Digitalview Hx-4096 User manual

Specifications subject to change without notice

DVI, DISPLAY PORT, HDMI, VIDEO INTERFACE CONTROLLER

FOR TFT PANEL

Model: HX-4096

Part number : 41755012X-3 or up

INSTRUCTIONS

CONTENTS

Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer

3. System design – Diagram of a suggested system

5. Assembly notes – Important information about system elements

7. Connection & Operation – How to use the controller

13. Connectors, pinouts & jumpers – Essential connection information

30. Controller dimensions

31. Application notes

33. Troubleshooting

34. Specifications

36. Appendix I – Signal support modes table

40. Appendix II – Network connection

43. Appendix III – RS-232 control protocols and command set

53. Appendix IV - Mapping definition

55. Appendix V – DV remote control unit work for HX-4096

56. Appendix VI - PIP mix table

57. Appendix VII – Functions list on browser page

60. Warranty, Caution & Limitation of Liability, Trademarks

61. Contact details

62. Revision History

It is essential that these instructions are read and understood before connecting or

powering up this controller.

Specifications subject to change without notice

Introduction

Designed for LCD monitor and other flat panel display applications, the HX-4096 is a feature rich interface controller for :

 TFT (active matrix) LCD panels of 4096x2160 resolutions in 60Hz with V-by-One, eDP or LVDS interface.

 Support true 10 bits panel

 Support HDMI, DVI and Display Port input.

HOW TO PROCEED

 Ensure you have all parts & that they are correct, refer to:

 Connection diagram

 Connector reference (in following section)

 Assembly notes

 Check controller switch & jumper settings (errors may damage the panel)

 Prepare the signal sources

 Connect the parts

 Understand the operation & functions

IMPORTANT USAGE NOTE

This equipment is for use by developers and integrators, the manufacturer accepts no liability for damage or injury caused by

the use of this product. It is the responsibility of the developer, integrators or other user of this product to:

 Ensure that all necessary and appropriate safety measures are taken.

 Obtain suitable regulatory approvals as may be required.

 Check power settings to all component parts before connection.

DISCLAIMER

There is no implied or expressed warranty regarding this material.

Controller Solution Generator

Full web resource matching controllers & panels with connection diagrams for download.

See

at

:

http://www.digitalview.com/csg

Specifications subject to change without notice

SYSTEM DESIGN

A typical LCD based display system utilizing this controller is likely to comprise the following:

Specifications subject to change without notice

ASSEMBLY NOTES

This controller is designed for monitor and custom display projects using 4096x2160 resolution with V-by-One interface, eDP interface

or LVDS TFT panels. The following provides some guidelines for installation and preparation of a finished display solution.

Preparation: Before proceeding it is important to familiarize yourself with the parts making up the system and the various connectors,

mounting holes and general layout of the controller. As much as possible connectors have been labeled. Guides to connectors and

mounting holes are shown in the following relevant sections.

1. LCD Panel: This controller is designed for typical V-by-One (8 lanes), eDP (HBR/HBR2) and LVDS interfaced panels with panel

voltage 3.3V(4A), 5V(4A), 10V(4A), 12V(4A) or 18V(3A), External for 10V, 12V and 18V interface. Due to the variation between

manufacturers of panels signal timing and other panel characteristics, factory setup and confirmation should be obtained before

connecting to a panel. (NOTE: Check panel power jumper settings before connection)

2. LCD Controller: Handle the controller with care as static charge may damage electronic components. Make sure correct jumper

to match the target LCD panel.

3. Panel cable: In order to provide a clean signal it is recommended that all panel cables (V-by-One signal, eDP and LVDS) supplied

by Digital View. Care should be taken when placing the cables to avoid signal interference.

4. Inverter/Backlight driver: This will be required for the backlight of an LCD, some LCD panels have an inverter/backlight driver

built in. As LCD panels may have 1 or more backlight tubes and the power requirements for different panel backlights may vary it

is important to match the inverter/backlight driver in order to obtain optimum performance. See Application notes page 31 for

more information on connection.

5. Inverter/backlight cables: Different inverter/backlight models require different cables and different pin assignment. Make sure

correct cable pin out to match the inverter/backlight. Using wrong cable pin out may damage the inverter/backlight.

6. Function Controls: The following section discusses the controls required and the section on connectors provides the detail. The

controls are minimal: On/Off, Backlight Brightness (depends on inverter), OSD (5 momentary buttons) analog VR type or (8

momentary buttons) digital type.

7. Function controls cable: The cables to the function switches should be of suitable quality and length so that impedance does

not affect performance. Generally lengths up to 1 meter (3 feet) should be acceptable.

8. Optional LED: The pin direction of the LED should be corrected for right color indication. Red color stands for standby. Green

colors stands for signal on. The status LED is an optional part only, can be unconnected.

9. Optional IR sensor: It is an optional part only, can be unconnected if not using IR remote control.

10. RS-232 control interface : Serial control via this interface port.

11. External panel power output : User for specific panel model.

12. Panel control signal : Use for specific panel model.

13. SPDIF Audio output : This port support SPDIF audio output from the HDMI / Display Port audio source inputted.

14. Ambient light sensor connection : 3 ways connector provides interface for ambient light sensor connection by using Kit 70220-3.

15. Backlight status input : 2 ways connector provides interface for connection with the specific panel type which support the panel

with backlight status monitoring function.

16. On board LED backlight driver : The on board LED driver supports 4 LED strings max 50V total LED backlight via J10

connector.

17. DVI-I input cable : Plug the DVI cable to the connector P1 on the controller board.

18. HDMI input : Plug the HDMI cable to the connector P2(HDMI 1.4) / P3(HDMI 1.4) / P4(HDMI 2.0) on the controller board. This

port is not supported when CN5/CN16 are connected.

19. Alternate HDMI input : This port gives alternate HDMI input support.

20. Alternate DVI-I input : This port gives alternate DVI-I input support.

21. Control over network connection : This is a network device that allow to control RS-232 enable devices over a TCP/IP based

Ethernet and the Internet using a web browser. Please refer to Appendix V in details.

22. Reserved for Audio adaptor board P/N 416940020-3: The audio add-on board gives the audio input and output signal

connection. It is an optional and reserved part only, can be unconnected if not using audio. It requires an audio cable P/N

426451800-3 to connect HX-4096 (CN14) to the Audio Add-on Board (CN2).

CAUTION : The Audio Add-on Board P/N 416940020-3 can only operate with 12VDC power input environment.

Specifications subject to change without notice

23. Reserved for Audio extend cable : The audio extend cable P/N 426009700-3 designs for connection between audio add on

board P/N 416940020-3 and the controller. It is an optional and reserved part only, can be unconnected if not using audio.

24. Additional panel power input : Provide additional (+10V/+12V/+18V) panel power input for driving high power consumption

panels.

25. Power Input: 12V/24VDC is required, this should be a regulated supply. It allows 12V (5A) or 24V (5A) via PP5 power input

connector. The power rating is depending on the panel and inverter used. Although the controller provides power regulation for

the LCD power this does not relate to the power supplied to the backlight inverter.

If an unregulated power supply is provided to an inverter any fluctuations in power may affect operation, performance and lifetime

of the inverter and or backlight tubes.

26. External panel power input : Allow to supply external power to the panel separately for max 3.3V (7A) or 5V (7A) or 10V (5A) or

12V (5A) or 18V (3.5A) via PP4 power input connector. Corresponding jumper setting of JA3, JA5 & JA6 are required for each

panel power input by referring to page 16.

 Power output: Note the controller has an overall 3Amp current limit and the current available from the auxiliary power output will

be dependent on the power input and other system requirements.

 Power Safety: Note that although only 12V / 24VDC is required as ‘power-in’ a backlight inverter for panel backlighting produces

significantly higher voltages (the inverter does not connect to the ground plane). We strongly advise appropriate insulation for all

circuitry.

 EMI: Shielding will be required for passing certain regulatory emissions tests. Also the choice of external Controller to PC signal

cable can affect the result.

 Ground: The various PCB mounting holes are connected to the ground plane.

 Servicing: The board is not user serviceable or repairable. Warranty does not cover user error in connecting up to the controller

and is invalidated by unauthorized modification or repairs.

 Controller Mounting: It is recommended that a clearance of at least 10mm is provided above and 5mm below the controller

when mounted. Additionally consideration should be given to:

 Electrical insulation.

 Grounding.

 EMI shielding.

 Cable management. Note: It is important to keep panel signal cables apart from the inverter & backlight cables to prevent

signal interference.

 Heat & Ventilation: Heat generated from other sources, for example the backlight of a very high brightness panel may

generate significant heat which could adversely affect the controller.

 Other issues that may affect safety or performance.

 PC Graphics Output: A few guidelines:

 Signal quality is very important, if there is noise or instability in the PC graphics output this may result in visible noise on the

display.

 Refer to graphics modes table in specifications section for supported modes.

 Non-interlaced & interlaced video input is acceptable.

IMPORTANT: Please read the Application Notes section for more information.

Specifications subject to change without notice

CONNECTION & OPERATION

CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage.

CONNECTION

Connection and usage is quite straight forward (it is useful to have the relevant connection diagram available at this time):

1. LCD panel & Inverter: Connect the inverter/Backlight driver (if it is not built-in the panel) to the inverter/backlight connector of the

LCD panel.

2. V-by-One interface panels: The controller board supports V-by-One interface 4K panel. Plug the cable to J7 for driving 4K 60Hz

panel. And make sure the matching panel timings and correct jumper settings (JB13 & JB14) by referring to the panel

support table and jumper settings table in page 13-16.

3. eDP interface panels: The controller board supports eDP(1.1) or eDP(1.2) interface 4K panel. For eDP(1.1) panel, plug the cable

to J7. For eDP(1.2) panel, plug the cable to J6. And make sure the matching panel timings and correct jumper settings (JB13

& JB14) by referring to the panel support table and jumper settings table in page 13-16.

4. LVDS interface panels: The controller board supports LVDS interface 4K panel. Plug the cable to J2/J3/J4 for driving 4K 60Hz

panel. And make sure the matching panel timings and correct jumper settings (JB13 & JB14) by referring to the panel

support table and jumper settings table in page 13-16.

5. Inverter/Backlight driver: Plug the inverter/backlight cable to CNB1 and CNA1 (if necessary). Plug another end to the connector

on the inverter/backlight of panel side.

6. Function switch & Controller: Plug the OSD switch mount cable to CNC1 on the controller board and another to the OSD switch

mount.

7. LED & Controller: Plug in a 3-way with dual color LED to connector LED1 on the controller board.

8. IR & Controller: Plug in a 3-way with IR sensor to connector IR1 on the controller board.

9. Jumpers & Inverter & Panel voltage: Particularly pay attention to the settings of JA3, JA5, JA6, JB2 and JB3. JB2 & JB3 are

used for inverter control (read inverter specification and information on the jumper table to define the correct settings). JA3 &

JA5 & JA6 is used for panel voltage input (read panel specification and information on the jumper table to define the correct

settings).

10. Input signal cable & Controller: Plug the corresponding signal input to the connector on the controller board.

11. Power supply & Controller: Plug the DC 12V/24V power in to the connector PP2 or PP5. You can consider to use

DigitalView mating power cable P/N 426013710-3, 1000mm for PP5 connection.

12. External panel power input : Plug power cable : P/N 426013710-3 for external panel power input (3.3 (max 7A) / 5V (max 7A) /

10V (max. 5A) / 12V (max 5A) / 18V (max3.5)) for PP4 connection.

13. Power on: Switch on the controller board and panel by using the OSD switch mount.

General:

 If you are using supplied cables & accessories, ensure they are correct for the model of panel and controller.

 If you are making your own cables & connectors refer carefully to both the panel & inverter specifications and the section in this

manual, “Connectors, Pinouts & Jumpers” to ensure the correct pin to pin wiring.

PC SETTINGS

The controller has been designed to take a very wide range of input signals however to optimize the PC’s graphics performance we

recommend choosing 60Hz vertical refresh rate – this will not cause screen flicker.

OPERATION

Once the system has been connected and switched on there are a number of functions available to adjust the display image as

summarized in the following sections. The settings chosen will be saved for each mode independently.

Specifications subject to change without notice

LCD DISPLAY SYSTEM SETTINGS

NOTE: By way of explanation the following refers to a set of sample buttons that may be obtained as an option. In addition to

power on/off and connection for backlight brightness the controller provides an On Screen Display of certain functions which are

controlled by 5 momentary type buttons (analog VR type) or 8 momentary type buttons (digital type):

Controls Analog VR type Digital type

On/Off – turns controller board power on VR toggle switch On/Off button

Brightness – controls backlight brightness Rotary VR Brightness +/- buttons

Menu

 Turns OSD menu On or Off (it will auto time off)

Menu button Menu button

Select up

 Moves the selector to the previous level function

(up)

SEL UP SEL UP

Select down

 Moves the selector to the next level function

(down)



Confirm the OSD selection

SEL DN SEL DN

+

 Increase the OSD parameter values

 Moves the selector to next function (forward)

+ +

-

 Decrease the OSD parameter values

 Moves the selector to previous function

(backward)

- -

* Sequence of Input source selection (Press "+" Button to change source, Press "SEL DN" to confirm)

ON/Off/Brightness

SEL UP

SEL DN

+

-

Menu

Analog VR type

Digital type

12V / 24VDC power input :

Digital 10K Type OSD switch

mount uses

P/N 416100520-3 or up

12V / 24VDC power input :

Analog 10K VR Type OSD

switch mount uses

P/N 410680550-3 or up

Specifications subject to change without notice

OSD functions

Display Mode:

[Default]

Display Function:

1P: Disp Rotate : 0 [Default]

90

180

270

2P LR: Input Swap

2P TB: Input Swap

2P PIP: PIP Position : Top-left

Top-right

Bottom-left

Bottom-right [Default]

PIP Transparency : [0 - 10] [Default 0]

PIP Size : [0 - 10] [Default 10]

Input Swap

Picture:

Backlight [0-100] [Default 100]

Brightness [0-100] [Default 50]

Contrast [0-100] [Default 50]

Sharpness [0-4] [Default 2]

VGA Setup:

Auto Adjust

H Position [0-100] [Default 50]

V Position [0-100] [Default 50]

Clock [0-100] [Default 50]

Phase [0-100] [Default 0]

Color Gain : Set

Reset

Color:

Gamma : 1.8

2.0

2.2 [Default]

2.4

Temperature: 9300

7500

6500 [Default]

5800

3200

sRGB

User : R [0-255]

G [0-255]

B [0-255]

Color Effect: Standard [Default]

Game

Movie

Photo

Vivid

Specifications subject to change without notice

User: R:

Hue [0-100]

Sat [0-100]

Y:

Hue [0-100]

Sat [0-100]

G:

Hue [0-100]

Sat [0-100]

C:

Hue [0-100]

Sat [0-100]

B:

Hue [0-100]

Sat [0-100]

M:

Hue [0-100]

Sat [0-100]

Hue: [0-100] [Default 50]

Saturation [0-100] [Default 50]

Advanced:

Aspect Ratio: Full [Default]

16:9

4:3

5:4

1:1

Over Scan: ON [Default]

OFF

Over Drive: ONOFF: ON

OFF [Default]

OD Gain [0-100] [Default 50]

Communication: RS-232 [Default]

Network

Auto Source Seek: OFF

ON [Default]

Hot Key: Hot Key 1 (< | >) : Input

Backlight

Brightness

Contrast

Sharpness

Hue

Saturation

Aspect Ratio

Display Mode

Input Swap

PIP Size

Auto Adjust

Volume

No Function [Default]

Hot Key: Hot Key 1 (Up | Dn) : Input

Backlight

Brightness

Contrast

Sharpness

Hue

Saturation

Aspect Ratio

Display Mode

Input Swap

PIP Size

Auto Adjust

Volume

No Function [Default]

Specifications subject to change without notice

Power Save: OFF

ON [Default]

Default Power: OFF

ON [Default]

Input:

(For all display modes: 1P/ 2R LR / 2P TB / 2P PIP / 4P)

A0 : VGA

D0 : DP

D1 : HDMI

D2 : HDMI

D3 : HDMI

D4 : DVI

Audio:

Volume [0-100] [Default 50]

Mute: ON

OFF [Default]

Audio Source (1P) : Analog [Default]

Digital (region 1)

Audio Source (2P LR) : Analog [Default]

Digital (region 1) - Left

Digital (region 2) - Right

Audio Source (2P TB) : Analog [Default]

Digital (region 1) - Top

Digital (region 2) - Bottom

Audio Source (2P PIP) : Analog [Default]

Digital (region 1) - Main

Digital (region 2) - Sub

Audio Source (4P) : Analog [Default]

Digital (region 1) - Upper left

Digital (region 2) - Lower left

Digital (region 3) - Upper right

Digital (region 4) - Lower right

Other:

Reset

Menu Time [On, 11-60] [Default 11]

OSD H Position [0-100] [Default 50]

OSD V Position [0-100] [Default 50]

Language

Transparency [0-255] [Default 0]

Rotate: 0 [Default 0]

90

270

Border Width: [0-10] [Default 0]

Border Color: R [Default]

G

B

W

Specifications subject to change without notice

Information:

Factory:

Backlight Setup: Invert : OFF [Default]

ON

D/A / PWM : PWM [Default]

D/A

Frequency : [100Hz - 440Hz] [Default 160Hz]

Min. Level : [0% - 50%] [Default 5%]

VBy1 Setup : Pin 15 : Low [Default]

High

Pin 16 : Low [Default]

High

Pin 17 : Low [Default]

High

Pin 18 : Low [Default]

High

Pin 19 : Low [Default]

High

Pin 20 : Low [Default]

High

Pin 21 : Low [Default]

High

Pin 22 : Low [Default]

High

Pin 23 : Low [Default]

High

Pin 24 : Low [Default]

High

EDID Setup : Reset

Specifications subject to change without notice

CONNECTORS, PINOUTS & JUMPERS

The various connectors are:

Summary: Connectors

Ref Purpose Description

CN1 Reserved for second RS-232 serial

control

JST 6-way, B6B-XH-A (Matching type : XHP-6)

CN2 On board internal connector for DVI JST BM29B-SRDS (Mating type : SHDR-20V-S-B)

(Matching extend cable P/N: 426302900-3)

CN3 Reserved for external temperature

sensor

JST 3-way, B3B-XH-A (Matching type : XHP-3)

CN5 On board internal connector for HDMI JST BM20B-SRDS (Matching type : SHDR-20V-S-B)

CN6 Reserved for light sensor DF13 2 ways (Matching type : DF13-2S-1.25C)

CN7 Audio board connector Dual pin header 5x2, 0.1" pitch right angle

(Matching audio add-on board P/N 416940020-3)

CN8 RS-232 serial control JST 6-way, B6B-XH-A (Matching type : XHP-6)

CN9 Ambient light sensor connector JST 3-way, B3B-PH-K (Matching type : PHR-3)

CN10 Reserved for Fan & backlight power

monitoring connector

Hirose DF13-9P-1.25 DSA (Mating type : DF13-9S-1.25C)

CN11 SPDIF Audio output JST B2B-ZR (Matching type : ZHR-2)

(Matching extend cable P/N 426007400-3)

CN12 Reserved for engineering use Reserved

CN13 Audio line in JST B4B-ZR (Matching type : ZHR-4)

CN14 Audio line out JST B4B-ZR (Matching type : ZHR-4)

(Use audio cable P/N 426451800-3 to connect with audio add-on bard

P/N 416940020-3)

CN15 Power connector for IE-2000 Yeonho SMH200-04 (Matching type : SMH200-04)

(Matching extend cable P/N:426307100-3)

CN16 On board internal connector for HDMI JST BM20B-SRDS (Matching type : SHDR-20V-S-B)

CN19 Additional panel power output JST B10B-PH-K (Matching type : PHR-10)

CNA1 Auxiliary power output JST 4-way, B4B-XH-A (Matching type : XHP-4)

(Matching cable P/N 426040200-3)

CNB1 Backlight inverter JST 5-way, B5B-XH-A (Matching type : XHP-5)

(Matching cable P/N 426058300-3)

CNB2 Backlight status input connector JST 2 way, B2B-XH-A (Matching type : XHP-2)

CNC1 OSD control Hirose DF13A-12P-1.25H (Mating type : DF13-12S-1.25C)

(Matching OSD switch mount cable P/N 426122200-3 (150mm) or

426122210-3 (250mm)

CP2 Reserved Reserved

Specifications subject to change without notice

IR1 Infra-red sensor connector JST 3-way, B3B-XH-A (Matching type : XHP-3)

J1 Ethernet RJ-45 connector

J2 LVDS 3 JAE FI-RE51S-HF (Matching type : FI-RE51HL)

J3 LVDS 1 JAE FI-RE51S-HF (Matching type : FI-RE51HL)

J4 LVDS 2 JAE FI-RE41S-HF (Matching type : FI-RE41HL)

J5 Panel power output JS-1147A-08 Top 1.25mm (Matching type : JS-1146-08)

J6 eDP (1.2) connector I-PEX 20455-030E-12 (Matching type : I-PEX 20454-030T)

J7 V-by-One panel signal output JAE FI-RE51S-HF (Matching type : FI-RE51HL)

J10 On board LED backlight driver

connector

Molex 53261-1000 (Matching type : Molex 51021-1000)

LED1 Power LED connector 3-pins header

P1 DVI-I -- D4 / VGA -- A0 DVI-I connector

P2 HDMI (1.4) -- D3 HDMI connector

P3 HDMI (1.4) -- D2 HDMI connector

P4 HDMI (2.0) -- D1 HDMI connector

P5 Display Port (1.2) -- D0 Display Port connector

PP2 Power input (alternative) DC power Molex 2 pin 0.156” pitch

PP4 External panel power input Molex 43045-0400 compatible

(Matching connector type : Molex 43025-0400 compatible)

(Matching power cable : P/N 426013710-3)

PP5 12V/24VDC input power Molex 43045-0400 compatible

(Matching connector type : Molex 43025-0400 compatible)

(Matching power cable : P/N 426013710-3)

S1 Reset button (for Ethernet function) Tact switch button

S2 Reserved Tact switch button

S4 Config Menu button (for Ethernet

function)

Tact switch button

SW3 Panel selection 8-way DIP Switch

SW4 Function selection 6-way DIP Switch

Specifications subject to change without notice

Summary: Jumpers setting

Ref

Purpose Note

JA3 Panel power voltage select

CAUTION: Incorrect setting can damage

panel

See panel voltage setting table 1

JA5 Panel power voltage select

CAUTION: Incorrect setting will cause panel

damage

See panel voltage setting table 1

JA6 Panel power voltage select

CAUTION: Incorrect setting will cause panel

damage

See panel voltage setting table 1

JA15 Panel power output control via J7 (pin 1-8)

and J6 (pin 5-9)

1-3, 2-4 = Enable panel power (3.3/5V) output on J7 and

J6

3-5, 4-6 = Enable panel power (10/12/18/24V) output on

J7 and J6

Open = Disable panel power output on J7 and J6

JB1 Backlight brightness voltage range 1-2 = 5V max

2-3 = 3.3V max

JB2 Backlight inverter on/off control – signal level 2-3 = On/Off control signal ‘High’ = +5V

1-2 = On/Off control signal ‘High’ = +3.3V

Open = On/Off control signal ‘High’ = Open collector

CAUTION: Incorrect setting can damage inverter.

JB3 Backlight inverter on/off control – polarity 1-2 = control signal ‘high’ = Backlight ON

2-3 = control signal ‘low’ = Backlight ON

JB4 Reserved for LVDS (J3) GPIO pins voltage

selection

1-2 = 3.3V

2-3 = 5V

JB5 Backlight control type selection 1-2 = VR/Digital switch mount control

3-4 = Analog backlight brightness - voltage range 0~5V

5-6 = PWM (Pulse Width Modulation) brightness

JB7 Backlight control voltage on CNB1 pin 4

(Function when JB5 sets 1-2 closed)

Open = For OSD switch mount control (Default)

1-2 = 0V

2-3 = 3.3V / 5V controlled by JB1

JB8 LED backlight current selection

150mA

120mA

110mA

100mA

90mA

JB9 On board LED backlight driver function Open = Disable

Closed = Enable

JB13 V-by-One / eDP selection on J7 1-2 = V-by-One

2-3 = eDP (1.1)

JB14 V-by-One / eDP selection on J7 1-2 = V-by-One

2-3 = eDP (1.1)

JC1 and

JC2

Open = Low / GND / NC*

Close = High

* The setting of NC (No connection) is subject to the NC's state

defined in panel specification.

JP1 Factory use Default Open

JP2 V-by-One power output configuration 1-2 = All pin 44 ~ pin 51 on J7 have power output

Open = Only the upper four pins have power output

(Refer to power output enabled/disabled on JA15. But

not applicable if JA15 is set to OPEN)

JP6 Input power control Short = External switch control and fix the board ON

Open = Switch mount control

Specifications subject to change without notice

Table 1 : Panel voltage setting table :

Input voltage via

PP2/PP5 Panel Voltage JA3 JA5

JA6 Jumper on board

12VDC

3.3V 3V3 closed

1-3 & 2-4 1-3 & 2-4

5V 5V closed 1-3 & 2-4 1-3 & 2-4

12V OPEN 1-3 & 2-4 5-7 & 6-8

CAUTION: Incorrect setting can damage panel & controller

Input voltage via

PP2/PP5 Panel Voltage JA3

JA5 JA6 Jumper on board

24VDC**

3.3V 3V3 closed

1-3 & 2-4 1-3 & 2-4

5V 5V closed 1-3 & 2-4 1-3 & 2-4

10V 10V closed

1-3 & 2-4 3-5 & 4-6

12V 12V closed

1-3 & 2-4 3-5 & 4-6

18V

18V closed

1-3 & 2-4 3-5 & 4-6

CAUTION: Incorrect setting can damage panel & controller

** Ensure that the backlight inverter supports 24V operation prior to connecting a 24VDC input.

Because CNA1 pin 1 and CNB1 pin 2 will output 24VDC if input 24VDC via PP5 or PP2.

Specifications subject to change without notice

Input voltage via

PP4

Input voltage via

PP2 / PP5 Panel Voltage JA3

JA5 JA6 Jumper on board

3.3 / 5 / 10 /12 /

18VDC* 12V / 24VDC

3.3V OPEN 3-5 & 4-6 1-3 & 2-4

5V OPEN 3-5 & 4-6 1-3 & 2-4

10V OPEN 3-5 & 4-6 3-5 & 4-6

12V OPEN 3-5 & 4-6 3-5 & 4-6

18V

OPEN 3-5 & 4-6 3-5 & 4-6

* Maximum current for 3.3V, 5V = 7A, Maximum current for 10V, 12V = 5A, Maximum current for 18V = 3.5A

JA3, JA5 & JA6 location on board : (Please pay attention to the jumper settings on JA3, JA5

&

JA6

which are red in color)

JA3,

JA6

& JA5

Specifications subject to change without notice

Table 2 : DIP Switch selection – SW3

Pos #1 Pos #2 Pos #3 Pos.#4 Description Panel resolution

For 4K UHD panels

OFF OFF OFF OFF IE-2000 (120Hz FRC) 3840 x 2160

OFF OFF OFF OFF V-By-One panel 3840 x 2160

ON OFF OFF OFF Reserved 3840 x 2160

OFF ON OFF OFF Reserved 3840 x 2160

ON ON OFF OFF Reserved 3840 x 2160

OFF OFF ON OFF eDP1.2 panel 3840 x 2160

OFF OFF OFF ON Reserved 3840 x 2160

For WUXGA panels

OFF OFF OFF OFF LVDS panel 1920 x 1200

ON OFF OFF OFF LVDS panel 1920 x 1080

Remark : The above panel timings are generated based on the panel specification. Some of the panel timings

settings may not exactly to match the panel model we specified in this table.

Pos #5 Pos #6 Pos #7 Description

OFF OFF OFF WUXGA (1920 x 1200 / 1080)

ON OFF OFF Reserved

OFF ON OFF Reserved

ON ON OFF Reserved

OFF OFF ON Reserved

ON OFF ON Reserved

OFF ON ON 4K UHD (3840 x 2160)

ON ON ON Others

Pos. #8 Reserved

Table 3 : DIP switch selection – SW4

Pos # Function Description

1 LVDS data mapping OFF: VESA

ON: JEIDA

2 and 3 Panel display division

Pos#3 Pos#2

OFF OFF 1 division (Non-division)

OFF ON 2 division

ON OFF 4 division

ON ON 8 division

4 Output display bit mode OFF: 10-bit

ON: 8-bit

5 Reserved Reserved

6

V-by-One settings

OFF: Determine by JC1 and JC2

ON: Determine by OSD menu

Note: For setting definition, please refer to V-by-One's pin#15 to pin#24 of panel specification.

Specifications subject to change without notice

Panel support

4K 60Hz panel

Manufacturer Panel model Panel resolution

AU Optronics M270DAN02.3 2560 x 1440

AU Optronics M320QAN01.0 3840 x 2160

AU Optronics P550QVN01.0 3840 x 2160

AU Optronics P750QVN01.1

3840 x 2160

BOE MV238QUM-N20 3840 x 2160

Innolux M238DCJ-E50 3840 x 2160

Innolux M280DGJ-L30* 3840 x 2160

Innolux M315DJJ-K30 3840 x 2160

Innolux

N173DSE-G31 3840 x 2160

Innolux

S400DJ1-KS5 3840 x 2160

Innolux

V400DK2-KS5 3840 x 2160

Innolux

V420DK1-KS1 3840 x 2160

Innolux V500DK1-LS1 3840 x 2160

Innolux V500DK2-KS1 3840 x 2160

LG LC430EQE-FHM1 3840 x 2160

LG LC490EQE-FHM2 3840 x 2160

LG LC550EQE-FHM1 3840 x 2160

LG

LD550EGE-FHM1 3840 x 2160

LG

LD750DGN-FKH1 3840 x 2160

LG

LM238WR1-SLA1 3840 x 2160

LG

LM238WR2-SLC1 3840 x 2160

LG

LM270WR2-SPA1 3840 x 2160

LG LM300WQ6-SLA1 2560 x 1600

LG LM315WR1-SSA1 3840 x 2160

Samsung LTM236FL01 3840 x 2160

Samsung LTM270FL01* 3840 x 2160

4K 120Hz panel

Manufacturer Panel model Panel resolution

AU Optronics P650QVN01.0*

3840 x 2160

AU Optronics

P750QVN01.0 3840 x 2160

Innolux V400DK2-KS5 3840 x 2160

Innolux V500DK1-KS2 3840 x 2160

Innolux

V500DK1-KS5 3840 x 2160

Innolux

V850DK1-KD1 3840 x 2160

LG

LC550EQD-FGF2 3840 x 2160

LG

LD750EQF-FJM1 3840 x 2160

LG

LD840EQD-SEM1 3840 x 2160

LG

LD860EQD-FJM1 3840 x 2160

LG

LD980DQD-FGM1 3840 x 2160

LG

ND840EQD-SADX1 3840 x 2160

Remark :

1. The panel model marked with (*) means the model has been verified by DigitalView.

2. The panel model without marked with (*) means the model has not been tested and verified but have a suggested connection

diagram provide.

3. For the 4K 120Hz panel connection, IE-2000 is required.

Specifications subject to change without notice

CN1 – RS-232 serial control (2nd): JST B6B-XH-A (Matching type : XHP-6)

PIN SYMBOL DESCRIPTION

1 NC No connection

2 NC No connection

3 VCC +5V

4 TXD RS-232 Tx data

5 GND Ground

6 RXD RS-232 Rx data

CN2 – Alternate DVI connector: JST BM20B-SRDS (Matching type : SHDR-20V-S-B)

PIN SYMBOL DESCRIPTION

1 GND Digital Ground

2 GND Digital Ground

3 RXC TMDS Clock+

4 /RXC TMDS Clock-

5 RX0 TMDS Data 0+

6 /RX0 TMDS Data 0-

7 RX1 TMDS Data 1+

8 /RX1 TMDS Data 1-

9 RX2 TMDS Data 2+

10 /RX2 TMDS Data 2-

11 GND Ground (+5, Analog H/V Sync)

12 GND Digital Ground

13 EXT _SCL Reserved

14 EXT_SDA Reserved

15 DDC_5V +5V power supply for DDC (optional)

16 HPD Hot plug detect

17 DDC_CLK DDC Clock

18 DDC_DAT DDC Data

19 NC No connection

20 VCC +5V

CN3 – Temperature sensor connector : JST B3B-XH-A (Matching type : XHP-3)

PIN SYMBOL DESCRIPTION

1 GND Ground

2 VDD +3.3V

3 EX_TMP_SENSOR Temperature sensor input

CN5 - Alternate HDMI connector : JST BM20B-SRDS (Matching type : SHDR-20V-S-B)

PIN SYMBOL DESCRIPTION

1 GND Ground

2 GND Ground

3 RXC+ TMDS Data C+

4 RXC- TMDS Data C-

5 RX0+ TMDS Data 0+

6 RX0- TMDS Data 0-

7 RX1+ TMDS Data 1+

8 RX1- TMDS Data 1-

9 RX2+ TMDS Data 2+

10 RX2- TMDS Data 2-

11 GND Ground

12 GND Ground

13 EXT_SCL Reserved

14 EXT_SDA Reserved

15 DDC_5V +5V power supply for DDC (optional)

16 HPD Hot plug detection

17 DDC_SCL DDC serial clock

18 DDC_SDA DDC Data

19 NC No connection

20 VCC +5V

CN6 – Light sensor connector : DF13 2-ways (Matching type : DF13-2S-1.25C)

PIN SYMBOL DESCRIPTION

1 SENSOR Light sensor input

2 VDD +3.3V

digitalview HX-4096 User manual

Popular Controllers manuals by other brands