Digital Watchdog PTZ39X User manual

Super Speed Dome
PTZ Outdoor Dome Camera
Version 1.00
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
User’s Manual
PTZ39X

2
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
This symbol indicates that dangerous voltage
consisting a risk of electricshock is present within
this unit.
This exclamation point symbol is intended to alert the
user to the presence of important operating and
maintenance (servicing)instructions in the literature
accompanying the appliance
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (BACK). THERE ARE NO
USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to
rain or moisture.
1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any
other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric
shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal
heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury.
6. Do not place conductive objects (e.g. screw drivers, coins, metal things, etc.) or containers filled
with water on top of the camera. Doing so may cause personal injury due to fire, electric shock,
or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued use in such
a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or
modify this product in any way.
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or
electric shock.
11. When ambient temperature is below the freezing point, the dome cover will frost and the power.
will fail. In this case, install or reboot the system, and the frost will disappear 3 hours after turning
on the power.
[Note that the lowest guaranteed operating temperature is -45°C/-49°F without wind.]
WARNING
WARNING

Safety Information
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject
to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C),
or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn o the power and then move
or reinstall it.
4. Remove the power plug from the outlet when there is a lightning. Neglecting to do so may cause
fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as the sun, for this may
damage the CCD image sensor.
8. The camera shall not be exposed to dripping or splashing, and no objects filled with liquids, such as
vases, shall be placed on the camera.
9. The main plug used to disconnect the device shall stay readily operable at any time.
CAUTION
3

WARNING
1. Read these instructions.
2. Keep these instructions.
3. Regard all warnings.
4. Follow all instructions.
5. Do not use this camera near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatuses that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for a replacement.
10. Protect the power cord from being walked on or pinched particularly at or near plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specied by the
manufacturer or sold with the camera.
13. Unplug this camera when a cart is used. Use caution when
moving the cart that contains the camera to avoid injuries that can result from the camera
falling over.
14. Refer all servicing to qualied service personnel. Servicing is required when the camera has
been damaged in any way, such as power supply cord or plug is damaged, liquid has spilled on
the the camera, objects have fallen into the camera, the camera has been exposed to rain
or moisture, the camera does not operate normally, or the camera has dropped.
Safety Instructions
4

5
Contents
6
7
8
Features
Product & Accessories
Parts Name
2
4
Safety Information
Safety Instructions
INTRODUCTION
9
11
14
DIP Switch Setup
Installation
Cabling
INSTALLATION
16
17
18
19
20
21
22
24
26
28
29
30
32
34
35
37
38
39
40
42
Check Points before Operation
Functions
OSD Display of Main Screen
General Rules of Key Operation for Menu
OSD - ROOT MENU & SYSTEM INFORMATION
OSD - DISPLAY SETUP > CAMERA ID
OSD - DISPLAY SETUP > PRIVACY ZONE
OSD - MOTION SETUP
OSD - FUNCTION SETUP > PRESET SETUP
OSD - FUNCTION SETUP > SCAN SETUP
OSD - FUNCTION SETUP > PATTERN SETUP
OSD - FUNCTION SETUP > GROUP SETUP
OSD - FUNCTION SETUP > SCHEDULE SETUP
OSD - CAMERA SETUP > WB SETUP
OSD - CAMERA SETUP > AE SETUP
OSD - CAMERA SETUP > SPECIAL
OSD - INTELLIGENCE > MASK AREA
OSD - INTELLIGENCE > ALARM OUT
OSD - SYSTEM SETUP
OSD - SYSTEM INITIALIZE
OSD MENU
43
44
Dimension
Specification PTZ39X
SPECIFICATIONS
x39

Features
6
CAMERA SPECIFICATIONS
• CCD Sensor: EX-View HADTM CCD
•
Zoom Magnification: ×39 Optical, ×12 Digital Zoom
• Wide Dynamic Range
• Day & Night Function: ICR (IR Cut filter Removal)
• Various Focus Mode: Auto Focus/Manual Focus/
Semi-Auto Focus
• Independent or Global Camera Settings for Each
Preset Location
POWERFUL PAN/TILT FUNCTIONS
• Maximum 360°/SEC High Speed Pan/Tilt Motion
• Vector Drive Technology: Pan/Tilt Motions are
accomplished in the shortest path. As a result,
time to target view is reduced dramatically and
the video on the monitor is very natural to watch.
• Ultra low speed (0.05°/SEC) enables operator to
locate camera to desired target view with accuracy
and ease.
• Zoom-Proportional Pan/Tilt speed helps operator
to move the camera easily.
PRESET, PATTERN, SCAN, GROUP, PRIVACY
ZONE, SCHEDULE, AND MORE...
• Maximum 127 presets are assignable. Each of
them have independent characteristics, such as
white balance, auto exposure, label, alarm
input/output, etc.
• Maximum 8 set of scans can be stored. This
enables user to move camera repetitively between
two preset positions with designated speed.
• Maximum 4 patterns can be recorded and played
back. This enables the camera to follow any
trajectory operated by the joystick as closely as
possible.
• Maximum 8 set of group actions can be stored.
This enables the camera to move repetitively
between different combination of preset, pattern,
or scan. A group is composed of maximum 20
entities of preset, pattern, or scan.
•
Maximum 8 privacy zones can be set up to protect
privacy of other people.
• 7 rules of schedule can be assigned by day and
time. Appropriate actions (such as home, preset,
scan, pattern, and group) can be defined for each
rule. Also, it is possible to use weekday and all days
to simplify the rule.
PTZ (PAN/TILT/ZOOM) CONTROL
• With RS485 communication, a maximum of 255
cameras can be controlled at the same time.
• Auto, Pelco-D, Pelco-P, Samsung, Panasonic, Kalatel,
AD(American Dynamics) protocol can be selected
as a control protocol in the current version of
firmware.
OSD(ON-SCREEN DISPLAY) MENU
• OSD Menu is provided to display the status of
camera and to configure the functions interactively.
•
Camera ID, Pan/Tilt/Zoom/Direction , Alarm Input/
Output, Date/Time, Current Temperature, and
Preset are displayed on screen.
• Each display item can be turned on or off
independently.
ALARM I/O FUNCTIONS
• 8 alarm sensor inputs and 4 relay output are
available.
• To reject external electric noise and shock perfectly,
alarm sensor input is decoupled with photo coupler.
• The signal range of sensor input is from DC 5.0 to
12.0 volts to adopt various applications.
• If an external sensor is activated, camera can be set
to move to the corresponding preset position.
•
Relay outputs can be assigned to work with a certain
preset.
RESERVED PRESETS FOR SPECIAL PURPOSE
• Most of camera settings are directly changed by
calling reserved presets, not entering into OSD
menu. For more information, refer to “Reserved
Presets”(page 18) of this manual.

Product & Accessories
7
Wall Mount
Pendant Mount
Housing Safety
Cable Hanger
Waterproof Tape
Hole Template
Hexagonal Wrench
User’s Manual
Anchor Bolt (4pcs)
Safety Wire
102.0
142.0
User’s Manual
Product Accessories

Part Name
8
Wall or Pendant Mount Bracket
The Wall or Pendant Mount Bracket is used to
install the camera onto the wall or ceiling. It
includes a built-in junction box.
Th junction box accommodates the inner box.
Sunshield & Upper Housing
PTZ Mechanism
Dome Safety Wire
Dome Cover
Inner Box
Housing Safety
Cable Hanger
Wall Mount Bracket
Pendant Mount Bracket
1
1
2
3
4
Inner Box
The inner box has many important roles. On top of the
box, there are dip switches and terminal locks for
power supply, video, audio, alarm input and alarm
output.
Sunshield & Upper Housing
The Sunshield protects the bubble dome cover from
sun rays and rainfall. The upper housing, which
is attached to the sunshield, accommodates the PTZ
mechanism. Also, the upper housing will be connected
to both the mounting brackets and the dome cover.
Dome Cover
Do not detach the protection vinyl from dome cover
until the installation process is completed. The vinyl
will protect the dome cover from scratches and dust.
The dome cover has a built-in fan and heater to
remove moisture from the bubble dome.
4
3
2

DIP Switch Setup
9
Before installing the camera,
you should first set the DIP Switch
to configure the Camera ID
(Communication Protocol).
Inner Box
1. Communication Protocol Setup
Congure the appropriate protocol using the
DIP switch combination.
- If you set the protocol as AUTO, camera will
automatically recognize the type of protocol
being used; however, this will not recognize
the AD protocol.)
- If you want to control the camera using the DVR
or a system
keyboard, the protocol must be.
identical to the camera protocol. Otherwise, you
w ill not be able to control the camera.
- If you change the camera protocol by adjusting
the DIP switch, the change will be eective after
you reboot the camera.
Protocol Setup Baud Rate Setup RS-485
Termination Resistor
ON
8J
21 3 4 5 6 7 8
ON
8J 21 3 4 5678
AUTO- Factory Default
1
ON
8J 21 3 4 5678
PELCO-D
2
ON
8J 21 3 4 5678
PELCO-P
3
ON
8J 21 3 4 5678
SAMSUNG
4
ON
8J 21 3 4 5678
PANASONIC
5
ON
8J 21 3 4 5678
GE(Kalatel)
6
ON
8J 21 3 4 5678
AD (American Dynamics)
7

DIP Switch Setup
10
2. Communication Baud Rate Setup
Select the appropriate Baud Rate using the
following DIP switch combination.
4. Camera ID Setup
The ID number of camera is set using binary
number.
The examples are shown below.
Inner Box
3. RS-485 Termination Resistor
- Pin 8 is used to turn ON / OFF the
the RS-485 termination.
Normally, it should be set as OFF.
- When you have trouble with long daisy chain
style connection, turn ON this termination
switch for the last camera.
ON
8J 21 3 4 5678
2400 BPS
1
ON
8J 21 3 4 5678
4800 BPS
2
ON
8J 21 3 4 5678
9600 BPS - Factory Default
3
ON
8J 21 3 4 5678
19200 BPS
4
38400 BPS
5
ON
8J 21 3 4 5678
ON
8J 21 345678
Pin 1 2 3 4 5 6 7 8
1 2 4 8 16 32 64 128ID Value
ex) ID=5
ex) ID=10
ON
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
- If you want to control a certain camera, you must
match the Camera ID with the CAM ID setting
of your DVR or keyboard controller.
- The range of Camera ID is 0~255. Factory default
of Camera ID is 1.

Installation
5
6
You have to detach the PTZ mechanism from the
upper housing to plug the cable connector.
To detach PTZ mechanism, press down and hold
against both sides of the black handles on the
PTZ mechanism.
[2]
[1]
[3]
[1] Wind the waterproof tape around the pipe of
the upper housing.
[2] Hook the safety wire to the hole of the safety
cable hanger.
[3] Attach the upper housing to wall mount
bracket by turning it at least seven times.
To secure the upper body orientation, turn
the handle of double nuts clockwise until it is
tight.
11

Installation
7
8
9
10
Plug the cable connector from the junction box
properly. Align the one touch connectors in the upper
housing with that of the PTZ mechanism
and force into place.
To lock the PTZ mechanism to the upper housing,
press the two black handles and push the PTZ
mechanisim into the upper housing until it
sounds snap.
Plug the main cable into the main connector
that is located on the upper housing and press
the main cable until it sounds snap to lock.
Plug safety wire into the connectors located
on the upper housing.
12

Installation
13
11 Close the dome cover carefully. Match the
“Arrow Mark” to nd the right location.
Tighten the four screws on the dome cover in
the same sequence shown in the picture.
To maintain the best sealing, the torque of each
screw must be in the range between
0.5 ~ 1.0 N·m (0.3 ~ 0.73 lbf·ft).
Arrow Mark
Arrow Mark
12

Cabling
14
RS-485
(Keyboard Controller/DVR)
Video
Power
Video Connection
Connect with BNC coaxial cable.
RS-485 Communication (DVR/Keyboard)
For PTZ control, connect this line to keyboard and
DVR. To control multiple cameras at the same time,
the RS-485 communication lines are connected in
parallel as shown below.
1Power Connection
Please check the voltage and the current capacity of
rated power carefully.
2
3
BNC Video
Inner Box
1
2
3
Rate Power Current
Consumption
Input
Voltage Range
AC 24V 2.5AAC 19V ~ 29V
Keyboard Controller/DVR
RS-485
#1 #2 #n
~
~
~
RS-485

15
Cabling
N.C
Activation
Activation
N.O In 2
COM
In 2
COM
In 2
COM
In 2
COM
Alarm Output
Alarm Input
Inner Box
Alarm Input/Sensor
5
It is noted that short circuit between GND and Input Pin
means alarm activation.
Sensor Input
To use alarm input, select the type of sensor to
you wish to use. The sensor types are “Normal
Open” and “Normal Close.” If sensor type
is not selected properly, the alarm can be activated
reversely.
4
Alarm Output
The 4 alarm outputs are the relay contact type.
Therefore, you do not have to worry about the
polarity, AC/DC, and isolations between
channels. However, regard the power capacity
of relay contact written above.
5
COM
In 1
COM
In 1
In 8
Alarm Output
4
ALARM INPUT
GND1 234 5678
OUT1 OUT2 OUT3 OUT4
OUT1 OUT2 OUT3 OUT4
Out Out
ALARM INPUT
GND1 234 5678

Check Points Before Operation
16
1. Before power is applied, please check the cables carefully.
2. The camera ID of the controller must be identical to that of the camera you wish to control. You can check the
camera ID in the system information of the OSD menu.
3. If your controller supports multi-protocols, the protocol must be changed to match that of the camera.
4.
If you changed camera protocol by changing DIP switch, the change will be eective after you reboot the camera.
5. Since the operation method can be dierent for each controller available, refer to the manual for your controller
if camera can not be controlled properly.
Auto Calibration
If the camera is continuously subject to very high
temperatures (over 50°C or 122°F) for a long period,
the camera can lose focus and produce blurry
images. In this case, it is recommended to turn on
AUTO CALIBRATION by running preset 165.
If you execute AUTO CALIBRATION, the camera will
calibrate its focus for 10 seconds every 24 hours.
To turn OFF this function, please, run preset 166.
Open OSD Menu
Using the OSD menu, preset, pattern, scan, group, and
alarm input function can all be configured for your
application. Run preset 95 to open your OSD menu
and begin configuring your camera.
Preset and Pattern Function Pre-check
Check how to operate preset, pattern, scan, and group
functions with keyboard controller or DVR in advance
to operate the PTZ camera with it.
(Refer to your keyboard or DVR manual.)
If keyboard controller/DVR has no pattern key or
function, use shortcut keys with preset numbers.
For more information, refer to “Reserved Preset”
below.
Reserved Preset
Some preset numbers are reserved for special functions.
Preset key + 95: Opens OSD menu
Preset key + 131~134: Runs pattern function 1 ~ 4
Preset key + 141~148: Runs scan function 1 ~ 8
Preset key + 151~158: Runs group function 1 ~ 8
Preset key + 161~164: Sets relay 1~ 4 output to OFF
Set key + 161~164: Sets relay 1~ 4 output to ON
Preset key + 165: Sets auto calibration to ON
Preset key + 166: Sets auto calibration to OFF
Preset key + 167: Zoom proportional jog ON
Set key + 167: Zoom proportional jog OFF
Preset key + 170: Sets camera BLC mode to OFF
Preset key + 171: Sets camera BLC mode to HIGH
Preset key + 174: Sets camera focus mode to AUTO
Preset key + 175: Sets camera focus mode to MANUAL
Preset key + 176: Sets camera focus mode to SEMI-AUTO
Preset key + 177: Sets day & night mode to AUTO
Preset key + 178: Sets day & night mode to NIGHT
Preset key + 179: Sets day & night mode to DAY
Preset key + 190: Sets OSD display mode to AUTO
(except privacy mask)
Preset key + 191: Sets OSD display mode to OFF
(except privacy mask)
Preset key + 192: Sets OSD display mode to ON
(except privacy mask)
Preset key + 193: Sets all privacy mask display to OFF
Preset key + 194: Sets all privacy mask display to ON
Preset key + 200: Sets digital zoom to ON
Preset key + 201: Sets digital zoom to OFF
1 3
4
2

17
Functions
1. Set Preset
Method 1) Use keyboard controller:
Refer to your system keyboard manual.
Method 2) Use OSD menu.
2. Run Preset
Method 1) Use keyboard controller:
Preset key + Number key (1~128)
3. Delete Preset
To delete preset, use OSD menu.
Preset
Maximum 127 positions can be stored as preset
positions. The numbers 1 to 128 can be assigned as
preset numbers, but 95 is reserved for starting the
OSD menu.
See section ROOT MENU > FUNCTION SETUP >
PRESET SETUP.
1
Scan
The scan function allows camera to move repeatedly
between 2 preset positions.
See section ROOT MENU > FUNCTION SETUP >
SCAN SETUP.
2
1. Set Scan
To set scan, use OSD menu.
2. Run Scan
Method 1) Scan key + Scan no. (1~8) + Enter key
Ex. Run scan 2 = Scan key + [2] + Enter key
Method 2) Preset key + [Scan no. (1~8) + 140]
Ex. Run scan 2 = Preset key + [142]
3. Delete Scan
To delete scan, use OSD menu.
Pattern
Pattern function allows the camera to memorize a
path created by a joystick controller and then
revive the path exactly as it memorized for an
assigned time.
See section ROOT MENU > FUNCTION SETUP >
PATTERN SETUP.
3
1. Set Pattern
To set pattern, use OSD menu.
2. Run Pattern
Method 1) Pattern key + Pattern no. (1~4) + Enter key
Ex. Run pattern 2 = Pattern key + [2] + Enter key
Method 2) Preset key + [Pattern no. (1~4) + 130]
Ex. Run pattern 2 = Preset key + [132]
3. Delete Pattern
To delete pattern, use OSD menu.
Group
The group function allows you to run a sequence of
presets,
pattern, and/or scans.
See section ROOT MENU > FUNCTION SETUP >
GROUP SETUP.
4
Schedule
The schedule function allows you to run an appropriate
function like preset, scan, group, pattern, home, or
move at a designated day and time.
See section ROOT MENU > FUNCTION SETUP >
SCHEDULE
SETUP.
5
When the pattern is saved or executed, the pan/tilt is
operated with AUTO FLIP-OFF.
1. Set Group
To set group, use OSD menu.
2. Run Group
Method 1) Group key + Group no. (1~8) + Enter key
Ex. Run group 2 = Group key + [2] + Enter key
Method 2) Preset key + [Group no. (1~8) + 150]
Ex. Run group 2 = Preset key + [152]
3. Delete Group
To delete group, use OSD menu.

OSD Display of Main Screen
PATTERN 1 PRESET LABEL
CAMERA ID_TOP
CAMERA ID_TOP
CAMERA ID_BOT
CAMERA ID_BOT
23/MAR/2009
24 00 00
CAM 1
O 1234
I12345678
359/180/x100/SE
F
Preset Label
- The label stored for a specific preset.
- See section ROOT MENU > FUNCTION SETUP >
PRESET SETUP > LABEL.
Camera ID_Top
- If CAMERA ID is set to TOP, Camera ID will display
in this area.
- See section ROOT MENU > DISPLAY SETUP >
CAMERA ID.
Camera ID_Bottom
- If CAMERA ID is set to BOT, Camera ID will display
in this area.
- See section ROOT MENU > DISPLAY SETUP >
CAMERA ID.
Date / Time
- Shows the current date and time.
- See section ROOT MENU > SYSTEM SETUP >
DATE/TIME SETUP.
Image Flip
- Indicates the images that has been reversed
by the auto flip function.
- See section ROOT MENU > CAMERA SETUP >
IMAGE FLIP.
Address
- Shows the current RS-485 address information.
-
See section ROOT MENU > SYSTEM INFORMATION.
Action Title
The following are examples of action titles with
their descriptions.
Action Title Description
SET PRESET 123
PRESET 123
PATTERN 9
SCN 1/PRESET 123
RANGE OVER
Store preset 123.
It reached preset 123.
The camera is running pattern 9.
The camera is running scan 1.
The action received is not within the
range supported.
UNDEFINED The action received is not defined.
Alarm I/O Information
- This information shows the current status of alarm
input and output.
- “I” means input, and “O” means output.
- If the alarm input is ON, it will show the number of
the input. If an input is OFF, “-” will be displayed.
“O:1 - - -” means output 1 is ON and other outputs
are OFF.
- Ex. When input 2 is ON and output 1 is ON, OSD will
display as below.
Compass Direction
- Shows the current compass direction of the camera.
- The direction is shown as N(North), S(South), E(East),
W(West), NE(Northeast), NW(Northwest),
SE(Southeast), SW(Southwest).
- See section ROOT MENU > SYSTEM SETUP >
SET NORTH DIRECTION.
Zoom Magnification
Shows the current zoom magnification.
Tilt / Pan Angle in Degree
Shows the current tilt (0 ~ 180) and pan(0 ~ 359) angle.
1
2
3
4
5
6
7
8
9
11
10
12
23/MAR/2009
24 00 00
CAM 1
O 1---
I-2------
359/180/x100/SE
Date / Time
Action Title
Preset Label
Camera ID_Top
Camera ID_Bottom
1
2
3
Compass Direction
Zoom Magnification
Tilt Angle in Degree
Pan Angle in Degree
Alarm I/O Information
5
6
Image Flip
Address
4
8
9
10
11
12
7
18

General Rules of Key Operation for Menu
19
The characters < > that surround the menu item
indicate that there is a sub menu.
Move among the different selections in the menu
list using the joystick in the Up/Down or Left/Right
direction.
To enter a sub-menu, press Near or Enter key.
To go back a menu, press Far key.
To change a value of an item, move the joystick in
the Up/Down direction.
Press Near or Enter key to save values and press Far
key to cancel values.
1
2
3
5
6
4
6
Press
Near/Enter
or
Far Key
>
DISPLAY SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
CAMERA ID
PTZ INFORMATION
ACTION TITLE
PRESET LABEL
ALARM I/O
DATE/TIME
<PRIVACY ZONE>
BACK
EXIT
ON
AUTO
AUTO
AUTO
AUTO
ON
DISPLAY SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
CAMERA ID
PTZ INFORMATION
ACTION TITLE
PRESET LABEL
ALARM I/O
DATE/TIME
<PRIVACY ZONE>
BACK
EXIT
ON
AUTO
AUTO
AUTO
AUTO
ON
DISPLAY SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
CAMERA ID
PTZ INFORMATION
ACTION TITLE
PRESET LABEL
ALARM I/O
DATE/TIME
<PRIVACY ZONE>
BACK
EXIT
OFF
AUTO
AUTO
AUTO
AUTO
ON
ROOT MENU
- - - - - - - - - - - - - - - - - - - - - - - - - - -
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<MOTION SETUP>
<FUNCTION SETUP>
<CAMERA SETUP>
<SYSTEM SETUP>
<SYSTEM INITIALIZE>
EXIT
ROOT MENU
- - - - - - - - - - - - - - - - - - - - - - - - - - -
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<MOTION SETUP>
<FUNCTION SETUP>
<CAMERA SETUP>
<SYSTEM SETUP>
<SYSTEM INITIALIZE>
EXIT
Joystick
Down
Joystick
Down
Joystick
Up
Joystick
Up
>
>
Press
Near/Enter
Key
Press
Far Key
>
>
Press
Near/Enter
Key
Press Far Key
>
>
>
>
5
1
3
4
2

OSD -
ROOT MENU & SYSTEM INFORMATION
20
ROOT MENU
- - - - - - - - - - - - - - - - - - - - - - - - - - -
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<MOTION SETUP>
<FUNCTION SETUP>
<CAMERA SETUP>
<INTELLIGENCE>
<SYSTEM SETUP>
<SYSTEM INITIALIZE>
EXIT
FIRMWARE VER
Shows the current firmware version.
COLOR SYSTEM
Shows the current analog video system.
PROTOCOL
Shows the current PTZ control protocol.
BAUD RATE
Shows the current baud rate of the PTZ control.
ADDRESS
Shows the current camera ID of the PTZ control.
<SYSTEM INFORAMTION>
Shows system information and current system configuration.
<DISPLAY SETUP>
Enable/Disable OSD display on main screen.
<MOTION SETUP>
Configures motion related settings.
<FUNCTION SETUP>
Configures various functions such as preset, scan, pattern, group,
and schedule.
<CAMERA SETUP>
Configures camera related functions and data.
<INTELLIGENCE>
Configures camera to detect an object moving or changing.
<SYSTEM SETUP>
Configures the basic system setup.
<SYSTEM INITIALIZE>
Initializes system configuration and sets all data to factory default
configuration.
EXIT
Exits the OSD setting.
SYSTEM INFORMATION
- - - - - - - - - - - - - - - - - - - - - - - - - - -
FIRMWARE VER
COLOR SYSTEM
PROTOCOL
BAUD RATE
ADDRESS
BACK
EXIT
1
.0
NTSC
AUTO
9600
1
1
1
ROOT MENU
1
SYSTEM INFORMATION
1