Digital Watchdog DWC-D362D User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Indoor Dome Camera
DWC-D362D
DWC-D362DIR
User Manual
02222012

22
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacturer.
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning :
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface :
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to Provide reasonable protection against harmful
interference. when the equipment is operated in a residential environment. This equipment generates, uses,
and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications.

3
Table of Contents
Introduction
Installation
Camera OSD Menu and Glossary
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Included Accessories
Easy Installations
Base Installations
Connecting to Monitors
Adjusting the Camera
4-5
6
7
8
9
10
11
12
14-17
18
19-20
21
Adjusting the 3-Axis Gimbal 13

4
FEATURES*
DWC-D362D
Sharp 1/3” CCD
540 TV Lines
2.8 ~ 11mm Varifocal Auto Iris Lens
Electronic Day and Night
DRC (Dynamic Range Compressor)
HME (Highlight Masking Exposure)
SLC (Side Light Compensation)
AGC / BLC / AWB
Mirror Image Control
RS485 Built-In (Optional)
Programmable Privacy Zone (4) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
Video Test Output Included

5
FEATURES*
DWC-D362DIR
Sharp 1/3” CCD
540 TV Lines
2.8 ~ 11mm Varifocal Auto Iris Lens
85ft Range IR with Intelligent Camera Sync
Electronic Day and Night
DRC (Dynamic Range Compressor)
HME (Highlight Masking Exposure)
SLC (Side Light Compensation)
AGC / BLC / AWB
Mirror Image Control
RS485 Built-In (Optional)
Programmable Privacy Zone (4) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
Video Test Output Included

6
PART & DESCRIPTIONS*
1Lens
4Upper case
5Bubble
2Power Input Connctor
12VDC/24VAC Dual Voltage
3Video Output Connector - BNC
6Control board
7Power board
Mounting screw
9
8Bottom case
2
6
7
1
8
3
9
4
5
No IR
IR

7
DIMENSIONS IN MILLIMETERS*
10.1
(0.4”)
39.4
(1.6”)
82.3
(3.24”)
Ø118.0
(Ø 4.65”)
Ø118.0
(Ø 4.65”)
Ø89.0
(Ø 3.5”)
Ø20.0
(Ø 0.79”)
Ø14.5
(Ø 0.57”)
3- Ø4.5
(3- Ø0.18”)

8
INSTALLATION*
Included with Value Line Indoor Dome Camera
1. User Manual
2. Mounting Template
1 2
3 4
Ø15.0
Ø20.0
Ø118.0
Ø5.0
Mounting template
PD79
3. Second Video Jack
4. Mounting Screw (3)

9
EASY INSTALLATION*
Remove the Dome Cover
Before you can mount or adjust your PD79,
you must remove the dome cover. Insert a
coin or screwdriver in the slot on the dome
cover, then twist to pry the dome cover
from the camera base.
Install the Enclosure Cover
Dome Cover
Camera Base
To install the dome cover, align the dome cover
with the camera base and push until
it securely snaps into place.

10
BASE INSTALLATION*
1.Pull wires through and make connections,
Refer to page 11. Use mounting template to
mount camera with dry wall mounts and wood
screws.
2. Adjust the camera’s pan,tilt and zoom.
See page 13 for details.
3. Use the joystick to adjust the OSD menu.
See page 14~17 for details. 4. Attach the camera housing to the junction box using the assembly scrws.