Digital Watchdog MegaPix Pano DWC-PZ21M69T User manual

Quick Start Guide
DWC-PZ21M69T
WHAT’S IN THE BOX
Quick Manual &
Download Guide 1 Set Screw & Plastic Anchor – 4pcs 1 Set
Template Sheet 1 Set Tor x Wrench 1 Set
Moisture absorber -
2pcs & Absorber Guide 1 Set Waterproof cap & Gasket 1 Set
PoE Injector and
power cable 1 Set
Username: admin Password: admin
Attention: This document is intended to serve as a quick reference page for initial set-up.
It is recommended that the user read the entire instruction manual for complete and proper camera usage.
Tel: [phone]
Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Quick Start Guide
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 3 – INSTALLING THE CAMERA
STEP 2 – POWERING THE CAMERA
1. Mounting surface must withstand three times the weight of the camera.
2. Do not let the cables get caught in improper places or the electric line cover to be damaged. This may cause a short or fire.
3. Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.
4. For the installation process, remove the dome cover by loosening the screws on the dome. Use the wrench provided with the camera.
2. Your camera comes with a moisture absorber included in the package. This
absorber needs to be installed inside the camera, next to the lens, to prevent
moisture build-up on the camera’s dome that reduces image quality.
(1).Remove the moisture absorber from the packaging.
(2).Follow the diagram to place the absorber in the appropriate location.
3. The camera’s four individual sensors can be rotated and tilted to adjust the camera’s views. Max tilt and rotation:
- Rotation: 20º
- Tilt: 18º
4 . Assemble the dome cover over the camera body and detach the protecting film to complete the installation.
Connect the camera to the PoE injector included in the box. Connect the PoE injector to an adequate power source. See table
below for power source requirements. Refer to the user manual for more options to power up the camera.
Power Requirements Power Consumption
DC12V, PoE IEEE 802.3at PoE+ class 4
(High power PoE injector included)
DC12V Max 21.5W
PoE Max 23.4W
To reset the camera, press the reset button. Pressing the button for five (5) seconds will initiate a
camera-wide reset of all the settings, including network settings.
1. To use the camera’s water proof wiring:
(1).Install the LAN cable into (a).
(2).(b) will be assembled to (a) with a 1/4 turn.
(3).Thread (c) tightly to (b). a
b
c
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide Waterproof cap & Gasket
Quick Manual &
Download Guide
Screw &
Plasc Anchor-4pcs
Template Sheet
Torx Wrench
Moisture absorber - 2pcs
& Absorber Guide Waterproof cap & Gasket
NOTE: When using the PoE+ injector, do not connect the PoE injector to the
PoE/PoE+ switch or PoE/PoE+ enabled port of PoE/PoE+ switch.
NOTE: When using the waterproof cap, crimp the RJ45 connector after
passing the cable through the waterproof cap.
Template Sheet
Reset Buon
3
2
7
6
5
4
3
2
2
1
Template Sheet
Reset Buon
Ethernet
cable
PoE
Injector
Ethernet Switch
power cable,
connected to
adequate
power source.
Please attach 2 card type
absorbers to attachment
points as the picture.

Rev Date: 11/18 Copyright © Digital Watchdog. All rights reserved. Specifications and pricing are subject to change without notice.
STEP 4 – DW IP FINDER™
Quick Start Guide
Use the DW IP Finder™ software to scan the network and detect all MEGApix®cameras, set the camera’s
network settings or access the camera’s web client.
Network Setup
1. To install the DW IP Finder™, go to: http://www.digital-watchdog.com
2. Enter “DW IP Finder” on the search box at the top of the page and press Enter.
3. Click on the DW IP Finder from the search result and go to Software tab. Click on download icon
to download the DW IP Finder installation le.
4. Run the installation le and follow the wizard to install the DW IP Finder™. Open the
DW IP Finder™ and click ‘Scan Devices’. It will scan the selected network for all supported devices
and list the results in the table. During the scan, the DW logo will turn gray.
5. Select a camera from the list by double-clicking on the
camera’s image or clicking on the ‘Click’ button under the
IP Conf. column. The pop-up window will show the camera’s
current network settings, allowing admin users to adjust the
settings as needed.
6. To access the camera’s webpage, click on ‘View Camera
Website’.
7. To save the changes made to the camera’s setting, input
Username and Password of the camera and click Apply. Click
Scan Devices from the main screen again to display the
updated information.
Default ID / PW : admin / admin
‘Port Forwarding’ has to be set in your network’s router
for external access to the camera.
NOTE: For security purposes, it is highly recommended to
change your password after initial setup.
NOTE: Please see the full manual for additional installation options, connecting external devices, web viewer setup,
camera settings and more.
Thumbnail view
Firmware version
Camera’s uptime
Open Device
conguration
settings
Filter device type to scan
Scan devices
Select network to scan
Show/hide thumbnail view
Refresh thumbnail view
Bulk IP assignment
Firmware upgrade
Device’s
information
Default TCP/IP information: DHCP
Select DHCP if the internet service is dynamic IP. This will allow the camera to receive its IP address from
the DHCP server.
Select Static to manually enter the camera’s IP address, (Sub)Netmask, Gateway and DNS information.
* The camera’s IP must be set to Static if connecting to DW Spectrum
Contact your network administrator for more information.
1 2
4. Enter the camera’s username and password (default are admin / admin).
5. If you are accessing the camera for the rst time, install the VLC les to view video from the camera.
6. To adjust the camera’s sensors alignment, go to the camera’s settings, under Alignment conguration.
See the camera’s user manual for all setup options and congurations.
STEP 5 – WEB VIEWER
Once the camera’s network settings have been setup properly, you can access the camera’s web viewer.
To open the camera’s web viewer:
1. Find the camera using the DW IP
Finder.
2. Double-click on the camera’s view in
the results table.
3. Press the ‘View Camera Website.’
The camera’s web viewer will open
up in your default web browser.
Make sure you are using Internet
Explorer to view video from the
camera.