Digital Watchdog DWC-B1365T User manual

07062012
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
PIXIM Bullet Camera
DWC-B1365T

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

Table of Contents
3
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Mount Installation Instructions
Connecting to Monitors
Control Board
Adjusting the Camera Lens
4
5
6
7
8
9
10
11
13-24
25
26-27
28-29
Adjusting the Camera Angle 12

4
FEATURES*
1/3” PIXIM Seawolf CMOS Sensor
690 Horizontal TV Lines
3.3~12mm Varifocal Auto Iris Lens
TDN (True Day and Night/IR Cut Filter)
3D-DNR (3D Digital Noise Reduction)
Powerful Wide Dynamic Range
Ultra Low Light Sensitivity
Smear Canceling Circuit
AGC / BLC / AWB
Programmable Privacy Zones (6) & Motion Detection
OSD Menu with Built-in Joystick
IP66 Certified (Weatherproof)
No Fog or Condensation under Any Weather Condition
Auto Sensing 12VDC/24VAC with Line Lock
Secondary Video-BNC Output
Ball Neck Bracket (Simple Camera Positioning)
External Lens and OSD Control

Set Screw
RS 485
NO IR
IR
5
PARTS & DESCRIPTION*
1 2 4 65 7 8
13
12
10
9
3
11
1Front Case
Zoom & Focus Housing
Sunshield
Lens
Rear Case
Control Board
Control Cap
2
3
4
5
6
8Double Arm Bracket
Second Video-BNC Output Connector
Power Input Connector (Dual Voltage)
Assembly Screw
Mounting Screw
Set Screw
9
10
11
12
13
7

6
DIMENSIONS IN MILLIMETERS (IN)*
230(9.06”)
86.5
(3.41”)
122(4.80”) 96.5(3.80”)
68.0
(2.68”)
68.0(2.68”)
78.0(3.07”)
5.0(0.2”)
96.0(3.78”)

7
INSIDE THE BOX*
Included with B1 Bullet Camera
1
2
3
4
5
6
User Manual
Mounting Template
4 Machine Screws and 4 Dry Wall Anchors
Secondary Video-BNC Cable
L-Key
Double-Sided TORX-T20 Hex Key
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Bullet Camera
DWC-B1363D
DWC-B1363TIR

8
SURFACE MOUNT INSTALLATION INSTRUCTIONS*
Use the 4 mounting screws to install the camera on the
wall or ceiling.
Then, follow the next step on pages 9-12.
NPT 3/4” Pipe

*Installation Using a Junction Box
*Note: Electrical junction box and required screws are sold separately.

Use the diagram below to connect to a Monitor or CRT Monitor properly.
12VDC/24VAC
Monitor
CCTV Monitor
Second Video Output
Right
Left
Up
Down
Power Connection - 12VDC/24VAC Dual Voltage (Auto Polarity Detection and Protection)
All cameras are equipped with a second video output for on-site configuration.
9
CONNECTING TO MONITORS*

10
Joystick: Controls the OSD menu.
Secondary Connector:
Video Output Connector for
On-Site Configuration
CONTROL BOARD*
Remove clear plastic ring from the control cap.
Turn control cap counter-clockwise until cap separates completely from the camera body.
1
2