Digitus DA-90388 User manual

Instruction Manual
ELECTRIC
SIT-STAND DESK
DA-90388 • DA-90389 • DA-90390

2
| Preface
This electric height adjustable standing desk consists of a heavy-duty steel desk frame and a motorized height adjustment system.
Please read and completely understand this manual before installation in order to make sure the safe and correct use of the system
and maintain the longevity of the overall construction and the built-in electronics.
Hereby Assmann Electronic GmbH declares that the Declaration of Conformity is part of the shipping content.
If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address
www.assmann.com | Assmann Electronic GmbH | Auf dem Schüffel 3 | 58513 Lüdenscheid | Germany
Instructions of Safety and Warnings:
•Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury
•Any incomplete observation of the instructions, warnings and additional information marked with the "Note" and ""
may result in serious damage to the system or its components.
•This product can be used by children aged from 8 years and above if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision. Unplug the desk when the system isn't in use,
and place the power plug out of children reach.
•Persons with reduced physical, mental abilities and or lack of experience and knowledge must not use the product,
unless they're under supervision, understand the hazards involved or they have been thoroughly instructed in the
use of the apparatus by a person who is responsible for the safety of these persons.
•Users should make sure that they never sit on the desktop in order to prevent serious bodily injury.

3
Electrical Safety Instructions:
The product is powered by electricity. In order to avoid burns, fire and electric shock, please read the instructions carefully.
Don't clean the product with water
while the power is still connected.
Never operate the system if it's in moist environment
or its electrical components have contact with liquids.
Don't disassemble or replace components
while the power is still connected.
Don't operate the system if the control box makes noise or odor.
Alterations of the given power unit and control box aren't allowed.
Never operate the system with a damaged cord
or plug. Please contact your point of purchase to
replace the damaged parts.
Other Safety Instructions:
•Clear up all obstacles within the height adjustment range.
•Don't leave the cords or plug unorganized in order to prevent tripping hazards.
•Any attempts to reconstruct the desk frame aren't allowed.
•Don't add anything to the adjustable junctions of the desk frame.
•Outdoor use is prohibited.

4
| Preparation
What are the specifications
you need to know?
Weight Capacity
125kg (275lbs)
Power input
(100-240V)
Operation Temperature
(-5°C ~+40°C)
What are the tools you
require while installation?
Bubble Level
Allen Wrench
(Included)
Drill
Screwdriver
What's the thing you'd
better have before
installation?
A Shipping Blanket
to protect the desk
and the floor
Things you need to know
before installation
Please check all of the components shown in the component checklist. If any of the
components are missing or damaged, contact your point of purchase for a replacement.
Disposal: The product with this mark indicates that this product shouldn't be disposed with
other household wastes throughout the EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the local recycle
service or contact your point of purchase to withdrawn the product.

5
| Checklist and Installation
A (x1)
Crossbar
B (x2)
Side Bracket
C (x2)
Lifting Column
D (x2)
Foot
E (x1)
Fixing Plate
F (x1)
Control Box
G (x1)
Power Plug
H (x1)
Cable Management Tray
The picture of the controller is for
your reference only. Actual product
may vary.
I (x2)
Tray Hanger
J (x1)
Controller
This page can be torn so that it's easier for you to match the components with the images.

6
S-A (x8)
Hex Head Screw
S-B (x8)
Hex Head Screw
S-C (x10)
Head Screw+ 1 Spacer
S-D (x2)
Head Screw
S-E (x2)
Head Screw
S-F (x4)
Head Screw
S-G (x3)
Cable Clip
S-H (x10)
Anti-Vibration Pad
S-I (x1)
Allen Wrench
Now let's start the installation.

7
| Attaching Side Brackets
Please prepare a spacious area for installation, and put a shipping blanket on the area to prevent scratches.
Carefully place the desktop(not included) upside down on the blanket
Place the crossbar and side brackets on the top.
Attach the side brackets to the end of the crossbar . (This step doesn't require the use of the screws.)
Note: The drawings of both of the crossbar and side brackets are the backside of the components. Please make sure
the crossbar and side brackets keep facing down while installation, which is convenient for the further steps.
Shipping
Blanket

8
| Adjusting the Frame
Loosen the hex head screws that fix the
adjustable junction, but don't completely
take out the screws.

9
Ensure that the frame is placed in the center of the table.
Then adjust the frame to suit the size of the tabletop.
When adjusting the frame position, please make sure it doesn't exceed the range of silk screen printing on the inner crossbar.

10
Retighten all the hex head screws
to finish the adjustment.

11
| Drilling Mounting Holes
Use a drill to make mounting holes on the backside of the
tabletop through the 8 mounting holes on the side brackets.
Note:The depth of the mounting holes should be over 10mm
and the diameter should be less than 3mm.
Drill

12
| Assembling the Lifting Columns
Insert one lifting column into one end of the crossbar with
the head of the lifting column facing inward. Make sure the
mounting holes on the lifting column completely align with
the screw holes on the crossbar.
Fix the lifting column with crossbar using 4 screws
with the Allen wrench .
Repeat the same process to assemble the other lifting
column

13
| Assembling the Feet
Place the foot on the bottom of the lifting column.
Align the mounting holes on the foot with the screw
holes on the lifting column.
Fix the foot using 4 screws with the
Allen wrench .
Repeat the same process to assemble the other foot.

14
| Assembling the Fixing Plate
Align the mounting holes on the fixing plate with the screw holes as shown.
Attach the fixing plate on the center of the crossbar with 2 screws using a screwdriver.
Note: The arrow on the fixing plate indicates the direction of sliding in the control box.
Follow the direction of the arrow to mount the control box in the next step.
The fixing plate can be attached to either of
the right side and the left side.
Screwdriver

15
| Attaching the Control Box
Turn over the desk frame with the crossbar facing up.
At least two people are required when turning over the
desk frame. If only one person turns over the desk frame,
serious bodily injuries might occur.
Connect the cords, control box and motors.
CAUTION
Note:
Please make sure the slot on the control box is facing upward.
There is no corresponding relation between the motor ports and
the lifting columns.
The picture of the controller is for your reference only.
Actual product may vary.
Connect the two motor cords to the two ports
marked "M1" and "M2" (one on each side of the
control box).
Connect the controller cord to the port
marked "HS".
Insert the power plug in the port marked "AC".

16
The arrow on the fixing plate indicates the direction of sliding in the control box
Follow the direction of the arrow to mount the control box.
Slide the control box to the center of fixing plate.

17
| Assembling the Cable Management Tray
Align the mounting holes on the tray hangers with the
screw holes on the cable management tray.
Assemble the tray hangers to the cable management tray
with 4 screws from below using a screwdriver
Hang the cable management tray on
the crossbar as shown.
Screwdriver

18
Tighten the knobs on the tray hangers.

19
| Assembling the Desktop
Attach the anti-vibration pad to the surface of the crossbar
on the ten positions as shown.

20
Align the previously drilled screw holes with the mounting holes on the crossbar.
Insert and tighten the 4 screws from below.
Repeat the same process to assemble the
other side of the desktop.
Screwdriver