Digitus DN-95323-1 User manual

Fast Ethernet PoE af/at 8-port
Switch + 2 uplinks
User Manual
DN-95323-1 Rev. 2

Package Contents
Check the following contents of
your package:
 PoE Switch x1
 User Manual x1
 Power Cord x1
 Accessories
(Rubber Feet*4, 19” bracket*2)
If any part is lost and damaged, please contact your local
agent immediately.
Introduction
The DIGITUS® 8-port Fast Ethernet Switch with 8 Power over
Ethernet ports provides your network a noticeable
improvement in performance and efficiency. Thanks to PoE+
(30W) support, you only need one cable (network cable) for
power and data transfer. This enables you to expend your
network even where no power lines or outlets are available.
The switch doesn't need a configuration so a fast and seamless
integration you’re your network is guaranteed. With the
integrated DIP switch, you can activate the VLAN mode (Virtual
Local Area Network). By the port separation an optimal and
time-saving identification of the connected devices (e.g.
IP-Network cameras) is possible without using a web interface.
Multicast and broadcast requests are also prevented via the
port-based VLAN function. The Extensive mode can be used to
extend the range by up to 250 m at 10 Mbps.

Hardware Description
Front Panel
The Front Panel Consists of Ethernet Ports. The LED indicators
are also located on the panel.
DIP Switch
The DIP switch located on the left panel.
Default: The factory default mode, normal communication
between port 1~10.
VLAN: Port 1-8 are isolated to stop broadcast Storm and
increase forwarding rate of frame but can
communicate via uplink port 9 and 10 CCTV Up to
250m PoE distance allows you to expand you
network via Ethernet cable to where there is no
power Line or outlet. Network speed will be
reduced to 10Mbps
Note: After change the mode, in order to make the
corresponding configuration take effect you need to manually
restart

LED indicator
LED Color Function
PWR Green
Off: No Power supply
Light: Indicates the switch has power
LNK/
ACT Green
Off: No device is connected to the
corresponding port
Light: Indicates the link through that
port is successfully Established at
10/100Mbps
Blink: Indicates that the Switch is
actively sending or receiving data over
that port
PoE Orange
Off: No PoE powered device (PD)
connected
Light: There is a PoE PD connected to
be port
Blink: Indicates port abnormal PoE
function
Rear Panel
The rear panel of the PoE Switch indicates an AC inlet power
socket, which accepts input power from 100 to
240V AC, 50/60HZ.

Power socket
Connect the female connector of the power cord here, and the
male connector to the AC (Alternating Current) power outlet.
Please make sure the voltage of the power supply meets the
requirement of the input voltage
Grounding column
The switch already comes with lightning protection mechanism.
You can also ground the switch through the PE (Protecting
Earth) cable of AC cord or with Ground Cable.
Installation of the Switch
This part describes how to install your Ethernet Switch and
make connections to it. Please follow the following instructions
to avoid incorrect installation causing device damage and
security threat.
Before cleaning the switch, unplug the power plug of the
switch first. Do not clean the switch with wet cloth or
liquid
Do not place the switch near water or any damp area
Prevent water or moisture from entering the switch
chassis
Do not place the switch on an unstable case or desk.
The switch might be damaged severely in case of a fall

Ensure proper ventilation of the equipment room and
keep the ventilation vents of the switch free of
obstruction
Make sure that the operating voltage is the same one
labeled on the switch
Do not open the chassis while the switch is operating or
when electrical hazards are present to avoid electrical
shocks.
Desktop Installation
Install the Switch on a desktop, please attach these cushioning
rubber feet provided on the bottom at each corner of the
Switch in case of external vibration. Allow adequate space for
ventilation between the device and the objects around it.

Wall-mounted installation
Fix the two screws on the wall as shown in the figure below
Place the switch smoothly on the screws to fix it to the wall
Turn on the switch
Please connect the AC power cord into the rear of the switch
and to an electrical outlet (preferably one that is grounded).
When the switch is power on, the LED indicators flash
momentarily for one second, which represents a resetting of
the system. The Power LED indicator turns on green.
Note: Please confirm the voltage is correct before power
on, otherwise the switch will be damaged.
(The power input is: 100V-240Vac, 50/60Hz.)

Specifications
Model
8*FE (PoE)+2FE Uplink PoE Switch
Standard
IEEE802.3, IEEE802.3u, IEEE802.3az,
IEEE802.3x, IEEE802.3af, IEEE802.3at
Network Media
10BASE-T:
UTP category 3,4,5 cable (≤100m)
100BASE-TX:
UTP category 5 cable (≤100m)
MAC Address Table
1K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
Switching Capacity
2G
Dimensions (L*W*H)
220 *150*44mm
Fan
Fanless
Power Input
AC: 100~240V, 50/60Hz
PoE Port
Port 1~8
PoE Power on RJ45
Mode A 1/2(+), 3/6(-)
PoE Power Output
Voltage: 55V DC
Power: 30W(Max)
PoE Power Budget
120W
Temperature
Operating Temperature:
0°C ~ 40 °C (32 °F ~104°F)
Storage Temperature:
-40 °C ~ 70 °C (-40 °F ~158°F)
Humidity
Operating Humidity:
10% ~ 90% non-condensing
Storage Humidity:
5% ~ 90% non-condensing

This is a Class A product. In home environment, this product may cause radio
interference. In this case, the user may be required to take appropriate
measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of
Conformity is part of the shipping content. If the Declaration of Conformity is
missing, you can request it by post under the below mentioned manufacturer
address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany