Digisol DG-GS1510HPEV2 User manual

DG-GS1510HPEV2 Use
r
Manual
DG-GS1510HPEV2
8 PORTS GIGA POE L2 SWITCH WITH 2 SFP PORTS
User Manual
V1.0
2016-08-18
1

DG-GS1510HPEV2 Use
r
Manual
As our products undergo continuous development the specifications are subject to change without prior notice

Web Management User Guide
COPYRIGHT
Copyright 2016 by Smartlink Network Systems Ltd. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of this company.
This company makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Any software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not this company, its distributor,
or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software. Further, this company reserves the
right to revise this publication and to make changes from time to time in the contents thereof without
obligation to notify any person of such revision orchanges.
Trademarks:
DIGISOL™ is a trademark of Smartlink Network Systems Ltd. All other trademarks are the property
of the respective manufacturers.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacturer must
therefore be allowed at all times to ensure the safe use of the equipment.

Web Management User Guide
Table of Contents
Contents
Chapter 1、WEB page introduction.............................................................................................. 2
1、Login dialog Box..............................................................................................................2
2、Main Page.........................................................................................................................3
3、System Configuration.......................................................................................................3
4、Port Configuration..........................................................................................................10
5、MAC binding..................................................................................................................18
6、MAC filtering................................................................................................................. 20
7、VLAN Configuration..................................................................................................... 21
8、SNMP Configuration......................................................................................................24
9、ACL Configuraion..........................................................................................................25
10、QoS Configuration....................................................................................................... 31
11、IP Basic Configuration................................................................................................. 32
12、Certification. Authorization. Accounting (AAA) configuration...................................35
13、PoE port configuration................................................................................................. 39

2
DG-GS1510HPEV2 User Manual
WEB Configuration operating manual
This manual focuses on describing the WEB page of the switch. The user can manage the switch through
WEB page. This manual only introduces the simple operations of the various WEB pages of the various
switches.
Chapter 1、WEB page introduction
Switch WEB pages are organized into groups, each including one or more of the WEB
pages. The following are introduced one by one on each page.
1、Login dialog Box
Figure 1 WEB browsing session of the login page
Figure 1 shows the login dialog box, the logon dialog box will be displayed while the user enters the web
page at the first time.(default IP address is 192.168.0.1/24). When the user fills out the correct user name and

Web Management User Guide
3
password, then clicks the Enter button, can log on to the switch Web server. Passwords are case-sensitive, the
anonymous user password can be a maximum of up to 16 characters, while the multi-user name and password
can be set up to 11 characters. Switch switch default user name is the anonymous user name admin, default
password for the anonymous user's password, the anonymous user's password is empty by default.
2、Main Page
Figure 2 shows the WEB main page of Switch. This page will be displayed after the user logs in the web
page.
Figure 2 Switch switches main page
3、System Configuration:
（1）
Basic information page

Web Management User Guide
4
Figure 3 is the basic configuration page, users can configure the basic information for the switch.
System Description displays the description of the relevant parameters of system.
System descriptor ID displays system in the network identity management.
The system version number displays the current software version number of switches.
The system start-up time displays switch’s time from switch start to the present time.
The system name is the switch’s system name in the network, the user can modify the system name.
The system location is the switch’s physical location in the network, the user can modify the system
location.
System Contact shows the contact person and details of the current node, the user can modify the system
contact.
Figure.3 Basic information Page
（2）
Serial port information pa
g
e
Figure 4 is a serial port configuration page, this page displays serial baud rate and other related
information. When the host,through the serial port terminals (such as Windows, HyperTerminal), connects to
switches then COM port configuration must be consistent with this page information.

Web Management User Guide
5
Figure 4 Serial port information page
（3）
User management page
Figure 5 is a user management page, the user can modify this switch anonymous user’s (admin)
password. Both Telnet, console use the same anonymous user's password. Passwords are case-sensitive, and
can be up to 16 characters. If you want to change your password, the user needs to enter the new password
twice, once the user clicks the apply button, the new password is activated, then if the switch is not enabled
multi-user, will display the login dialog box , require the user to re - login the web page, with a new anonymous
user password.

Web Management User Guide
6
Figure 5 user’s management page
（4）
Securit
y
Mana
g
ement Pa
g
e
Figure 6 is Security management configuration page. Using this configuration, , the administrator can
control network management services like TELNET, WEB and SNMP. You can switch on (enable) or off
(disable) this service. Also these services can be mapped with standards IP ACL group ,and the
implementation of the source IP address control, control access to the host of these services.
When the Switch default services TELNET, WEB and SNMP are open and no ACL filtering, then all hosts
have access to the switch using these three services. If the administrator for security, does not want to provide
oneormoreservices,itcanbeshutdown.

Web Management User Guide
7
Figure 6 Security management page
（5）
Confi
g
ure the current pa
g
e
Figure 7 is the current configuration page. the user can view the current configuration of the switch on this
page. Save button is to store the current system configuration in the configuration file. Because the storage
operation requires erasing & writing into the FLASH memory, it may take up some time. When the user was
configures the switch and restarts it after saving, then configurations are not lost.

Web Management User Guide
8
Figure 7 the current configuration page
（6）
Confi
g
uration pa
g
e
Figure 8 is profile configuration page. This page allows users to view the system’s initial configuration. The
initial configuration is actually the configuration file in the FLASH. When the configuration file does not exist in
FLASH, the system starts using the default configuration. You can use Delete key to delete the configuration
file in the FLASH. Click the Delete button, will pop up a dialog box ,that will prompt the user to make sure to
delete the configuration file or not, otherwise click Cancel button. Download button is used to download a
configuration file to the PC. After clicking download button, will pop up a dialog box, users select Save and
save the configuration file directory path. The downloaded configuration files’ names are in the format
“switch.cfg”.
Figure8 Configuration file page
（7）
File upload pa
g
e
Figure 9 is a file upload page, through this page a user can upload a configuration file and mapping files to
the switch. Click the Browse button to select the upload configuration file or image file in the directory path on

9
Web Management User Guide
the PC. Click Upload button to upload a configuration file or image file, configuration file extension must be *.
cfg, image file must be provided by DIGISOL and the file name extension must be *. img. Before the system
automatically returns to the results page, please do not click on other pages, or restart the switch; otherwise,
the file transfer will lead to failure causing system crash.
Figure 9 File Upload Page
（8） System reset page
Figure 10. is system reset page. Through this page, users can restart the switch. When you click on
Restart button, it will pop up a dialog box that prompts the user to determine whether to restart the switch.

Web Management User Guide
10
Figure10. System reset page
4、Port Configuration
（1）
Port configuration page
Figure 11 is the port configuration page. Users can enable or disable the port, set the port speed, or View
basic information of all ports.
To set a specific port, users need to select the appropriate port name from port drop-down menu,. The
default port status is up. The drop-down menu can select “down” to disable the port. Users can also choose to
set the speed from drop-down menu to set the speed of the port, On this page the user can also view the port’s
other basic information.

Web Management User Guide
11
Figure 11 port configuration and port - display page
（2）
Port Statistics Page
Figure 12 is the port statistics information page. To view a particular port, users need to select the
appropriate port name in the port drop-down menu. Users can view the statistics regarding the number of
packets sent and received on this page.

Web Management User Guide
12
Figure 12 Port Statistics Page
（3）
Flow control page
Figure 13 is the flow control page. Users can enable and disable each port’s send and receive flow control
through this page.

Web Management User Guide
13
Figure 13 Flow control page
（4）
Broadcast storm control pa
g
e
Figure 14 is the Broadcast Storm Control page. This page is used to do the suppression for configure port
broadcast packets, multicast packets and DLF packet.

Web Management User Guide
14
Figure 14 Broadcast Storm control Page
（5）
Port speed limits pa
g
e
Figure 15 is the port speed- limit page. This page is used to configure the port’s transmit and
receive rate.
From the Port drop-down bar select the relevant ports. Bandwidth control of the send datapackets is used
to configure and display the bandwidth control it. If the port is not configured for bandwidth control, it is shown
as off. Cancel button is used to cancel the corresponding data packet to send bandwidth control. Receiving
data packets is used to configure and display the bandwidth control of receive data packets control ,the range
is 1-1024000kbits, enter into force after the key press applications. If the port is not configured bandwidth
control, shown as off. Cancel button is used to cancel the corresponding receiving data packets bandwidth
control.

Web Management User Guide
15
Figure 15 Port speed limit page
（6）
Port protection pa
g
e
Figure 16 is the Port protection page. This page is used to configure the port for the protection port.
If the port is configured as a protected port, the ports cannot exchange data with other Protected port.
Figure 16 protected port page

Web Management User Guide
16
（7） Port Learning restrict page
Figure 17 is the port learning restrict page. This page is used to restrict the number of MAC addresses a
port can learn. The range is 0-8191. The default value is 8191, also is the maximum that the port is not
configured the restrict learning.
Figure 17 Port Learning page
（8） Port Trunking configuration page
Figure 18 is the port trunking configuration page,. This page allows the user to configure the port trunking.
This page consists of four parts: Port trunking ID selection, Port trunking method selection, Configurable ports
and group members port.
To create or modify the port trunking, the user need to select a port trunking ID, port trunking ID from 1 to 3.
The user clicks the list box the appropriate port trunking ID, the port trunking of information is displayed in the
group port. To create a Trunk group, select the appropriate ID in the port trunking ID, click the button "Trunk ID
Settings." To set the port trunking method, select one port trunking method, click the button "polymerization
Settings."Toincreasethetrunkingports,theportcanbeconfiguredtoselectthetrunkingportinthe
configurable, click on "members of the port =" "key. Aggregation from the existing port to remove a port group
member ports in the trunking port selected, click on "non-member port" = "key. To delete the entire TRUNK
group, then click the "Delete trunk group" button.

Web Management User Guide
17
In page configuring process, if at least one Trunk has been established then polymerization settings can
take effect; configured Trunking method is also applied to all on the Trunk groups; in that already exist on the
Trunk can add or remove Port members ; You can only delete the Trunk group when it doesn’t have any
member ports.
Switch supports maximum 3 groups port trunking. Trunk1 and Trunk2 can not used for trunking Gigabit
ports, and each group can be aggregated up to the four same attributes port. Trunk3 can only aggregate
Gigabit ports, and up to 2 Gigabit ports can be aggregated. Port aggregation method is common to all of the
Trunk.
Figure 18 Port Trunking configuration page
（9）
Port mirroring configuration page
Figure 19 is the port mirroring configuration page. This page allows users to configure port mirroring. Port
mirroring through the mirror port is used to monitor the data packets of port. Mirroring Port can only choose one,
being mirrored output port and being mirrored(monitor port) port can select multiple. This page consists of
four components: monitor port, configurable port, monitoring direction and mirror configuration information.
When you start to configure a mirror port ,firstly configured mirroring port from monitor ports, mirror ports can
only have one, and then select the mirror port from the configurable port, select the monitor direction, and