Digitus DN-95623 User manual

Metering Module of
Basic local monitored PDU
Manual
DN-95623

2
Safety and Grounding:
Read the following information before installing or operating your DIGITUS Power
Distribution Unit:
This PDU is intended for indoor use only.
This PDU must not be must not be operated one behind the other!
Operation only in dry and closed rooms.
This PDU may not be operated covered. Always ensure free accessibility.
The maximum power stated on the rating plate must not be exceeded.
Plug this PDU into a three-wire, grounded power outlet only.
The power outlet must be connected to appropriate branch circuit/ mains
protection (fuse or circuit breaker). Connection to any other type of power outlet
may result in a shock hazard.
Use only the supplied brackets of mounting.
Check that the power cord, plug, and socket are in good condition.
Voltage free only when the power plug is unplugged.
Disconnect the PUD from the power outlet before you install or connect
equipment to reduce the risk of electric shock when you connot verify grounding.
Reconnect the PDU to the power outlet only after you make all connections.
Operation under unfavorable environmental conditions must be avoided.
(Humidity over 80% relative, wet, ambient temperatures above 50 ° C, solvents,
flammable gases, dust, vapors).
If external damage to this PDU is detected, do not operate this PDU.
Take this PDU immediately out of service if external damage is detected.
Do not pour liquids over the power strip. There is a high risk of fire or
life-threatening electric shock.
When opening the power strip, live parts can be exposed.
There is a risk of electric shock. The power strip may only be opened by a
specialist. When opening the power strip, live parts can be exposed.
There is a risk of electric shock. The power strip may only be opened by a
specialist.

3
I、Overview
Basic Metered PDU is a data center power distribution device with local monitoring
function. It can accurately monitor voltage, current, power and electrical energy with
an accuracy of ±1%, providing customers with safe and stable power distribution
services.
II、Hardware Introduction
1．Product sketch
Basic Metered PDU is equipped with a hot-swappable monitoring module,
which can be replaced without power interruption of the devices when necessary.
2．Interactive display
2.1 Single phase two way monitoring module (AC)
Press the "BUTTON" key to turn the pages, the first to sixth screens will display the
current (00.00A), voltage (225.5V), active power (00.00kW), and electrical energy
(00007.7kWh) of L, C1 circuit and C2 circuit in sequence, and the seventh screen
displays version number (VEr1.5.9), as shown below.
1
2
3
1. Screen: LCD screen
2. RUN: Run indicator
(flashes at intervals of 1
second during normal operation)
3. BUTTON: Button key
(switch display content)
4. RESET: Restart the module
4

4
III
、
Technical Specification
Input
Single
phase
Rated voltage
100-240VAC 50~60Hz
Maximum total load
current
16A/ 32A
Three-
phase
Rated voltage
200-400VAC 50~60Hz
Maximum total load
current
3×16A, 3×32A
Direct
current
Rated voltage
240VDC/ 336VDC
Maximum total load
current
40A/ 60A
Overload protection
Circuit breaker (optional)
Input current detection and
display
Detection accuracy: ±1%;
Display accuracy: 0.01A
Display mode
：
liquid crystal
display;
Display direction:
vertical/horizontal;
Input voltage detection and
display
Detection accuracy: ±1%;
Display accuracy: 0.1V
Display mode: liquid crystal
display; Display direction:
vertical/horizontal;
Output
Single
phase
Rated voltage
100-240VAC 50~60Hz
Maximum total load
current
16A/ 32A
Three-
phase
Rated voltage
100-240VAC 50~60Hz
Maximum total load
current
3×16A, 3×32A

5
Direct
current
Rated voltage
240VDC/ 336VDC
Maximum total load
current 40A/ 60A
Output socket system
See "Socket Standard and
Output Unit Configuration
Table" for details.
Output unit specification
Accept customized production
Monitoring function (Local)
Voltage (V), Current (A), Active
Power(kW), Energy (kWh)
Alarm Alarm condition
When total load
current/voltage current
exceed the rated value
Alarm method
Buzzer alarm
Physical
characteristics
Product dimensions
Depends on the actual model
Properties of shell material
ABS & PC
Case color
Black
Mounting Style
Side brackets mounting/
Rear button mounting
Environment
Working temperature
0℃~45℃
Relative humidity
30~90%
Storage temperature
-20℃~ +70
℃
This is a Class A product. In home environment, this product may cause radio interference.
In this case, the user may be required to take appropriate measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping
content. If the Declaration of Conformity is missing, you can request it by post under the below
mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany