MOVE TO CHANGE
MAIN MENU
RECORD
ALARM
TIMER/ SEQ/ TITLE
COMMUNICATION
DISK
SYSTEM
GOTO TIMER/SEQ/TITLE PAGE
TIMER/ SEQ/ TITLE
CLOCK : SET
REC ENABLE : OFF
TIMER : SET
SEQUENCER :SET
TITLE :SET
MAIN PAGE
TIMER REC ENABLE