Digitus DN-82030 User manual

10/100M Fast Ethernet Media Converter
User’s Manual
DN-82030
Overview
The 10/100M Fast Ethernet Media Converter series is designed to meet the massive
needs for network deployment and able to extend a copper based Fast network via
fiber cable to a maximum distance up to 120KM. Our 10/100M Fast Ethernet Media
Converter series is fully compliant with IEEE802.3, IEEE802.3U, 10/100Base-TX,
100Base-FX, standards. It can be installed into a Standard Converter Chassis. The
installation & operation procedures are simple & straightforward. Operation status
can be locally monitored through a set of Diagnostic LED located in the front panel.
Features
10/100Base-TX to 100Base-FX Converter
Standards:IEEE802.3, IEEE802.3U, 10/100Base-TX, 100Base-FX
Interface: 1 x RJ-45 connector, 1 x SC/ST fiber connector
(If needed, we can offer converters with 2 or 4 RJ-45 ethernet ports.)
Flow Control: TEEE802.3x flow control for full duplex mode.
Back-pressure flow control for half duplex model.
LED: Power, FX,FX-LINK/ACT,FDX,TX-100,TX-LINK/ACT
Packing list
The box should contain the following items:
-The Media Converter
-AC-DC Power Adapter (for external models) or Power Cord (for internal models)
-The User’s Manual
-Warranty Card
Please notify your sales representative immediately if any items are missing or
damaged.

Installation
•Attach fiber cable from the media converter to the fiber network. The fiber
connections must be matched - transmit socket to receive socket, the TX, RX
fiber cable must be paired at both ends.
•Attach a UTP cable from the 10/100BASE-T network to the RJ-45 port on the
media converter.
•Connect the power adapter to the media converter and check that the Power
LED lights up. The TX-LINK/ACT and FX-LINK/ACT LEDs will light up when all the
cable connections are satisfactory.
Table 1:
Fig 1: Front panel for dual fiber media converter
Fig 2: Front panel for single fiber media converter
LED Description
LED indicator lamp Status Description
PWR On When power supply is normal
Off When power supply fail
100M On When TP Port Link speed is 100M
Off When TP Port Link speed is 10M
TX Link/Act
On
Connection status display for electric link.
“ON” indicates that electric link is in correct
connection.
Blink Active status display of electric link
“Blink” indicates data transmitting
FX Link/Act
On
Connection status display for fiber link
“ON” indicates that electric link is in correct
connection.
Blink Active status display of fiber link
“Blink” indicates data transmitting

FDX/COL On Fiber port works in the full duplex mode
Off Fiber port works in the half duplex mode
SD On Fiber signal is detected
Off Fiber signal not detected
Technical Specifications
1. Standard Protocol: IEEE802.3 10 Base-T standard
IEEE 802.3u 100Base-TX/FX standard
2. Connector: one RJ-45 connector, one SC/ST fiber connector.
3. Operation mode: full duplex mode or half duplex mode
4. Power supply parameter: outside: 5V DC 1A
Built-in: 110-265V AC 48VDC
5. Environmental temperature: 0°C-60°C
6. Relative humidity: 5%-90%
7. TP cable: Cat5 UTP cable
8. Fiber: 50/125, 62.5/125um multi-mode fiber; 9/125, 10/125um single-mode
fiber.
9. Dimensions:
External power supply: 26mm x 71mm x 94mm
Built-in power supply: 40mm x 110mm x 140mm
Cautions:
1. This product is suitable for indoor application.
2. Put on the dust cover of fiber interface when not used.
3. It is forbidden to stare at the TX fiber-transfer end with naked eyes.
Hereby ASSMANN Electronic GmbH, declares that this device is in compliance with the
requirements of Directive 2014/30/EU (EMC), Directive 2014/35/EU (LVD) and the Directive
2011/65/EU for RoHS compliance. The complete declaration of conformity can be requested
by post under the below mentioned manufacturer address.
Warning:
This device is a class B product. This equipment may cause some radio interference in living
environment. In this case, the user can be requested to undertake appropriate measures to
prevent interference.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany