Digisol DG-CS4616F User manual

DG-CS4616F
GIGA LAYER 3 SWITCH
Installation Guide
V1.0
2018-01-30
As our products undergo continuous development the specifications are subject to change without prior notice

DG-CS4616F Installation Guide
2
Content
Chapter 1 Introduction..................................................................... 1
1.1 Product Brief.................................................................................................1
1.1.1 Introduction........................................................................................................... 1
1.2 Physical Specifications............................................................................. 1
1.3 Description of Hardware............................................................................2
1.3.1 Front Panel............................................................................................................ 2
1.3.2 Back Panel............................................................................................................. 2
1.3.3 Status LEDs...........................................................................................................2
1.3.4 Front Panel Port Description............................................................................3
Chapter 2 Hardware Installation.................................................... 1
2.1 Installation Notice....................................................................................... 1
2.1.1 Environmental Requirements.......................................................................... 1
2.1.2 Installation Notice................................................................................................4
2.1.3 Security Warnings............................................................................................... 5
2.2 Installation Preparation............................................................................. 6
2.2.1 Verify the Package Contents............................................................................ 6
2.2.2 Required Tools and Utilities............................................................................. 6
2.3 Installation Guide........................................................................................ 6
2.3.1 Installing the Switch............................................................................................6
2.3.2 Connecting Console........................................................................................... 7
2.3.3 SFP/SFP+ Transceiver Installation................................................................. 8
2.3.4 Copper Cable/Fiber Cable Connection..........................................................8
2.3.5 Power Supply Connection.................................................................................9
2.3.6 Ground Cable Connection.............................................................................. 10

DG-CS4616F Installation Guide
Chapter 1-1
Chapter 1 Introduction
1.1 Product Brief
DG-CS4616F switch
Fig 1- 1 DG-CS4616F switch
1.1.1 Introduction
DG-CS4616F switch is uplink layer 3 10Gb switch. DG-CS4616F has 16 SFP+ port.
DG-CS4616F switch can serve ideally as distribution layer switch for the 10Gb input
device of campus networks, enterprise networks and IP metropolitan networks.
DG-CS4616F is also used in the Internet bar as the full 10Gb convergence device.
1.2 Physical Specifications
Management Port
1 RJ-45 serial console port
1 RJ-45 management Ethernet interface
1 USB interface which supports USB2.0
AC/DC Power Input
AC: 90 ~ 264VAC, 47 ~ 63Hz
DC: -48VDC, 2.5A
Power Consumption
12W to 24W
Operating Temperature
-5°C ~ 45°C
Storage Temperature
-40°C ~ 70°C
Relative Humidity
5% ~ 95%, no condensate
Dimension
440mm×44mm×240mm (W * H * D)

DG-CS4616F Installation Guide
Chapter 1-2
Weight
About 3.14kg
Mean time between failure
Minimal MTBF: 50,000 hours
1.3 Description of Hardware
1.3.1 Front Panel
DG-CS4616F has 16 10Gb SFP+ ports, 1 Console port, 1 management Ethernet
interface, 1 system reset button, 1 USB interface and 19 LEDs.
The front panel of DG-CS4616F is shown below:
Fig 1- 2 Front Panel of DG-CS4616F
1.3.2 Back Panel
The back panel of DG-CS4616F is shown below, there is a fan, 1 220V AC power
socket, 1 -48V DC power socket and 1 ground screw hole.
Fig 1- 3 Back Panel of DG-CS4616F
1.3.3 Status LEDs
DG-CS4616F switch include port indications, system status indication and fan
indication. Their status meanings are shown below.
1.3.3.1 Port indication Description

DG-CS4616F Installation Guide
Chapter 1-3
Fig 1- 4 DG-CS4616F LED LED diagram
Table 1-1 DG-CS4616F port indications description
Panel Symbol
Status
Description
Port 1-16(Link/Act)
On (Green)
ports are in successful link state
Flash(Green)
ports are in successful link state and
receive/send data
Off
ports are not in link
1.3.3.2 System Status Indication Description
Fig 1- 5 DG-CS4616F diagram
Table 1- 2 system indication description
Panel Symbol
Status
Description
PWR
On (Green)
The internal power is operating normally
Off
Power is off or error
SYS
On (Green)
System is abnormal
Flash (Green)
System is in normal
Off
Power is off or system is abnormal
FAN
On (Red)
Fan is abnormal
Off
Fan is normal
1.3.4 Front Panel Port Description
Each port description is shown below:

DG-CS4616F Installation Guide
Chapter 1-4
Table 1- 3 DG-CS4616F switch port description
Interface mode
Spec
RJ-45 port
10/100/1000Mbps auto negotiation
MDI/MDI-X cable mode auto negotiation
5 kinds of UTP: 100 m
SFP
SFP-SX-L transceiver
1000Base-SX SFP (850nm, MMF, 550m)
SFP-LX-L transceiver
1000Base-LX SFP interface card module (1310nm,
SMF, 10km or MMF, 550m)
SFP-LX-20-L transceiver
1310nm light waves, 9/125um single mode fiber: 20km
SFP-LX-40 transceiver
9/125um single mode fiber: 40km
SFP-LH-70-L transceiver
9/125um single mode fiber: 70km
SFP-LH-120-L transceiver
9/125um single mode fiber: 120km
SFP+
SFPX-SR:
62.5/125um multimode fiber: 32m
50.0/125um,500MHz/km multimode fiber: 85m
50.0/125um,2000MHz/km multimode fiber: 300m
SFPX-LR:
9/125um single mode fiber: 10km
SFPX-ER:
9/125um single mode fiber: 40km
DAC-SFPX
DAC-SFPX-3M
DAC-SFPX-5M
AOC-SFPX
AOC-SFPX-5M
AOC-SFPX-10M

DG-CS4616F Installation Guide
Chapter 2-1
Chapter 2 Hardware Installation
2.1 Installation Notice
To ensure the proper operation of DG-CS4616F and your physical security, please
read carefully the following installation guide.
2.1.1 Environmental Requirements
The switch must be installed in a clean area. Otherwise, the switch may be damaged
by electrostatic adherence.
Maintain the temperature within 0 to 50 °C and the humidity within 5% to 95%,
non-condensing.
The switch must be put in a dry and cool place. Leave sufficient spacing around the
switch for good air circulation.
The switch must work in the right range of power input (AC power: 100~240VAC, 1.0A
(50/60 Hz), DC power: -48~-60VDC, 2.5A)
The switch must be well grounded in order to avoid ESD damage and physical injury
of people.
The switch should avoid the sunlight perpendicular incidence. Keep the switch away
from heat sources and strong electromagnetic interference sources.
The switch must be mounted to a standard 19’’ rack or placed on a clean level
desktop.
2.1.1.1 Dust and Particles
Dust is harmful to the safe operation of DG-CS4616F. Dust can lead to electrostatic
adherence, especially likely under low relative humidity, causing poor contact of metal
connectors or contacts. Electrostatic adherence will result in not only reduced product
lifespan, but also increased chance of communication failures. The recommended value
for dust content and particle diameter in the site is shown below:
Max Diameter (µm)
0.5
1
3
5
Max Density
(particles/m³)
1.4×107
7×105
2.4×105
1.3×105

DG-CS4616F Installation Guide
Chapter 2-2
Table 2- 1Environmental Requirements: Dust
In addition, salt, acid and sulfide in the air are also harmful to the switch. Such
harmful gases will aggravate metal corrosion and the aging of some parts. The site should
avoid harmful gases, such as SO2, H2S, NO2, NH3and Cl2, etc. The table below details the
threshold value.
Gas
Average (mg/m³)
Max (mg/m³)
SO2
0.2
1.5
H2S
0.006
0.03
NO2
0.04
0.15
NH3
0.05
0.15
Cl2
0.01
0.3
Table 2- 2 Environmental Requirements: Particles
2.1.1.2 Temperature and Humidity
The switch install site should maintain a desirable temperature and humidity.
High-humidity conditions can cause electrical resistance degradation or even electric
leakage, degradation of mechanical properties and corrosion of internal components.
Extreme low relative humidity may cause the insulation spacer to contract, making the
fastening screw insecure. Furthermore, in dry environments, static electricity is liable to be
produced and cause harm to internal circuits. Temperature extremes can cause reduced
reliability and premature aging of insulation materials, thus reducing the switch’s working
lifespan. In the hot summer, it is recommended to use air-conditioners to cool down the
site. And the cold winter, it is recommenced to use heaters.
The recommended temperature and humidity is shown below:
Temperature:
Relative humidity
Long term condition
Short term condition
Long term condition
Short term
condition
15 ~ 30°C
0 ~ 50°C
40 ~ 65%
5 ~ 95%
Table 2- 3 Environmental Requirements: Temperature and Humidity

DG-CS4616F Installation Guide
Chapter 2-3
Caution!
A sample of ambient temperature and humidity should be taken at 1.5m above the
floor and 0.4m in front of the switch rack, with no protective panel covering the front and
rear of the rack. Short term working conditions refer to a maximum of 48 hours of
continued operation and an annual cumulative total of less than 15 days. Formidable
operation conditions refers to the ambient temperature and relative humidity value that
may occur during an air-conditioning system failure, and normal operation conditions
should be recovered within 5 hours.
2.1.1.3 Power Supply
It is adopted module switch power for the switch; the input parameter of power is
shown below:
The AC input voltage: 100~240V; 1.0A
The frequency: 50/60Hz
The DC input voltage: -48V~-60V; 2.5A
Before powering on the power supply, please check the power input to ensure proper
grounding of the power supply system. The input source for the switch should be reliable
and secure；a voltage adaptor can be used if necessary. The building’s circuit protection
system should include in the circuit a fuse or circuit-breaker of no greater than 240 V, 10 A.
It is recommended to use a UPS for more reliable power supplying. .
Caution!
Improper power supply system grounding, extreme fluctuation of the input source,
and transients (or spikes) can result in larger error rate, or even hardware damage!
2.1.1.4 Preventing Electrostatic Discharge Damage
Static electric discharges can cause damage to internal circuits, even the entire
switch. Follow these guidelines for avoiding ESD damage:
Ensure proper earth grounding of the device;
Perform regular cleaning to reduce dust;
Maintain proper temperature and humidity;
Always wear an ESD wrist strap and antistatic uniform when in contact with circuit
boards.
2.1.1.5 Anti-interference

DG-CS4616F Installation Guide
Chapter 2-4
All sources of interference, whether from the device/system itself or the outside
environment, will affect operations in various ways, such as capacitive coupling, inductive
coupling, electromagnetic radiation, common impedance (including the grounding system)
and cables/lines (power cables, signal lines, and output lines). The following should be
noted:
Precautions should be taken to prevent power source interruptions;
Provide the system with a dedicated grounding, rather than sharing the grounding
with the electronic equipment or lightning protection devices.
Keep away from high power radio transmitters, radar transmitters, and high frequency
strong circuit devices.
Provide electromagnetic shielding if necessary.
2.1.1.6 Rack Configuration
The dimensions of the DG-CS4616F are designed to be mounted on a standard 19’’
rack. The size is 442.9mm×44mm×230.2mm (W * H * D). Please ensure good ventilation
for the rack.
Every device in the rack will generate heat during operation, therefore vent and fans
must be provided for an enclosed rack, and devices should not be stacked closely.
When mounting devices in an open rack, care should be taken to prevent the rack
frame from obstructing the switch ventilation openings. Be sure to check the
positioning of the switch after installation to avoid the aforementioned.
Caution！
If a standard 19’’ rack is not available, the DG-CS4616F can be placed on a clean
level desktop, leave a clearance of 100mm around the switch for ventilation, and do not
place anything on top of the switch.
2.1.2 Installation Notice
Read through the installation instruction carefully before operating on the system.
Make sure the installation materials and tools are prepared. And make sure the
installation site is well prepared.
During the installation, users must use the brackets and screws provided in the
accessory kit. Users should use the proper tools to perform the installation. Users
should always wear antistatic uniform and ESD wrist straps. Users should use
standard cables and connecters.
After the installation, users should clean the site. Before powering on the switch,

DG-CS4616F Installation Guide
Chapter 2-5
users should ensure the switch is well grounded. Users should maintain the switch
regularly to extend the lifespan of the switch.
2.1.3 Security Warnings
When using SFP/SFP+ transceiver, do not stare directly at the fiber bore when the
switch is in operation. Otherwise the laser may hurt your eyes.
Do not attempt to conduct the operations which can damage the switch or which can
cause physical injury.
Do not install, move or disclose the switch and its modules when the switch is in
operation.
Do not open the switch shell.
Do not drop metals into the switch. It can cause short-circuit.
Do not touch the power plug and power socket.
Do not place the tinder near the switch.
Do not configure the switch alone in a dangerous situation,
Use standard power sockets which have overload and leakage protection.
Inspect and maintain the site and the switch regularly.
Have the emergence power switch on the site. In case of emergence, switch off the
power immediately.
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not
the class B ITE limits. The following warning shall be included in the instructions for
use:
Warning
This is class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Caution!
Potential risk include: Electric leakage, Power supply arcing, Power line breakage,
Imperfect earth, Overload circuit and Electrical short circuit. If electric shock, fire, electrical
short circuit occurs, please cut off the electricity supply and alarm rapidly. Rescue the
injured person in the contingency under inherently safe, Give the injured person proper
first aid treatment according to the injury state, and seek help from the Medical
Emergency using various ways

DG-CS4616F Installation Guide
Chapter 2-6
2.2 Installation Preparation
2.2.1 Verify the Package Contents
First, open the package; please check the contents of the switch container and
accessory kit. (If you are concerned that any item is missing or an incorrect item has been
supplied, please contact your dealer as soon as possible.)
2.2.2 Required Tools and Utilities
The required tools and utilities are shown below:
Cross screwdrivers
Flat-blade screwdriver
ESD wrist strap
Antistatic uniform
Caution!
Users should prepare the required tools and utilities by themselves.
2.3 Installation Guide
2.3.1 Installing the Switch
Please mount DG-CS4616F switch as below:
1. Attach the 2 brackets on the DG-CS4616F with screws provided in the accessory
kit.
Fig 2- 1 Fasten the Brackets to the Switch

DG-CS4616F Installation Guide
Chapter 2-7
2. Put the bracket-mounted switch smoothly into a standard 19’’ rack. Fasten the
DG-CS4616F to the rack with the screws provided. Leave enough space around the
switch for good air circulation.
Fig 2- 2 Fasten the Switch to the Rack
Caution!
The brackets are used to fix the switch on the rack. They can’t serve as a bearing.
Please place a rack shelf under the switch. Do not place anything on top of the switch. Do
not block the blowholes on the switch to ensure the proper operation of the switch.
2.3.2 Connecting Console
DG-CS4616F provide a serial RJ45 console port.

DG-CS4616F Installation Guide
Chapter 2-8
Fig 2- 3 Connecting Console to switch
The connection procedure is listed below:
1. Find the console cable provided in the accessory kit. Attach the RJ45 end to console
port of the switch.
2. Connect the other side of the console cable to a character terminal (PC).
3. Power on the switch and the character terminal. Configure the switch through the
character terminal.
2.3.3 SFP/SFP+ Transceiver Installation
DG-CS4616F has multiple 10Gb interfaces and provides multiple 1000Mb SFP or 10Gb
SFP+ transceiver slots.
The procedure for installing the SFP/SFP+ transceiver is shown below:
Step 1: Put on a ESD wrist strap (or antistatic gloves)
Step 2: Insert the SFP/SFP+ transceiver to the guide rail inside the fiber interface line card.
Do not put the SFP/SFP+ transceiver up-side-down.
Step 3: Push the SFP/SFP+ transceiver along the guide rail gently until you feel the
transceiver snap into place at the bottom of the line card.
Note: the SFP/SFP+ transceiver is hot swappable.
Caution!
Do not stare directly at the 2 fiber bore in the SFP/SFP+ transceiver when the switch is in
operation, otherwise the laser may hurt your eyes.
2.3.4 Copper Cable/Fiber Cable Connection
Copper cables should be connected as below:
Step 1: Insert one end of the Ethernet cable to the RJ-45 Ethernet port in the switch
copper cable line card;
Step 2: Insert the other end of the Ethernet cable to the RJ-45 Ethernet port of some other
device;
Step 3: Check all status indicators for the corresponding ports; a lighted LED indicates
that the link has been established, otherwise the link is not ready and the cable should be

DG-CS4616F Installation Guide
Chapter 2-9
examined.
Caution!
Please verify the sign above the port to ensure using the right port. Connecting to wrong
ports might damage the switch.
Fiber cables should be connected as below:
Step 1: remove the protective plug from the SFP/SFP+ fiber transceiver bore; Remove the
protective cap from one end of the fiber cable. Keep the fiber end clean and neat.
Step 2: Attach one end of the fiber cable to the SFP/SFP+ transceiver, and attach the
other end to the transceiver of the other devices. Note: SFP/SFP+ transceiver’s TX port
should be connected to RX port of other device, and SFP/SFP+ transceiver’s RX port
should be connected to TX port of other device.
Step 3: Check the fiber port status indicator, a light LED indicates that the link has been
established; otherwise the link is not ready and should be examined.
Caution!
Please verify the sign above the port to ensure using the other ports. Connecting to wrong
ports might damage the transceiver or the other ports. When connecting other devices
through a fiber cable to the switch, the output power of the fiber cable must not exceed the
maximum received power of the corresponding modules. Otherwise, it will damage the
fiber transceiver. Do not stare at the fiber bore when the switch is in operation. That may
hurt your eyes.
2.3.5 Power Supply Connection
DG-CS4616F uses 220V AC power. Please read the power input specification for the
detailed information.
Power supply connection procedure is described as below:

DG-CS4616F Installation Guide
Chapter 2-10
Fig 2- 4 Attaching power cable to DG-CS4616F
1. Insert one end of the power cable provided in the accessory kit into the power source
socket (with overload and leakage protection), and the other end to the power socket in
the back panel of the switch.
2. Check the power status indicator in the front panel of the switch. The corresponding
power indicator should light. DG-CS4616F is self-adjustable for the input voltage. As soon
as the input voltage is in the range printed on the switch surface, the switch can operate
correctly.
3. When the switch is powered on, it executes self-test procedure and startups.
Caution!
The input voltage must be within the required range, otherwise the switch can be
damaged or malfunction. Do not open the switch shell without permission. It can cause
physical injury.
2.3.6 Ground Cable Connection
Grounding: The chassis of the equipment must be grounded properly so that the
lightning can flow to the ground, which improves the capability of the chassis for resisting
the electromagnetic interference.
1. Ensure that the grounding cable is connected correctly so that the equipment is
protected against lightning and interference. The correct connection of the grounding
cable is an important measure to ensure the human safety.
2. Connect the chassis to the ground by using a grounding cable. The grounding
resistance must be smaller than 0.10 ohms and the gauge of the grounding cable must be
greater than 10 AWG and the length is 50 cm.

DG-CS4616F Installation Guide
Chapter 2-11
3. Installation steps:
Step 1: Ensure the power switch is set to the off position.
Step 2: Use the screwdriver to turn the screws on the earth ground screw point.
Step 3: Strip one end of the ground wire to the ground hole of system.
Step 4: Connect the other end of the ground wire to a suitable grounding point of building
at your side.
Figure 2- 5 the grounding points