Digital Watchdog DWC-B562DIR User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
DWC-B562DIR
960H Outdoor Bullet Camera
User Manual
11192012
Value

22
PRECAUTIONS
FCC COMPLIANCE
WARNING: Changes or modifications are not expressly approved by the manufacturer.
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits,
or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to
high levels.
Cleaning: To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface: The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. This equipment generates, uses,
and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications.

3
Table of Contents
Introduction
Installation
Camera OSD Menu and Glossary
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Included Accessories
Easy Installation
Connecting to Monitors
OSD Control Board
Camera Setting Angle
4
5
6
7
8
9
10
11
13-24
25
26-27
28-29
Adjusting the Lens 12
10

4
10
FEATURES*
DWC-B562DIR
1/3” 960H High Resolution CCD
700 TV Lines
3.3~12mm Varifocal Auto Iris Lens
85ft Range IR with Intelligent Camera Sync, Smart IR
Electronic Day and Night
HME (Highlight Masking Exposure)
AGC / Smart BLC / AWB
Night-Up
Mirror Image Control
Programmable Privacy Zones (8) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Secondary Video-BNC Output
IP66 Certified, No Fog or Condensation

5
PARTS & DESCRIPTIONS*
P
1
4
2
3
6
9
8
5
7
1Front Cover
4Bracket
5Set Screw
2Lens
3Body Case
6BNC
Sunshield Screw
8
Sunshield
9
7Power Connector

6
DIMENSIONS IN MILLIMETERS (INCHES)*
Ø68
(Ø2.67”)
41.4
(1.63)
146.7(5.77”)
251.2(9.89”)
111.5(4.39”) 115.8(4.56”)
80.6(3.17”)

7
INSTALLATION*
Included with Value Line Bullet Camera
1. User Manual
2. Mounting Template
1 2
3
4
3. Second Video Jack
4. Mounting Screws (3)
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
DWC-B562DIR
Outdoor Bullet Camera
User Manual
05032012

8
EASY INSTALLATION*
1. Using the template, mark appropriate holes
on the mounting surface.
2. Secure the camera by drilling the three screws through
the camera holes into the mounting surface.
3. Adjust the camera’s lens. See pages 10-12 for
more information.

9
CONNECTING TO MONITORS*
CAUTION
Check for polarity when using a DC 12V power supply.
All cameras are equipped with a service monitor output on the camera module for easy on-site
configuration.
300.0(11.8”)

10
OSD CONTROL BOARD**
Joystick
Connector 1
FUNCTION
S OF CONTROL B
OARD
Joystick: Functional control of OSD (On Screen Display) Menu
Connector 1: Second Video Output Connector
①
②
1
2
NOTE: Turn the front cover counter-clockwise and remove to access the OSD Contol Board.

11
CAMERA SETTING ANGLE*
1
2
To adjust the camera angle, loosen the
screw located on the bracket.
Adjust the camera angle and lock the bracket
screw back in place.

12
A
DJUSTING THE LENS *
ZOOMFOCUS
1
2
3
4
Loosen the zoom and focus handles by rotating them counter-clockwise.
Zoom: Adjust the field of view by moving the handle to the RIGHT (tele) to zoom in, or to the
LEFT (wide) to zoom out.
Adjust the focus the same way as described above AFTER the desired zoom position
is established.
Once the desired adjustments have been made, please tighten the handles back by
turning them clockwise.
To acess the zoom and focus handles, turn the front cover counter-clockwise and remove.
5

13
MODULE OSD MENU*
EXPOSURE COLOR DAY NIGHT
FUNCTION MOTION PRIVACY
SET-UP EXIT
LENS
MANUAL, DC
BACKLIGHT
OFF / BLC / HME / D-WDR
AGC
OFF / LOW / MID / HIGH / HIGHEST
2D-DNR
OFF / LOW / MIDDLE / HIGH
EXIT JUMP
SAVE & EXIT / EXIT
WB MODE
AWC / ATW / MANUAL / PUSH
RED GAIN
0~255
BLUE GAIN
0~255
COLOR MODE
NORMAL / COOL / WARM
EXIT JUMP
SAVE & EXIT / EXIT
DAY & NIGHT
AUTO / COLOR / B&W
NIGHT C.
0~100
NIGHT A.
0~100
EXIT JUMP
SAVE & EXIT / EXIT
MIRROR
MIRROR / OFF
SHARPNESS
0~30
GAMMA
MANUAL / 0.45 / 0.60 / 1.0
SLC
OFF / ON
NIGHT-UP
OFF / ON
EXIT JUMP
SAVE & EXIT / EXIT
AREA SET
AREAS 1~4 OFF / ON
SENSITIV.
1~30
SHOW INDI.
OFF / ICON / TRACE
EXTER-OUT.
OFF / ON
EXIT JUMP
SAVE & EXIT / EXIT
MASK1
OFF / ON
MASK2
OFF / ON
MASK3
OFF / ON
MASK4
OFF / ON
MASK5
OFF / ON
MASK6
OFF / ON
MASK7
OFF / ON
MASK8
OFF / ON
EXIT JUMP
SAVE & EXIT / EXIT
TITLE
OFF / ON
DPC SET
OFF / AUTO
MONITOR
MODE1 / MODE2
LANGUAGE
ENGLISH /
DEUTSCH / FRENCH /
ITALIAN / RUSSIAN / SPANISH / DOUTCH
SD COLOR
BLUE / GREEN / CYAN / RED /
MAGENTA / YELLOW / PURPLE / GRAY
COMMUNICA.
OFF / ON
FACTORY SET.
NO / YES
EXIT JUMP
SAVE & EXIT / EXIT
SAVE & EXIT
EXIT

14
EXPOSURE
LENS
MANUAL
DC DC mode supports the auto-iris varifocal lens.
MANUAL mode supports the fixed board lens or
the manual iris lens.
Note:
Both MANUAL and DC mode have FOCUS TARGET..
You can adjust the focus by finding the highest number on the
FOCUS TARGET.
ELC and DC levels are adjustable. The higher the number, the brighter the image.
E. Shutter sets the shutter speed levels from 1/60 to 1/100000.
AUTO and DC-AUTO are the default shutter speeds for both indoor and outdoor use.
Select 1/100FLC to run camera in flickerless mode.

15
HME HIGHLIGHT MASKING EXPOSURE
HME masks highlights to allow objects to appear clearly on the
screen. If ON is selected, HME level is adjustable. The lower
the number, the darker the masking areas.
DIGITAL WIDE DYNAMIC RANGE
D-WDR is one of the backlight compensation functions.
You can adjust the D-WDR level from 0-20. The lower
the number, the brighter the backlight.
D-WDR
BLC BACKLIGHT COMPENSATION
Select MANUAL or SMART. SMART is recommended.
BACKLIGHT
OFF
If MANUAL is selected, you can adjust the BLC levels in
four areas of the scene (Top, Bottom, Left,
Right). Increase the BLC levels where you want
to make the image brighter.
If SMART is selected, the camera will automatically adjust the
BLC zone. Choose from LOWEST, LOW, MID, HIGH.
EXPOSURE

16
AGC (Auto Gain Control)
OFF/ LOW / MID / HIGH / HIGHEST AGC enhances picture brightness in low light conditions.
A higher level AGC setting makes the image brighter;
however, it could cause an increase in noise.
2D-DNR (Digital Noise Reduction)
OFF/ LOW / MIDDLE / HIGH 2D-DNR reduces the noise on the screen in low light conditions.
It allows for clearer images even at night.
EXIT_JUMP
SAVE & EXIT
EXIT
Exit the OSD after saving the current settings.
Exit the OSD without saving.
EXPOSURE

17
COLOR
WB MODE
AWC Auto White Balance Control mode
compensates for color temperature changes
between 2000K and 18000K.
ATW Auto Tracking White Balance Control mode
compensates for color temperature changes
between 2500K and 9500K.
MANUAL Users can control the white balance manually
by changing RED GAIN and BLUE GAIN
(see below).
PUSH LOCK Push Lock fixes the white balance based
on current lighting.
RED GAIN
0~255 Adjusts the amount of red in the image.
BLUE GAIN
0~255 Adjusts the amount of blue in the image.
COLOR MODE
NORMAL
COOL
WARM
Color is similar to actual color.
Color has more blue.
Color has more red.
EXIT_JUMP
SAVE & EXIT
EXIT
Exit the OSD after saving the current settings.
Exit the OSD without saving.

18
DAY NIGHT
D&N MODE
AUTO Camera switches between day and night automatically depending
on light level. Camera will stay in color mode when there is
enough light. Camera will switch to B&W at night or other low light
environments.
COLOR Camera always stays in day/color mode.
B&W Camera always stays in night mode.
If AUTO is selected, please define the following settings:
▪ BURST: ON/OFF. If ON is selected, the camera provides a color burst signal in
▪night mode. If OFF, no color burst signal is provided.
▪ COLOR → B&W: Adjusts the light level at which the camera switches from day
▪(color) to night (B&W) mode. The higher the number, the lower the light level.
▪ B&W → COLOR: Adjusts the light level at which the camera switches from
▪night (B&W) to day (color) mode. This number should be lower than the value
▪ of COLOR → B&W above.
▪ SMART IR: ON/OFF. If using IR LEDs, ON is recommended.
▪ READ TIME: Time interval delay before switching from day mode to night mode.
▪It is adjustable from 3 seconds to 12 seconds.
▪ EX_IR INT. AUTO/EXT.: If using IR LEDs built into the camera, select AUTO.
▪If using external IR LEDs separately, select EXT.
NIGHT C.
0~100 Color will be reduced in low light conditions.
(This level cannot be adjusted when 2D-DNR is ON.)
NIGHT A.
0~100 Edge sharpness will be reduced in low light conditions.
(This level cannot be adjusted when 2D-DNR is ON.)
EXIT_JUMP
SAVE & EXIT Exit the OSD after saving the current settings.
EXIT Exit the OSD without saving.

19
FUNCTION
MIRROR
OFF
MIRROR
SHARPNESS
0~30
GAMMA
0.45/ 0.6/ 1.0/
MANUAL
SLC (Side Light Compensation)
OFF/ ON
OFF/ ON
EXIT_JUMP
NIGHT-UP
SAVE & EXIT
EXIT
Exit the OSD after saving the current settings.
Exit the OSD without saving.
Flips the image horizontally.
Sets the image sharpness. The higher the number,
the sharper the image.
Controls the output signal level. The higher the
setting, the darker the dark colors will be.
0.45 is default.
Adjusts sensitivity in low light conditions by set-up level. If ON is selected,
the set-up level becomes higher and the images become brighter.
Increases brightness on sides of the image.

20
MOTION The camera can detect movement and display an
alarm on the screen when movement is detected.
AREA SET
AREA 1,2,3,4 OFF/ON
If ON, motion areas can be selected and moved
accordingly. Select Areas 1-4 and adjust using
controls for TOP, BOTTOM, LEFT, or RIGHT.
SENSITIV.
1~30
Sensitivity level of the motion detection is adjustable.
Motion detection will be more sensitive at a higher number.
SHOW INDI.
OFF/ ICON /
TRACE
Set the Show Indicator to OFF, ICON, or TRACE.
If ICON is selected, a bell will appear in the upper right
hand corner when motion is detected. If TRACE is
selected, the area where motion was detected will be
highlighted.
EXTER OUT
OFF/ ON
ALARM SIGNAL EXTERNAL OUTPUT
If ON is selected, you can set how long the alarm is
displayed on the screen when motion is
detected (0~15 seconds).
EXIT_JUMP
SAVE & EXIT
EXIT
Exit the OSD after saving the current settings.
Exit the OSD without saving.