Digital Watchdog Star-Light Plus DWC-VA583WTIR User manual

Quick Start Guide Quick Start Guide
1. The mounting surface must withstand five times the
camera weight.
2. Do not let the cables get caught in improper places or the electric
line cover can be damaged. This may cause a short or fire.
3. Use the mounting template to mark and drill the necessary holes in
the mounting surface.
STEP 1 – PREPARING TO MOUNT THE CAMERA
Pass the wires through the mount bracket and make all
necessary connections. Connect the BNC cable and power
cables to the camera.
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
Power
Requirements Power Consumption
DC12V / AC24V
dual-voltage
DC12V (LED o): 4.36W, 363mA
DC12V (LED on): 7.6W, 638mA
AC24V (LED o): 4.5W, 278mA
AC24V (LED on): 6.27W, 456mA
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
DWC-VA583WTIR
Attention: This document is intended to serve as a quick reference for
initial set-up. It is recommended that the user read the entire instruction
manual for complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in
the ‘Search by Product’ search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
WHAT’S IN THE BOX
DC plug 1 Set Template
sheet 1 Set
Torque
wrench 1 Set Quick Setup Guide 1 Set
Screw and
plastic
anchor-2pcs
1 Set
Manual
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut
Screw &
Plasc Anchor-2pcs
Torx Wrench
Test Video Cable
Manual
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut
Screw &
Plasc Anchor-2pcs
Torx Wrench
Test Video Cable
Manual
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut
Screw &
Plasc Anchor-2pcs
Torx Wrench
Test Video Cable
Template sheet

1. Once all cables have been connected, use the screws included with the camera to properly mount and secure the camera to
the mounting surface.
2. Adjust the camera’s pan, tilt and position to achieve the desired view. To adjust the camera’s angle, loosen the pan/tilt/rotation
screw at the base of the camera. . The cameras’ max angles are:
Pan: 0° ~ 360°
Tilt: 0° ~ 90°
Rotation: 0° ~ 360°
3. The DWC-VA583WTIR camera includes a vari-focal p-iris lens with motorized zoom and auto-focus. The zoom and focus can
be controlled using the up the coax (UTC) communications. Simply connect the camera to a UTC enabled DVR and adjust the
camera’s zoom and focus remotely from the DVR.
4. Once the installation is complete, tighten the pan/tilt/rotation screw until it’s secure.
Quick Start Guide
1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:
a. Enter the camera’s OSD menu from a recorder supporting UTC
communication. Go to SETUP > OUTPUT > ANALOG MODE.
b. Set the camera’s analog signal output from the following
options:
• HD-A: supports 5MP/1944p @ 20fps and 12.5fps, 4MP/1440p
@ 30fps, 2.1MP/1080p @ 30fps and 720p @ 30fps.
• HD-T: supports 5MP/1944p @ 20fps, 4MP/1440p @ 30fps,
2.1MP/1080p @ 30fps and 720p @ 30fps.
• HD-C: supports 4MP/1440p @ 30fps, 2.1MP/1080p @ 30fps
and 720p @ 30fps.
• CVBS: supports up to 960H @ 30fps
c. Change CONFIRM to ON to save the changes.
d. Go to the EXIT menu and select SAVE&EXIT to save all changes.
The camera signal automatically.
STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN
THE CAMERA
Rev Date: 08/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Rotation 360°
Titling 90°
Panning 360°
NOTE: To use your Star-Light Plus™ 5MP cameras at a lower
resolution, you must use a VMAX® A1 Plus™ DVR to
access the camera’s menu due to the cameras being
set to 5MP as the default. A DVR that does not support
5MP resolution may recognize the camera, but will not
deliver a picture