Digital Watchdog Star-Light 960H DWC-B6563DIR User manual

12162013
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Bullet Camera
DWC-B6563DIR
DWC-B6563TIR550
DWC-B6563DIR
DWC-B6563DIR
DWC-B6563DIR
DWC-B6563TIR550
DWC-B6563TIR550
DWC-B6563TIR550
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.
2
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

Table of Contents
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
4
5
6-7
Inside the Box
Mount Installation Instructions
Connecting to Monitors
Control Board
Adjusting the Camera Angle
8
9
10
11
12
13-24
25
26-27
28-29
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
3

FEATURES*
960H CCD Image Sensor (960 Horizontal Pixels)
720 TV Lines [B/W], 700 TV Lines [Color]
2.8~12mm Varifocal Auto Iris Lens [DWC-B6563DIR]
5~50mm Long Range Varifocal Auto Iris Lens [DWC-B6563TIR550]
100ft Range IR with Intelligent Camera Sync, Smart IR [DWC-B6563DIR]
150ft Range IR with Intelligent Camera Sync, Smart IR [DWC-B6563TIR550]
Electronic Day & Night [DWC-B6563DIR]
TDN (True Day & Night) [DWC-B6563TIR550]
3D DNR (3D Digital Noise Reduction)
Star-Light (Super Low Light Technology)
HME (Highlight Masking Exposure)
SLC (Side-Light Compensation)
Programmable Privacy Zones (8) & Motion Detection
AGC / BLC / AWB
Easy Icon Driven OSD Menu with Built-in Joystick
IP66 Certified (Weatherproof)
Auto Sensing 24VAC/12VDC with Line Lock
Secondary Video-BNC Output
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
4

PARTS & DESCRIPTION*
1
2
3
4
Mounting Bracket
Camera Module
Sunshield Adjusting Screws
Sunshiled Cover
5
7
6
5
4
3
1
2
6
IR Module
Front Case
OSD Joystick Controller
7
Set Screw
5
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

DIMENSIONS IN MILLIMETERS (IN)*
DWC-B6563DIR
4.2 0.17
78.0 3.07
234.5 9.23
73.7 2.90
112.0 4.41 94.0 3.70
96.7 3.81
61.5 2.42
6
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

DIMENSIONS IN MILLIMETERS (IN)*
DWC-B6563TIR550
252 9.92
73.7 2.90
158.5 6.24 93.5 3.68
96.7 3.81
4.2 0.17
78.0 3.07
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
7

DWC-B6563DIR
DWC-B6563DIR
DWC-B6563DIR
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
INSIDE THE BOX*
Included with Bullet Camera:
1 4
User Manual Secondary Video-BNC Cable
2Mounting Template 5L-Key
3 4 Machine Screws and 4 Dry Wall Anchors
Bullet Camera
DWC-B6563DIR
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
07232013
8

Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
INSTALLATION INSTRUCTIONS*
1. Using the mounting template or your own camera,
mark and drill the necessary holes to mount the
bracket to a wall or ceiling.
2. Pull all necessary wires through and make the
proper connections.
3. Use the four (4) mounting screws to install
the camera on the wall or ceiling.
NPT 3/4” Pipe
*Installation Using a Junction Box
*Note: Electrical junction box and
required screws sold separately.
9

CONNECTING TO MONITORS*
Use the diagram below to connect to a Monitor or CRT Monitor properly.
12VDC/24VAC
CCTV Monitor
Second Video Output
Right
Left
Up
Down
Monitor
Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.
10
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

CONTROL BOARD*
Joystick: Controls the OSD menu.
Secondary Connector:
Video Output Connector for
On-Site Configuration
1
2Remove the camera’s lens cover by rotating it counter-clockwise.
Use the Joystick to control the camera’s OSD options.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
11

ADJUSTING THE CAMERA ANGLE*
CAUTION :
1
2Do not rotate more than 360o.
Do not unnecessarily twist too many times.
12
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

MODULE OSD MENU*
LENS
BACKLIGHT
AGC
0~20
DRC/ DEFOG
STARLIGHT
3D DNR
EXIT JUMP
EXPOSURE
PRIVACY SETUP
COLOR FUNCTION
MOTION
WB BAL. D&N MODE
CONTROL
B/W BURST
SMART IR
ANTI-SAT / SAT. AREA
OFF / ON
DELAY
MIRROR
SHARPNESS
GAMMA
SLC
0~20
POSI/NEGA
EXIT JUMP
COLOR GAIN
EXIT JUMP
EXIT JUMP
MANUAL / DC
OFF / BLC / HME
OFF / DRC/ DEFOG
OFF / x2 ~ x512
OFF / LOW / MID / HIGH
SAVE & EXIT / EXIT
ATW / MANUAL / PUSHLOCK
0~20
SAVE & EXIT / EXIT
AUTO / COLOR / B&W
AUTO / EXTERN
0 ~ 15
SAVE & EXIT / EXIT
OFF / ON
0 ~ 20
0.35 ~ 0.70
POSI / NEGA
SAVE & EXIT / EXIT
DAY & NIGHT
EXIT
CAMERATITLE SAVE
OFF / ON
SYNC RESTORE
INT EXIT
COMMUNICA.
CAM ID / ID DISP. / BAUDRATE /
PROTOCOL / UTC
LANGUAGE
ENGLISH
FONT COLOR
BLUE / GREEN / CYAN / RED /
MAGENTA / YELLOW / BLACK/
GRAY
SPECIAL
O.L.P.F / DPC
EXIT JUMP
SAVE & EXIT / EXIT
MOTION
OFF / ON
SENSITIV.
0 ~ 30
MOTION SET
AREA NO./ AREA USE / TOP/
BOTTOM / LEFT / RIGHT
EXIT JUMP
SAVE & EXIT / EXIT
COLOR
BLACK / GRAY-1/ GRAY-2/
GRAY-3/ GRAY-4/ WHITE /
YELLOW / GREEN / BLUE /
RED / CYAN / MAGNETA
PRIVACY SET
AREA SET / DISPLAY / TOP /
BOTTOM / LEFT / RIGHT /
RET/INI.
EXIT JUMP
SAVE & EXIT / EXIT
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
13

*
NOTE: Both MANUAL and DC mode have FOCUS SET. You
can adjust the focus by finding the highest number on the FOCUS
SET. See page 15 for focus information.
MANUAL Lens Submenu
EXPOSURE
LENS
Manual Manual mode supports the fixed board lens or the
manual iris lens.
DC DC mode supports the auto-iris varifocal lens.
Brightness: Adjust the camera’s brighness from 0~20. The higher the
number, the brighter the image will appear.
Shutter: Sets the shutter speed levels from 1/60 to 1/120000.
*For LENS-MANUAL Mode, the default SHUTTER is AUTO.
*For LENS-DC Mode, the default SHUTTER is 1/60. Select DC-AUTO for
outdoor use.
FLC: Enable or disable to adjust the camera’s view and prevent the
image from flickering.
DC Lens Submenu
14
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

EXPOSURE
BACKLIGHT
OFF
BLC BACK LIGHT COMPENSATION
If BLC is selected, adjust the following options in the submenu:
- LEVEL: Set the BLC level from the available options: LOW/ MIDDLE/ HIGH)
- DISPLAY: Selet to show or hide the BLC mask.
- POSITION: Set the BLC masks’ size and position.
TOP: Set level from 0~54. The higher the number, the higher the
top border of the BLC mask will be in the camera’s view.
BOTTOM: Set level from 1~55. The higher the number, the lower
the bottom border of the BLC mask will be in the camera’s view.
LEFT: Set level from 0~217. The lower the number, the closer the
BLC mask will be to the camera’s left border.
RIGHT:Set level from 1~218. The lower the number, the closer the
BLC mask will be to the camera’s right border.
- RET/ INI.: Select whether to return to the main menu, or reset the BLC settings
to factory default.
HME HIGHLIGHT MASKING EXPOSURE
HME masks highlights to allow objects to appear clearly
on the screen. If ON is selected, HME levels are
adjustable. The lower the setting, the darker the masking
areas. Select from: LOW / MIDDLE / HIGH.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
15

EXPOSURE
DRC DYNAMIC RANGE COMPRESSOR
DRC enables dark spots in images to become more visible without overexposing the
bright spots to create one perfect image.
- DEFOG: AUTO / Manual: If AUTO is selected, the WDR and DRC levels will be set
automatically based on the environment. If MANUAL is selected, set the WDR and DRC
level from LOW / MIDDLE / HIGH.
- MODE: * ONLY DAY: DRC and WDR will work in day time.
* ALL DAY: DRC and WDR will work in day and night time.
AGC
1~20 AUTO GAIN CONTROL
AGC enhances the picture brightness in low light conditions. A higher level AGC
setting makes the images brighter; however, it could increase the amount of noise.
STARLIGHT Automatically activates slow shutter function when the image is too dark.
OFF / x2 ~ x512 High values are not recommended as they may causes the image to lag.
Starlight menu cannot be controlled if the SHUTTER setting is above 1/60.
3D DNR 3D DIGITAL NOISE REDUCTION- 3D-DNR reduces the noise on the screen
OFF/ LOW/ MID/ HIGH in low light conditions and allows for clearer images, even at night.
16
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

COLOR
WB MODE
ATW Auto Tracking White Balance Control mode compensates for color temperature changes
between 2500K and 9500K.
PUSHLOCK Pushlock is to fix the white balance based on the lighting.
MANUAL Users can control the white balance manually by changing RED GAIN and BLUE
GAIN (see below).
RED GAIN
0 ~ 40 Adjusts the amount of red in the image.
BLUE GAIN
0 ~ 40 Adjust the amount of blue in the image.
COLOR GAIN
Set the color gain from 0~20.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
17

D&N MODE
DAY & NIGHT
AUTO / In AUTO mode, the camera switches between day and night automatically depending
COLOR / on light level. If COLOR is selected, the camera always stays in day/color mode.
B&W If B&W is selected, camera always stays in night/B&W mode. If AUTO is selected,
please define the following settings:
CONTROL: AUTO/EXT. If using IR LEDs built into the camera, select
AUTO. If using external IR LEDs separately, select EXT.
Adjust the following submenu options:
* EXT SIGNAL: Select from CDS or LOW/HIGH.
If CDS is selected: Day & Night will work by CDS signal level.
If LOW/ HIGH is set for EXT SIGNAL: Day & Night will work by
CDS’s Low/High signal.
- CDS D>N : Set D>N level from 0 ~ 40. Adjusts the light level at
which the camera switches from day to night. Higher values, the lower the light level.
- CDS N>D : Set N>D level from 0 ~ 20. Adjusts the light level at which the camera
switches from night to day. This should be lower than the value of D>N above.
- NIGHT S/W : Decide the Low/High signal of CDS.
*EXT LED: If you want to turn off the external LED by force, you can change the value
from AUTO to OFF.
DELAY
0 ~ 15 Sec. Time interval delay before switching from day mode to night mode.
B/W BURST
OFF / ON If ON is selected, the camera provides a color burst signal in night mode.
SMART IR - ANTI-SAT: Select level value from 1 ~ 20.
- SAT. AREA : Set SMART IR area from 0 ~ 20.
18
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

FUNCTION
MIRROR
OFF
MIRROR Reflects the camera horizontally.
Mirror ONMirror OFF
SHARPNESS
0 ~ 30 Sets the image sharpness. The higher the number, the sharper the image.
GAMMA
0.35 ~ 0.7 Select the desired gamma level. 0.45 is default setting.
POSI / NEGATIVE
OFF / ON If NEGATIVE is enabled, the camera’s image
will appear in negative colors.
SLC (SIDE LIGHT COMPENSATION)
0~20 Increase the brightness on sides of the image.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
19

MOTION
The camera can detect the movement and display an alarm on the screen when movement is detected.
MOTION
OFF / ON Select to enable or disable the camera’s motion detection. If ON is selected:
SENSITIV.
0 ~ 30 Sensitivity level of the motion detection is adjustable. Motion Detection will be more
sensitive at a higher number.
MOTION SET
- Area Number: The camera supports up to 4 different motion detection masks. Select which ones to display.
- Area Use: Select which one of the motion areas to enable.
- TOP: The higher the number, the higher the top border of the mask will be in the camera’s view.
- BOTTOM: The higher the number, the lower the bottom border of the mask will be in the
camera’s view.
- LEFT: The lower the number, the closer the mask will be to the camera’s left border.
- RIGHT: The lower the number, the closer the mask will be to the camera’s right border.
- RET/ INI.: Select whether to return to the main menu, or reset the motion settings to factory default.
20
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]