Digital Watchdog V1362DIR User manual

Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
ABOUT MANUAL
06212011
User Manual
Vandal Dome Camera
V1362DIR / V1363TIR / V1382TIR
e
r
a
,
p
l
e
a
s
s
e
r
e
a
d
t
h
h
i
s
m
an
u
a

2
GGDonot open or modify.
GGDonot open the case except during maintenanceand installation,
for it may bedangerous and can cause damages.
GDonot put objects into the unit.
GGGG
Keep metal objects and ammablesubstances from entering the camera. Itcan cause re, short- circuits,
or other damages.
GGGBe careful when handling the unit.
Toprevent damages, do not drop the camera or subjectit to shockor vibration.
Donot install near electric or magnetic elds.
Protectfrom humidity and dust.
Protectfrom high temperature.

Be careful when installing near the ceiling of akitchen or aboiler room, as the temperature may rise to
high levels.
Cleaning
GGGGGToremovedirt from the case, moisten asoft cloth with asoft detergent solution and wipe.
Mounting Surface
GGGGGThe material of the mounting surfacemust bestrong enough to support the camera.
PRECAUTIONS

3
Before sending your camera out for repair, check the items below.
If the problem persists after checking these items, contact your service
center.
No Video
Is the coaxial cable attached securely?
Is there adequate illumination?
Out-of-Focus Video
Is the lens in focus?
Is the lens dirty?
(commercially available) and a soft cloth or lens cleaning paper.
WARNING :TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
TROUBSHOOTING

4
DIMENSIONSIN MILLIMETERS*
6.5
41.3
103.1
109.6
91.0
85.0
ø145
ø4.5
ø5.0
117.0
125.0
85.0
91.0
VIDEO (YELLOW)
DC 12V or AC24V
5mm TWIST SOLDERING
L= 300mm
BNCJACK
BLACK
RED

5
INSTALLATION*
the Fixing Screws (D).
1.
2. Separate the Upper Case (A) and the Base (E).
3. Detach the Gimbal (C) from the Base (E).
4. Cut a hole in the ceiling for routing the cables.
5. Place the Base (E) horizontally against the ceiling and
drill the screwholes at the two marked positions.
6. Pass the Power Cable (F) and Video Cable (G) from the
camera unit through the cable hole in the ceiling.
7. Align the screwholes of the camera unit with the
holes in the ceiling. Secure the camera to the ceiling
with the two screws.
8. FixGimbal (C) to the Base (E).
9. Install and adjust the camera unit.
10. Adjust the dome liner to showthe lens through the
11. Attach the Upper Case (A) with the Base (E) and tighten
Loosen the Fixing Screw(D), using a screwdriver.
camera window, and then x it to the Base (E).
F
G
E
C
B
A
D

6
CONNECTION*
CAUTION : CHECK FOR POLARITY WHENUSING ADC12VPOWER SUPPLY.
DC12V
DC12V/ AC24V
300.0

7
CAMERASETTINGS*
1. Set the zoom level to the desired position by moving the Zoom Lever.
2. Set the focus, using the Focus Lever.
GLENSADJUSTMENT
1. Focus Lever
2. Zoom Lever

CAMERA SETTING FORSIDEOSD CONTROL BOARD
*
SW
V1362DIR, V1363TIR, V1382TIR
RIGHT
LEFT
UPDOWN
CON1
CON2
FUNCTIONAL OF CONTROL BOARD
[1] SW
Functional control of O.S.D(On Screen Display)
[2] CON1
Second Video output connector
[3] CON2
RS-485 connector
8

NOTE: PRESS
EFAULT IS“001”FOR
GGGGGGGGGGPRESS TO ACCESS THE MENU
NOTE : THE CAMERA ID IS A DIGIT NUMBER.
REMOTECONTROL*
1. Set the Camera iDin the OSD menu. The default
setting is 001. NOTE:
you must reset the power for the newsettings to
apply. Once you reset the power, the camera will
recognize the newCamera ID.
2. If you press the KEY Button, the camera display
will turn into the standby image. NOTE:The LED
3. Input the same number used as the Camera ID to
the Remote Controller. After the number has been
input, the LEDlight will turn on, and the remote
controller will be ready to use. NOTE:The ID
number is 3digits.
4. The ZOOMIn (+) and ZOOMOut (-) Keys are used
to control the zoom of your camera lens and to
select the zoom area of alarm function. Select the
area where you wish to observe the movement of
objects.
5. Select the zoom range by pressing the WIDE (7)
Key. Save the zoom range by pressing the TELE (8)
Key. NOTE: If the zoom range is smaller than the
alarm standby range, the zoom range setting will
not be saved.
Menu Access and Control
Motion Alarm
ON / OFF
Key Button
ID Buttons
Zoom Function Control
GREMOTECONTROL Instructions
9

MODULEOSD MENU*(V1362DIR)
EXPOSURE COLORDAY&NIGHT
BRIGHTNESS
SHUTTER
BLC
AGC
WB MODED&N MODE
FUNCTION MOTION PRIVACY
MIRROR
SHARPNESS
GAMMA
SLC
HME
DRC
ALARMMASK 1
MASK 2
MASK 3
MASK 4
COLOR SET
SYNCSETUPEXIT
SYNCCAMERA ID
TITLE EDIT
TITLE RESET
TITLE POSITION
DPC SET
LANGUAGE
PC CONT.
EXIT
SAVE & EXIT
FACTORY RESET
10