Digitus DA-70550-1 User manual

IDE to USB2.0
HDD External Enclosure 2.5
(DA-70550-1)
User Manual

I. Foreword
Congratulations on your purchase of our product! We will show you
a new storage concept with safety and convenience. It is our
pleasure to give you the best solution to expand your HDD`s
Capacity and enhance your data`s reliability in PC system or Mac
system. Before using the product, please read this manual
carefully for further recognizing of the product.
II. System Requirement
Basic environment for setup this device:
Hardware requirement: a PC, Notebook or Mac system with free
USB interface;
Operation system: Windows98SE/ME/2000/XP/Vista/7, Mac OS 8.6 or above.
III. Feature
* Compliant with USB2.0/USB1.1 standard
* Support Plug-Play and Hot-Plug.
* Transfer rate available for 480Mb/s,12Mb/s.
* Power Supply: Bus power or self-power.
IV. Package
Check fittings
Before using the product, please check the fittings in the
package compliant with the below. If not, please contact the local
dealers timely.
* one USB Enclosure
* one USB Combination cable
* one User 's Manual
* one CD Driver

V. Hardware Installation
Install a 2.5" IDE HDD into the enclosure
1. Put out the PCB board with back case.
2. Paste the HDD label to the HDD bottom.
3. Attach the 2.5" hard disk drive (HDD) to the 44pin connector of
the PCB board
4. Slide the HDD with PCB board into box
5. Fix the screws tightly.

VI. Driver Installation
a. Driver setup mode under Windows98SE
1)Start the operating system mentioned above
2)Connect the USB external box(which have installed a HDD) and PC
with USB cable
3)System will automatically detect new device and search the suitable
driver
4)Insert the CD driver and select [search available driver], and click
[Browse]
5)Point and select the relative disk drive such as [G]
6)System will find the suitable file and finish the installation
Automatically.
b. Setup under Windows2000/XP/Vista/7
Under system Windows Me/2000/XP/Vista/7, system will automatically
detect the new hardware and finish setup!
c. Setup mode under Mac OS system
If your system is Mac OX 8.6 or above, the system can find the
driver direvtly. If your system is 8.6 , you have to download and
setup"USB MASS STORAGE SUPPORT1.3.5"from SOFTWARE
SUPPORT
Website:http://www.apple.com/support
VII. Power Supply:
If your HDD needs more than 500mA for function or work
stably while using only the USB Bus-power, you should apply an external power supply
for this unit

Connect the USB extended power jack:
1. Connect the HDD installed enclosure to your computer's USB/FW
port with the USB2.0 multiple/FW cable
2. Connect the red color of USB extended power jack which been
mounted on the enclosed USB2.0 multiple cable to your computer's
the other USB port
DATA USB Connector
To External Box
Mini USB Port Color:RED
Power USB Connector
Warning:
Before removing this unit from your computer, please finish the
following procedures for a safe removal:
1). Click the icon in the [Desktop] window of your computer
2). A [Safely Remove Hardware] message window will appear, click
the [Stop] button
3). [It is now safe to remove the USB device] message will appear,
close the [Safely Remove Hardware] window
4). Remove (Power off) the USB extended power jack if it is applied.
Now you can safely remove the enclosure!

Disclaimer
All the information in this document is subject to change without prior notice The
manufacturer makes no representations or any warranties regarding the Contents of this
manual. The information contained in this manual is provided for the general use by the
customers. No part of this document may be reproduced or transmitted in any form by
any means without the express written permission of The manufacturer. All brand names
and product names used in this document are trademarks or registered trademarks of
their respective holders.