Digital Watchdog C235T Series User manual

C235T Series
About manual
INSTRUCTION MANUAL
PRECAUTIONS
■Do not open or modify
Do not o
p
en the case exce
p
t durin
g
maintenance and installation,
Before installing the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
5436 W Crenshaw Street
Tampa, FL 33634
www.digital-watchdog.com
Technical Support : 1-866-446-3595 / 813-888-9555
■Do not open or modify
Do not open the case except during maintenance and installation,
as it may be dangerous and may damage the product.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances
enter the camera as it can cause fire, short-circuits, or permanent
damage.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to
strong shock or vibration
■Install away from electric or magnetic fields.
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing on the ceiling in a kitchen or boiler
room, as the temperature may damage the camera.
■Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth
moistened with a soft detergent solution.
■Mounting Surface
The mounting surface must be strong enough to support
the camera.
Before installing the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
5436 W Crenshaw Street
Tampa, FL 33634
www.digital-watchdog.com
Technical Support : 1-866-446-3595 / 813-888-9555

TROUBLESHOOTING
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your service
center.
■If no image appears
Is the coaxial cable attached securely?
Is the power and voltage within operational specification?
Has the iris of the lens been adjusted correctly (within specification
levels?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
image. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

DIMENSION (mm)
CONNECTION
*BNC / TERMINAL
*A-Iris socket
Connect the coaxial cable(with pre-wired BNC plug) to the BNC
connector (Video) of the camera.
If you are using an automatic iris lens with the camera, the lens
has to be connected to the A-Iris socket of the camera. If you
are using a lens with manual or fixed iris, this socket is not
used.
The operating voltage is either connected to the designated
terminal block (12V/DC,24V/AC). Operation of the camera will
be confirmed by the power LED at the rear side of the camera
Video Driven (VIDEO)
1.+8,5 VDC
2.NC
3.Video signal
4.GND
DC Driven (DC)
1.control –
2.control +
3.drive +
4.GND

*Adjustment of Back Focus
ADJUSTMENT
ADJUSTMENT
Focus
Zoo
Lbf
1. Please check the lens to see if it is a C mount or CS mount.
To use C mount lens', please fix the lens into front camera after
mounting included C ring to lens.
To use CS mount lens, please fix the lens directly into front
camera
3. Please tighten the focus lever after the adjustment in order to
prevent being out of focus.
2. To adjust the focus, slide the focus lever on the side of the front
camera. In case of the vari focal lens, adjust the focus lever where the
lens is focused in focusing position "wide" and "tele"
Focus adjustment
ADJUSTMENT
*Adjustment of DC Lenses
Focus
Zoo
Lbf
1. Please check the lens to see if it is a C mount or CS mount.
To use C mount lens', please fix the lens into front camera after
mounting included C ring to lens.
To use CS mount lens, please fix the lens directly into front
camera
3. Please tighten the focus lever after the adjustment in order to
prevent being out of focus.
2. To adjust the focus, slide the focus lever on the side of the front
camera. In case of the vari focal lens, adjust the focus lever where the
lens is focused in focusing position "wide" and "tele"
Focus adjustment
To adjust a lens with automatic iris (DC driven) to the camera, please
proceed as follows:
1. Turn the Level potentiometer to the max. position H
(
turn ri
g
ht
)
.
The monitor picture then appears to be too bright.
2. Slowly turn the Level potentiometer back until the monitor picture
appears to be perfect and is not too bright. Then turn the
potentiometer back to the right (in direction ”H”) just a little bit.
3. Check the lens performance by using the camera under changing
lighting conditions.

CAMERA SETTING
C235T Series WDR Color Box Camera
OSD KEY & LED
RS485
NTSC/PAL SWITCH
VIDEO
TERMINAL BLOCK(POWER INPUT)

OSD MENU - C235T
■OSD MENU CONTROL
• CENTER KEY - Used to access menu mode, Also used
to confirm the setting
• UP/DOWN KEY - Used to choose the desired menu
selection.
• LEFT/RIGHT KEY - Used to choose the desired menu
feature adjustment.
■OSD MENU ENTER/EXIT
A. OSD MENU ENTER
• Pushing Center Key for 3 seconds.
B. OSD MENU EXIT
• Press EXIT Menu from Main Menu
• If Pressing Set Key for 3 seconds from Main Menu appears
In this case, just press Set Key.
C. 'SAVE' and 'QUIT'
• Left or Right Key - Selecting Menu
• Up or Down Key - Returning to Menu
1. Press the SET key to access the main setup mode.
2. Select the desired feature using the UP or Down key.
3. Change the status of the selected feature using the LEFT
or RIGHT key.

■MAIN MENU
A. SETUP ID
• DISPLAY ID
- ON :The ID name will displayed in the monitor.
- OFF : The name will not displayed in the monitor.
• CAMERA ID : You can be written to 12 characteristic.
• ID POSITION : Select on screen position of
the camera ID.
B. LENS
• MANUAL : Use for Manual lens'.
• DC : You can control the brightness of the screen and
adjust the desired DC level from 10 to -40.
C. WDR
•EXPO(EXPOSURE): This will lightening or
darkening the picture
•WDR (Wide Dynamic Range) : You can adjust
the desired WDR level from 20 to -20.
D. WB CONTROL
• ATW (Auto Tracking White Balance) : The camera will
automatically control the white balance in any environment.
• AWB (Auto White Balance) : The white balance is
automatically adjusted in a specific environment.
• MANUAL : Users can adjust the colors by adding or
reducing the WB level. You can adjust the desired
WB level from 2,500K to 9,500K

E. AGC
• ON : Activate automatic gain control feature.
You can adjust the desired AGC level from 0 to 38dB.
• OFF : Deactivate automatic gain control feature.
F. LOW LIGHT
• SLOW SHUTTER : Control Image brightness by adjusting
shutter speed
- AGC : shutter speed setting( Range 28 to 48)
- MAX FIELD : Shutter open from Min. x2 to Max. x32
filed accumulation period.
• B&W SS (Black and White Slow Shutter)
• GAIN : To achieve a brighter picture.
G. SYNC
• INTERNAL : Internal synchronization
• LINE LOCK : Phase adjustment may be necessary in
multiple camera installations to prevent picture roll
when switching between cameras

H.RS485
• CAMERA # : Selectable from 1 to 255
(Note : Pelco D is the default)
I. DAY/NIGHT
• AUTO : For automatic switchover from day mode to night mode
( Note : This setting is dependent on the AGC setting.)
• B/W : To keep a B/W image at all times
• COLOR : To keep a color image at all times
• CDS : external input signal control
J. EXIT MENU
• EXIT NO CHANGES : No change
• SAVE NEW AND EXIT : Save change
• RESTORE FACTORY SETTINGS : Factory default
• SW REV
K. PREVIOUS PAGE
• PREVIOUS PAGE : Return page

WARRANTY INFORMATION
Digital Watchdog (referred to as “the Warrantor”) warrants the Camera
Series against defects in materials or workmanship as follows:
LABOR: For the initial five (5) years from the date of original purchase, if the
camera is determined to be defective, the Warrantor will repair or replace
the unit, with new or refurbished product at its option, at no charge.
PARTS: In addition, the Warrantor will supply replacement parts for the
initial five (5) years.
To obtain warranty or out of warranty service, please contact a Technical
Support Representative at 1-866-446-3595 Monday through Friday from
9:00 AM to 5:00 PM Eastern. A purchase receipt or other proof of the date of
the original purchase is required before warranty service is rendered. This
warranty only covers failures due to defects in materials and workmanship
which arise during normal use. This warranty does not cover damage which
occurs in shipment or failures which are caused by products not supplied by
the Warrantor or failures which result from accident, misuse, abuse, neglect,
mishandling, misapplication, alteration, modification, faulty installation, set-
up adjustments, improper antenna, inadequate signal pickup, maladjustment
of consumer controls, improper operation, power line surge, improper
voltage supply, lightning damage, rental use of the product or service by
anyone other than an authorized repair facility or damage that is attributable
to acts of God.