Digisol DG-GS1016D-A User manual

V1.1
2018-05-21
16 Port 10/100/1000Mbps Gigabit
DG-GS1016D-A
PORTS
2000 Mbps
16
Ethernet Unmanaged Switch

Copyright 2018 by DIGISOL SYSTEMS LTD. All rights reserved.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without
written consent from the company.
Trademarks:
TM
DIGISOL is a trademark of DIGISOL SYSTEMS LTD. All other trademarks
are the property of the respective manufacturers.
Copyright

Package Contents
The DG-GS1016D-A is a 10/100/1000Mbps Ethernet unmanaged switch. It
is designed to enhance network performance in a compact form factor. The
switch comes with 16x10/100/1000Mbps ports, offering solutions for
accelerating bandwidth needs of small Ethernet workgroups. The switch
uses store and forward packet-switching technology which offers reliable
data transfer and supports automatic MDI/MDI-X detection & auto
crossover for uplink ports which eliminates the need for cross over cables or
dedicated uplink ports. Any port can simply plug to a server or a switch, using
the usual straight through twisted-pair cable. This switch is ideal for network
connectivity for the SOHO/SME environment.
The following items should be present in your package:
DG-GS1016D-A Gigabit Ethernet Unmanaged Switch
DC Power Adapter (1 No.)
Quick installation guide
Make sure that the package contains above items. If any of the listed items is
damaged or missing, please contact your retailer immediately.
Product Overview
Product Features
Sixteen (16) RJ-45 Ports for 10BaseT,100BaseTX and 1000BaseT
connectivity.
Complies with IEEE802.3, IEEE802.3u and IEEE802.3ab standards.
Supports IEEE802.3x flow control for Full-duplex Mode and
backpressure for Half-duplex Mode.
Supports MDI/MDI-X auto crossover for each port.
Link & activity indicators for each port.
Supports Auto-Negotiation.
MAC Address Table: 8K

After installing the switch, you can check its status from the LED indicators on
the front panel shown below.
Network card for each PC or Server
Network cables min. Cat.5E UTP/STP for 1000Mbps
System Requirements
The following system requirements are recommended
Front View
LED Description
Following is the LED description:
Rear View
Ports 1 ~ 16: The switch has 16 x 10/100/1000Mbps ports for connecting
PC/Desktop or other network devices.
Power Switch is powered on.
LED Description
Port 1 - Port 16
(Link/Act)
OFF
ON (Steady Green)
Status
Switch is powered off.
ON (Steady Green)
Blinking Data packets transmitted/received.
A valid link is established.
OFF No link is established

Power Connection
Connecting Computers to the Switch
The switch features auto MDI/MDIX cross over detection function and
provides plug-and-play capability. Users can immediately use any of the
features of this product simply by plugging the network cables (RJ-45) into
the computers and the switch.
Uplink
All Ports can be used as an uplink port for connecting to another unit without
using crossover cable. When using the uplink port, you can extend the
distance to 100m for linking another switch or hub.
To prolong the operational life of your units
Do not place objects on top of any unit or stack.
Do not obstruct any vents at the sides of the case.
Plug the circle end of the power adapter firmly into the power port on the rear
side, and the other end into an electrical service outlet, then the device is
ready to use.

Limited Lifetime Warranty
[email protected]
1800 209 3444

Digisol is a Subsidiary of Smartlink Holdings Limited
www.digisol.com
1800 209 3444
[email protected]
[email protected]
L-7, Verna Industrial Estate,
Salcete, GOA - 403722
DIGISOL SYSTEMS LIMITED