DigitaLinx IPEX5001-D User manual

11675 Ridgeline Dr.
Colorado Springs, CO 80921
Rev 191115 Toll-Free: 800-530-8998
Fax: [phone]
[e-mail]
IPEX5000 Series Install Guide
This guide is for basic installaon only.
For complete Digitalinx IP Deployment Guide go to www.libav.com or use a
QR reader to access the manual via QR code below.
Scan QR Code with your Smart-phone or Tablet

IPEX5000 Series Quick Install Guide
3
1. Read these instrucons – All the safety and operang instrucons should be read before this product is operated.
2. Keep these instrucons – The safety and operang instrucons should be retained for future reference.
3. Heed all warnings – All warnings on the appliance and in the operang instrucons should be adhered to.
4. Follow all instrucons – All operang and use instrucons should be followed.
5. Do not use this apparatus near water – The appliance should not be used near water or moisture – for example, in a wet
basement or near a swimming pool, and the like.
6. Clean only with a dry cloth.
7. Do not block any venlaon openings. Install in accordance with the manufacturer’s instrucons.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)
that produce heat.
9. Do not defeat the safety purpose of the polarized plug. A polarized plug has two blades with one wider than the other.
The wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and at the
point where it exits from the apparatus.
11. Only use aachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the
apparatus. When a cart or rack is used, use cauon when moving the cart/ apparatus combinaon to avoid injury
from p-over.
13. Unplug the apparatus during lighng storms or when unused for long periods of me.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any
way, such as; the power-supply cord or plug is damaged, liquid has been split or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. CAUTION: Servicing instrucons are for use by qualied service personnel only. To reduce the risk of electric shock, do
not perform any servicing other than that contained in the operang instrucons unless you are qualied to do so.
16. Do not install this equipment in a conned or built-in space such as a book case or similar unit. The equipment must
remain in well venlaon condions. Venlaon should not be impeded by covering the venlaon openings with items
such as newspaper, table-cloths, curtains etc.
17. WARNING: Only use aachments/accessories (such as the baery etc.) specied or provided by the manufacturer.
18. WARNING: Refer to the informaon on the underside of the enclosure for electrical and safety informaon before
installing or operang the apparatus.
19. WARNING: To reduce the risk of re or electric shock do not expose this apparatus to rain or moisture. The apparatus
shall not be exposed to dripping or splashing and objects lled with liquids, such as vases, shall not be placed on apparatus.
20. CAUTION: Danger of explosion if baery is incorrectly replaced. Replace only with the same or equivalent type.
21. WARNING: The baery shall not be exposed to excessive heat such as sunshine, re or the like.
22. WARNING: The all-pole mains switch located on rear panel is used as the disconnect device, the switch shall remain
readily operable.
23. WARNING: DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD.
24. Keep new and used baeries away from children. If the baery compartment does not close securely, stop using the
product and keep it away from children.
25. If you think baeries might have been swallowed or placed inside any part of the body, seek immediate medical
aenon.
Important Safety Instrucons

IPEX5000 Series Quick Install Guide
4
26. When the apparatus is not in use or during its relocaon, take care of the power cord and plugs; e.g. e up the power
cord with cable e or similar. The e must be free from sharp edges and the like that might cause abrasion of the power
cord. When put into use again ensure the power cord and plugs are not damaged. If any damage is found the power cord
and plugs should be replaced by items either specied by the manufacturer or that have same characteriscs as the original
items.
27. This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the
presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sucient magnitude to
constute a risk of electric shock.
28. WARNING: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts
inside. Refer servicing to qualied personnel.
29. The exclamaon point within an equilateral triangle is intended to alert the user to the presence of important
operang and maintenance instrucons in the literature accompanying the appliance.
30. Protecve earthing terminal. The apparatus should be connected to a mains socket outlet with a protecve
earthing connecon.
31. CAUTION: To prevent electric shock hazard, replace grille. (CSA 60065, clause 5.3A)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR

IPEX5000 Series Quick Install Guide
5
The Digitalinx IP IPEX5001 transmits HDMI video and audio over a 1 gigabit network infrastructure using JPEG2000
encoding with a variable data rate at an average of 250 Mbps with peak values up to 850Mbps. The IPEX5001
supports video signals up to 4K at 60 Hz 4:2:0 / 8 bit deep color, 4K at 24Hz 4:2:0 / 10 bit deep color for HDR10
support, HDCP 2.2 and mulchannel audio support. An analog audio input port embeds analog audio with the
video content, such as a DVI video source. An analog audio output port de-embeds stereo 2 channel audio from
the HDMI content, while sll passing stereo 2 channel audio to the HDMI output.
The IPEX5001 supports PoE power and can be powered remotely via PoE network switch eliminang the need
for a nearby power outlet. The RS232 port relays commands from the IPEXCB controller and operates in a pass
through mode to control a third party device such as a TV display or HDMI switcher. The USB host port connecon
is for connecng USB host devices such as a computer that is USB 2.0 Full Speed compliant up to 12Mbps that
can communicate with client side devices connected to a decoder. USB roung follows the video route by default
however USB communicaon can be free routed via API. The IPEX5001 features bi-direconal IR support which
follows the video route or can be routed freely via API command.
The IPEX5001 requires a single IPEX5002 for a point to point installaon. When mulple IPEX5001
and/or IPEX5002 devices are in a system, an IPEXCB interface will be required.
Product Overview
IPEX5001 Encoder
The Digitalinx IP IPEX5001-WP-W transmits HDMI or VGA video and audio over a 1 gigabit network infrastructure
using JPEG2000 encoding with a variable data rate at an average of 250 Mbps with peak values up to 850Mbps.
The IPEX5001-WP-W supports video signals up to 4K at 60 Hz 4:2:0 / 8 bit deep color, 4K at 24Hz 4:2:0 / 10 bit deep
color for HDR10 support, HDCP 2.2 and mulchannel audio support. An analog audio input port embeds analog
audio with the video content, such as a DVI video source. An analog audio output port de-embeds stereo 2 channel
audio from the HDMI content, while sll passing stereo 2 channel audio to the HDMI output. The HDMI and VGA
inputs on the IPEX5001-WP-W are auto switching and follow the last in / rst out method and must be physically
connected / disconnected to engage the auto switch.
The IPEX5001-WP-W supports PoE power and can be powered remotely via PoE network switch eliminang the
need for a nearby power outlet. The RS232 port relays commands from the IPEXCB controller and operates in a pass
through mode to control a third party device such as a TV display or HDMI switcher. The USB host port connecon
is for connecng USB host devices such as a computer that is USB 2.0 Full Speed compliant up to 12Mbps that can
communicate with client side devices connected to the decoder. USB roung follows the video route by default
however USB communicaon can be free routed via API. The IPEX5001-WP-W features a built in IR receiver built in
on the plate, IR follows the video route or can be routed freely via API command.
IPEX5001-WP-W Encoder

IPEX5000 Series Quick Install Guide
6
The Digitalinx IP IPEX5002 receives HDMI video and audio over a 1 gigabit network infrastructure using JPEG2000
encoding from the IPEX5001 and IPEX5001-WP-W encoder. The IPEX5002 outputs video signals navely from
source or can be scaled to 1080p or 4K at 24/30Hz 4:4:4 with HDR10, HDCP 2.2 and mulchannel audio support.
An analog audio output port de-embeds stereo 2 channel audio from the HDMI content while sll passing stereo 2
channel audio to the HDMI output. Depending on the needs of the installaon, mulple IPEX5002 devices can be
congured to make a video wall up to a 16x16 conguraon.
The IPEX5002 supports PoE power and can be powered remotely via PoE network switch eliminang the need for a
nearby power outlet. The RS232 port relays commands from the IPEXCB controller and operates in a pass through
mode to control a third party device such as a TV display or HDMI switcher. The USB client port connecons is for
connecng USB client devices such as an interacve white board or HID devices that is USB 2.0 Full Speed compliant
up to 12Mbps that can communicate with the host device connected to an encoder. USB roung follows the video
route by default however USB communicaon can be free routed via API. The IPEX5001 features bi-direconal IR
support which follows the video route or can be routed freely via API command.
The IPEX5002 requires a single IPEX5001 for a point to point installaon. When mulple IPEX50012
and/or IPEX5001 devices are in a system, an IPEXCB control box will be required.
IPEX5002 Decoder
The Digitalinx IP IPEX5001-D transmits HDMI video and audio over a 1 gigabit network infrastructure using JPEG2000
encoding with a variable data rate at an average of 250 Mbps with peak values up to 850Mbps. The IPEX5001-D
is Dante enabled meaning that the encoder can on ramp two channel stereo audio either from the embedded
HDMI audio stream or the analog audio 3.5mm input onto a Dante audio network. The mulcast video and Dante
audio IP streams are integrated into one Ethernet cable simplifying networked audio and video soluon into one.
An analog audio output port de-embeds stereo 2 channel audio from the HDMI two channel stereo embedded
stream, while sll passing stereo 2 channel audio to the HDMI output. The IPEX5001-D supports video signals up to
4K at 60 Hz 4:2:0 / 8 bit deep color, 4K at 24Hz 4:2:0 / 10 bit deep color for HDR10 support and HDCP 2.2 support.
The IPEX5001-D supports PoE power and can be powered remotely via PoE network switch eliminang the need
for a nearby power outlet. The RS232 port relays commands from the IPEXCB controller and operates in a pass
through mode to control a third party device such as a TV display or HDMI switcher. The USB host port connecon
is for connecng USB host devices such as a computer that is USB 2.0 Full Speed compliant up to 12Mbps that can
communicate with client side devices connected to the decoder. USB roung follows the video route by default
however USB communicaon can be free routed via API.
IPEX5001-D Encoder

IPEX5000 Series Quick Install Guide
7
Package Contents per Device
1. Installaon Guide
2. Power Supply with US, UK, EU, and AU adapters
3. 3-pin Removable Screw Terminal
4. Mounng Ears (2 ea)
5. IR Emier
6. IR Receiver
1. Installaon Guide
2. Power Supply with US, UK, EU, and AU adapters
3. 3-pin Removable Screw Terminal
4. Mounng Ears (2 ea)
5. IR Emier
6. IR Receiver
1. Installaon Guide
2. (1) Phoenix 2 pin male connector (3.5mm)
3. (1) 2 gang wall plate decora plasc cover with screws
4. (4) Mounng screws
1. Installaon Guide
2. Power Supply with US, UK, EU, and AU adapters
3. 3-pin Removable Screw Terminal
4. Mounng Ears (2 ea)
5. IR Emier
6. IR Receiver
IPEX5001
IPEX5001-D
IPEX5001-WP-W
IPEX5002

IPEX5000 Series Quick Install Guide
8
Front and Rear Panels
IPEX5001 Front Panel
12 3 4
1. Power indicator
2. Status indicator
3. RS232 Funcon Switch
4. DIP Switch for ID Modes
IPEX5001 Rear Panel
A. 12V DC power input
B. RESET buon
C. LAN connecon with PoE support
D. Analog audio input
E. Analog audio output
F. RS232 connecon
G. USB Host connecon
H. HDMI input
I. HDMI output
J. IR input
K. IR output
IN
ANALOG AUDIO
OUT USB HOST
A B C D E F G H I J K

IPEX5000 Series Quick Install Guide
9
IPEX5001-WP-W Front Panel
1. VGA input port
2. Audio input port (embedded with VGA source)
3. HDMI input port
4. Link LED
• When SOLID: encoder is connected to connected to both an acve source and decoder
• When Blinking: encoder is disconnected from an acve source or decoder
• When OFF: encoder is powered o or network is down
5. Power LED
• When SOLID: device is powered on
• When OFF: encoder is powered o or network is down
6. Factory reset
7. IR receiver / sensor
8. RS232 control port
9. USB host port
1. DC12 DC power input
2. LAN connecon with PoE support
IPEX5001-WP-W Rear Panel

IPEX5000 Series Quick Install Guide
10
IPEX5001-D Front Panel
IPEX5001-D
12 3 4
1. Power indicator
2. Status indicator
3. RS232 Funcon Switch
4. DIP Switch for ID Modes
IPEX5001-D Rear Panel
A. 12V DC power input
B. RESET buon
C. LAN / Dante connecon with PoE support
D. Analog audio input
E. Analog audio output
F. RS232 connecon
G. USB Host connecon
H. HDMI input
I. HDMI output
J. IR input
K. IR output
IN
ANALOG AUDIO
OUT USB HOST
LAN / Dante
A B C D E F G H I J K

IPEX5000 Series Quick Install Guide
11
IPEX5002 Front Panel
USB DEVICE
12 3 4 5
1. Power indicator
2. Status indicator
3. RS232 Funcon Switch
4. DIP Switch for ID Modes
5. USB ports for keyboard or mouse
IPEX5002 Rear Panel
A. 12V DC power input
B. RESET buon
C. LAN connecon with PoE support
D. Analog audio output
E. RS232 connecon
F. HDMI output
G. IR input
H. IR output
A B C D E F G H

IPEX5000 Series Quick Install Guide
12
System Consideraons
Gigabit Switch Features
Gigabit Switch Size(s)
A high quality, managed Level 2 gigabit PoE switch with a high bandwidth backplane should be used in the
installaon. The two primary features to look for in the switch are support for mulcast with jumbo frames and
support for IGMP snooping, which are required technologies for stable video signals.
Be sure to verify the PoE gigabit switch can provide adequate waage (PoE budget) to support all IPEX5000 devices
connected to a switch. Each IPEX5000 requires 6w-9w of PoE budget to operate appropriately.
When calculang the size of switch needed, the following devices need to be considered:
1. Number of sources
2. Number of displays
3. IPEXCB
4. Wireless access point for iPad app or Windows app (oponal)
5. Hardwire port for Windows app (oponal)
System Bandwidth
External Devices
250-850 Mbps should be considered when calculang the bandwidth for a 4k video stream. 150-750 Mbps should
be considered when calculang the bandwidth for a 1080p/60 video stream. These values cover the encoded
stream plus packet overhead. When using mulple encoders on a mul switch environments it is important to load
balance the streaming encoders evenly on each switch to allow for proper throughput. A 10Gb uplink between one
switch to another can typically accommodate 10-12 encoders streaming 4K video content in this type of network
infrastructure.
Due to the nature of JPEG2000 compression, the IPEX5000 encoding method is VBR (Variable Bit Rate). In a VBR
stream, the encoder will transmit dierent bit rates of data depending on how much informaon is present in the
parcular frame of video, while averaging the stream to the bandwidth hardcoded into the chipset. A solid color
frame will use less bandwidth than a mulcolor frame of video.
It may be necessary to use external HDMI devices in conjuncon with the DigitalinxIP video system to create
specic and customized funconality for an end user. When using devices such as audio de-embedders, extenders
or HDMI distribuon systems with DigitalinxIP devices it is suggested that custom HDMI circuits be tested before
deployed in the eld to address any interoperability, EDID and HDCP issues that may arise.

IPEX5000 Series Quick Install Guide
13
IPEXCB Controller
System Control
Heat and Venlaon
Backup Power
HDMI CEC
LAN Cabling
Source Content Resoluon
In addion to the gigabit switch, the IPEXCB is required for the encoders and decoders to communicate with each
other regardless of system layout, such as one to many.
There are mulple ways to control the system once installaon is complete. There is the DigitalinxIP Control
soware for iPad and Windows. While not recommended, the IPEXCB can be controlled through a web browser. A
third party controller can communicate directly with the IPEXCB via the LAN (CONTROL) port or via RS232.
All electronics generate heat, and excessive heat can cause electronic devices to fail prematurely. The IPEX5001
and IPEX5002 devices are passively cooled and should not be stacked on top of each other or other devices. Please
leave at least 1 ½ inches (approximately 35-40 mm) of open space by the side vents to provide adequate airow.
The gigabit switch will likely have acve cooling. Please follow the manufacturer’s installaon instrucons for
proper mounng in an equipment rack.
It is always a good pracce to install a high quality UPS (uninterrupble power supply) with line ltering with
expensive electronics. The UPS can provide “clean” power to all the devices in the equipment rack while also
providing enough me to properly shut down connected devices in the event of an extended power failure.
The IPEX5002 can turn on and turn o connected displays via CEC. This technology has been a part of the HDMI
specicaon for years. The Digitalinx IP Control soware for Windows and iPad can turn on and o the displays for
easy end user control.
For all LAN cabling, the EIA/TIA-568B crimp paern must be used on Category 5e or greater cable. In areas with
large amounts of electromagnec (EM) or radio frequency (RF) interference, a shielded variety of Category 5e or
greater cable is recommended with shielded connectors on both ends of the selected cable. For high bandwidth
content such as 4K content, it is suggest that Cat6 or greater be used.
Even though the IPEX5000 series devices support 1080i, this resoluon may cause arfacts through the encoding
process. Please set the output resoluon of devices showing 1080i content to 720p or 1080p.
TIA/EIA-568B
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
1 8

IPEX5000 Series Quick Install Guide
14
This method will also work with a one to many installaon.
Installaon Instrucons
1. Connect Category 5E or greater twisted pair cable with the TIA/EIA-568B crimp paern between the LAN
port on the encoder (IPEX5001) and the decoder (IPEX5002).
2. Set the DIP switches on the front of the IPEX5001 and IPEX5002 to the same value, other than all up.
3. Connect the included power supply to the 12V DC power input of the encoder and decoder.
4. Connect an HDMI cable between the display and the decoder (IPEX5002).
5. Connect an HDMI cable between the source and the encoder (IPEX5001).
6. Power on aached audio/video devices.
7. Connect the included power supply connected to the encoders and decoders to an AC outlet.
1. Disconnect power from the IPEX5001 and IPEX5002.
2. Set the DIP switches on the front of the IPEX5001 and IPEX5002 to all up.
3. Connue with Basic Matrix Installaon instrucons.
Point to Point Installaon - IPEX5001 / IPEX5002
Reset Point to Point Installaon to Factory Default
Basic Matrix / Networking Installaon
1. Congure the gigabit switch for IP video operaon. Liberty has guides for many common switch manufacturers
on the IPEXCB product page on the Liberty website (www.libav.com).
2. Turn o power and disconnect the audio/video equipment by following the manufacturer’s instrucons.
3. Turn o power to the congured switch.
4. Connect Category 5E or greater twisted pair cable with the TIA/EIA-568B crimp paern between the LAN
port on the encoder(s) (IPEX5001 / IPEX5001-WP-W / IPEX5001-D) and the gigabit switch.
5. Connect Category 5E or greater twisted pair cable with the TIA/EIA-568B crimp paern between the LAN
port on the decoder(s) (IPEX5002) and the gigabit switch.
6. If the gigabit switch cannot provide power or enough power to the IPEX5001 / IPEX5001-WP-W / IPEX5001-D
or IPEX5002, connect the included power supply to the 12V DC power input of the device. If the gigabit
switch cannot provide enough power, disable the PoE funcon of the connected LAN ports on the switch.
7. Connect an HDMI cable between the display and the decoder (IPEX5002).
8. Connect an HDMI cable between the source and the encoder (IPEX5001 / IPEX5001-WP-W / IPEX5001-D).
9. Power on aached audio/video devices.
10. Apply power to the gigabit switch.
11. If the gigabit switch cannot provide power to the encoders or decoders, connect the included power supply
connected to the encoders and decoders to an AC outlet.

IPEX5000 Series Quick Install Guide
15
RS232 Connecons
Analog Audio Connecons
USB Connecons
IR Connecons
To use the RS232 control transport capabilies of the IPEXCB or the RS232 extension capabilies of the encoders
and decoders, connect the TX, RX, and ground control signal wires to the removable 3-pole terminal block. Consult
the manual of the source or display device(s) to determine which pins the TX and RX signals are carried on. Be sure
to always connect TX to RX and RX to TX.
The analog audio input and output connecons on the IPEX5001 / IPEX5001-D and the analog audio output
connecons on the IPEX5002 use standard 3.5 mm TRS connectors.
Note: Two channel audio in/out capability is only achieved when using the 2CH Stereo EDID seng in the Digitalinx
IP Congurator soware under EDID SETTINGS. Please see the Digitalinx IP Deployment Guide for conguring this
funconality.
The IPEX5000 system is USB 2.0 Full Speed compliant up to 12Mbps
The USB Host port on the IPEX5001 / IPEX5001-D / IPEX5001-WP-W is provided to allow control of a PC source
from a remote locaon. The USB Device ports on the IPEX5002 are provided to add keyboard, mouse or interacve
white board control for the host PC connected to the routed encoder.
The USB signal from the decoder to the encoder follows the video route by default however this can be free routed
using the DigitalinxIP API. See DigitalinxIP Programming Guide online at libav.com
The IR connecons on the IPEX5000 encoders and IPEX5002 provide a means to control remote IR equipment. The
IR signals between the IPEX5000 encoders and IPEX5002 follow the video route however IR can be free routed via
API. See DigitalinxIP Programming Guide online at libav.com
Please ensure power is disconnected from the encoders and decoders before connecng the IR receiver to the IR
input ports on the devices.
TX
G
RX
RXD
TXD
GND
IPEX5001 or
IPEX5002
Source or
Display
IPEX5001 / IPEX5001-D
IPEX5002
IPEX5001-WP-W

IPEX5000 Series Quick Install Guide
16
IPEX5001 Technical Specicaons
Input/Output Connecons
HDMI Input One (1) HDMI Type A Receptacle
HDMI Output One (1) HDMI Type A Receptacle
LAN One (1) 8P8C port (Shielded RJ45)
Power One (1) 5.5 mm OD, 2.6 mm ID Threaded Barrel
RS232 Port One (1) 3-pin Removable Terminal Block Connector
USB Device One (1) USB Type B Port
Audio Input One (1) 3.5 mm TRS Receptacle
Audio Output One (1) 3.5 mm TRS Receptacle
IR Input One (1) 3.5 mm TRS Receptacle
IR Output One (1) 3.5 mm TRS Receptacle
Reset One (1) Momentary Push Buon
Mode One (1) Two Posion Slider Switch
DIP One (1) Four Posion DIP Switch
Supported Audio, Video and Control
Video Resoluons SMPTE: 480p, 576p, 720p, 1080i, 1080p, 2160p/30 (4:4:4), 2160p/60 (4:2:0)
VESA: Resoluons up to 1920x1200
Color Depth: 24, 30, 36 bit
Video Compliance HDMI 1.4 and HDCP 1.4/2.2
Embedded Audio Up to PCM 8 channel, Dolby Digital True HD, DTS-HD Master Audio, Dolby Atmos and DTS-X
ARC (Audio Return Channel) No
HEC (HDMI Ethernet Channel) No
CEC (Consumer Electronics Control) No
Supported Baud Rates 2400, 4800, 9600, 19200, 38400, 57600, 115200
USB Compliance USB 2.0 Full Speed up to 12Mbps
Streaming Signal Characteriscs
Maximum Distance (point to point) 100 m (328 )
Cable Requirements Category 5e or greater with TIA/EIA-568B crimp paern
Encoding Data Rate 2160p: Average; 250 Mbps
1080p: Average; 150 Mbps
Encoding Method VBR
End to End Latency 17-33 ms (1-2 fps)
Chassis and Environmental
Construcon Black Steel
Dimensions (H x W x D) 25 mm x 220 mm x 130.2 mm (0.98in x 8.66 in x 5.13 in)
Operang Temperature 0° to +40° C (+32° to +104° F)
Operang Humidity 20% to 90%, Non-condensing
Storage Temperature -10° to +60° C (+14° to +140° F)
Storage Humidity 20% to 90%, Non-condensing
Power and Regulatory
Power Input 12V DC 1A or 48V DC PoE (Power over Ethernet)
Power over Ethernet (PoE) Compability 802.3af Alternave A
Power Consumpon 6 was
ESD Protecon 8kV air, 4kV contact
Regulatory FCC, CE, RoHS
Other
Warranty 5 years
Diagnosc Indicators Power and Status
Included Accessories Installaon Guide, Power Supply with US, UK, EU and AU adapters, 3-pin Removable Screw
Terminal, Mounng Ears (2 ea), IR emier, IR receiver
IP Controller IPEXCB
Compable Decoder IPEX5002
Distances and picture quality may be aected by cable grade, cable quality, source and desnaon equipment, RF and electrical interference, and cable
patches.

IPEX5000 Series Quick Install Guide
17
IPEX5001-WP-W Technical Specicaons
Input/Output Connecons
Video Input One (1) HDMI (Type A Receptacle), One (1) VGA (DB-15)
LAN One (1) 8P8C port (Shielded RJ45)
Power One (1) 2 pin phoenix connector
RS232 Port One (1) 3.5mm
USB Device One (1) USB Type B Port
Audio Input (VGA) One (1) 3.5 mm TRS Receptacle
Reset One (1) Momentary Push Buon
Supported Audio, Video and Control
Video Resoluons SMPTE: 480p, 576p, 720p, 1080i, 1080p, 2160p/30 (4:4:4), 2160p/60 (4:2:0)
VESA: Resoluons up to 1920x1200
Color Depth: 24, 30, 36 bit
Video Compliance HDMI 1.4 and HDCP 1.4/2.2
Embedded Audio Up to PCM 8 channel, Dolby Digital True HD, DTS-HD Master Audio, Dolby Atmos and DTS-X
ARC (Audio Return Channel) No
HEC (HDMI Ethernet Channel) No
CEC (Consumer Electronics Control) No
Supported Baud Rates 2400, 4800, 9600, 19200, 38400, 57600, 115200
USB Compliance USB 2.0 Full Speed up to 12Mbps
Streaming Signal Characteriscs
Maximum Distance (point to point) 100 m (328 )
Cable Requirements Category 5e or greater with TIA/EIA-568B crimp paern
Encoding Data Rate 2160p: Average; 250 Mbps
1080p: Average; 150 Mbps
Encoding Method VBR
End to End Latency 17-33 ms (1-2 fps)
Chassis and Environmental
Dimensions (H x W x D) 105.6 mm x 89 mm x 43.5 mm (4.1in x 3.5 in x 1.7 in)
Operang Temperature 0° to +40° C (+32° to +104° F)
Operang Humidity 20% to 90%, Non-condensing
Storage Temperature -10° to +60° C (+14° to +140° F)
Storage Humidity 20% to 90%, Non-condensing
Power and Regulatory
Power Input 12V DC 1A or 48V DC PoE (Power over Ethernet)
Power over Ethernet (PoE) Compability 802.3af Alternave A
Power Consumpon 6 was
ESD Protecon 8kV air, 4kV contact
Regulatory FCC, CE, RoHS
Other
Warranty 5 years
Diagnosc Indicators Power and Status
Included Accessories Installaon Guide, (1) 2 pin phoenix connector, (1) 2 gang decora wall plate cover with screws,
(4) mounng screws
IP Controller IPEXCB
Compable Decoder IPEX5002
Distances and picture quality may be aected by cable grade, cable quality, source and desnaon equipment, RF and electrical interference, and cable
patches.

IPEX5000 Series Quick Install Guide
18
IPEX5001-D Technical Specicaons
Input/Output Connecons
HDMI Input One (1) HDMI Type A Receptacle
HDMI Output One (1) HDMI Type A Receptacle
LAN One (1) 8P8C port (Shielded RJ45)
Power One (1) 5.5 mm OD, 2.6 mm ID Threaded Barrel
RS232 Port One (1) 3-pin Removable Terminal Block Connector
USB Device One (1) USB Type B Port
Audio Input One (1) 3.5 mm TRS Receptacle
Audio Output One (1) 3.5 mm TRS Receptacle
IR Input One (1) 3.5 mm TRS Receptacle
IR Output One (1) 3.5 mm TRS Receptacle
Reset One (1) Momentary Push Buon
Mode One (1) Two Posion Slider Switch
DIP One (1) Four Posion DIP Switch
Supported Audio, Video and Control
Video Resoluons SMPTE: 480p, 576p, 720p, 1080i, 1080p, 2160p/30 (4:4:4), 2160p/60 (4:2:0)
VESA: Resoluons up to 1920x1200
Color Depth: 24, 30, 36 bit
Video Compliance HDMI 1.4 and HDCP 1.4/2.2
Embedded Audio Up to PCM 8 channel, Dolby Digital True HD, DTS-HD Master Audio, Dolby Atmos and DTS-X
ARC (Audio Return Channel) No
HEC (HDMI Ethernet Channel) No
CEC (Consumer Electronics Control) No
Supported Baud Rates 2400, 4800, 9600, 19200, 38400, 57600, 115200
USB Compliance USB 2.0 Full Speed up to 12Mbps
Streaming Signal Characteriscs
Maximum Distance (point to point) 100 m (328 )
Cable Requirements Category 5e or greater with TIA/EIA-568B crimp paern
Encoding Data Rate 2160p: Average; 250 Mbps
1080p: Average; 150 Mbps
Encoding Method VBR
End to End Latency 17-33 ms (1-2 fps)
Chassis and Environmental
Construcon Black Steel
Dimensions (H x W x D) 25 mm x 220 mm x 130.2 mm (0.98in x 8.66 in x 5.13 in)
Operang Temperature 0° to +40° C (+32° to +104° F)
Operang Humidity 20% to 90%, Non-condensing
Storage Temperature -10° to +60° C (+14° to +140° F)
Storage Humidity 20% to 90%, Non-condensing
Power and Regulatory
Power Input 12V DC 1A or 48V DC PoE (Power over Ethernet)
Power over Ethernet (PoE) Compability 802.3af Alternave A
Power Consumpon 6 was
ESD Protecon 8kV air, 4kV contact
Regulatory FCC, CE, RoHS
Other
Warranty 5 years
Diagnosc Indicators Power and Status
Included Accessories Installaon Guide, Power Supply with US, UK, EU and AU adapters, 3-pin Removable Screw
Terminal, Mounng Ears (2 ea), IR emier, IR receiver
IP Controller IPEXCB
Compable Decoder IPEX5002
Distances and picture quality may be aected by cable grade, cable quality, source and desnaon equipment, RF and electrical interference, and cable
patches.

IPEX5000 Series Quick Install Guide
19
IPEX5002 Technical Specicaons
Input/Output Connecons
HDMI Input One (1) HDMI Type A Receptacle
HDMI Output One (1) HDMI Type A Receptacle
LAN One (1) 8P8C port (Shielded RJ45)
Power One (1) 5.5 mm OD, 2.6 mm ID Threaded Barrel
RS232 Port One (1) 3-pin Removable Terminal Block Connector
USB Device Two (2) USB Type A Port
Audio Output One (1) 3.5 mm TRS Receptacle
IR Input One (1) 3.5 mm TRS Receptacle
IR Output One (1) 3.5 mm TRS Receptacle
Reset One (1) Momentary Push Buon
Mode One (1) Two Posion Slider Switch
DIP One (1) Four Posion DIP Switch
Supported Audio, Video and Control
Video Resoluons SMPTE: 480p, 576p, 720p, 1080i, 1080p, 2160p/30 (4:4:4)
VESA: Resoluons up to 1920x1200
Color Depth: 24, 30, 36 bit
Video Compliance HDMI 1.4/2.0 and HDCP 1.4/2.2
Embedded Audio Up to PCM 8 channel, Dolby Digital True HD, DTS-HD Master Audio and Dolby Atmos and
DTS-X
ARC (Audio Return Channel) No
HEC (HDMI Ethernet Channel) No
CEC (Consumer Electronics Control) Yes
Supported Baud Rates 2400, 4800, 9600, 19200, 38400, 57600, 115200
USB Compliance USB 2.0 Full Speed up to 12Mbps
Streaming Signal Characteriscs
Maximum Distance (point to point) 100 m (328 )
Cable Requirements Category 5e or greater with TIA/EIA-568B crimp paern
Encoded Data Rate 2160p: Average; 250 Mbps
1080p: Average; 150 Mbps
Encoded Method VBR
End to End Latency 17-33 ms (1-2 fps)
Maximum Video Wall Size 16x16
Chassis and Environmental
Construcon Black Steel
Dimensions (H x W x D) 25 mm x 220 mm x 130.2 mm (0.98in x 8.66 in x 5.13 in)
Operang Temperature 0° to +40° C (+32° to +104° F)
Operang Humidity 20% to 90%, Non-condensing
Storage Temperature -10° to +60° C (+14° to +140° F)
Storage Humidity 20% to 90%, Non-condensing
Power and Regulatory
Power Input 12V DC 1A or 48V DC PoE (Power over Ethernet)
Power over Ethernet (PoE) Compability 802.3af Alternave B
Power Consumpon 6 was
ESD Protecon 8kV air, 4kV contact
Regulatory FCC, CE, RoHS
Other
Warranty 5 years
Diagnosc Indicators Power and Status
Included Accessories Installaon Guide, Power Supply, 3-pin Removable Screw Terminal, Mounng Ears (2 ea), IR
emier, IR receiver
IP Controller IPEXCB
Compable Encoder IPEX5001
Distances and picture quality may be aected by cable grade, cable quality, source and desnaon equipment, RF and electrical interference, and cable
patches.

Thank you for your purchase.
For Technical Support please call our toll free number at
800-530-8998 or email us at [e-mail]
www.libav.com
Digitalinx is a brand of:
11675 Ridgeline Drive
Colorado Springs, Colorado
80921 USA
Phone: [phone]
Fax: [phone]
Toll-Free: 800-530-8998