Digitus DN-95320-1 User manual

Fast Ethernet PoE Switch
4-port PoE + 1-port uplink,
60W PoE Budget
Quick Installation Guide
DN-95320-1

2
Copyright Statement
Our company reserves all copyrights of this document. Any
reproduction, excerption, backup, modification, transmission,
translation or commercial use of this document or any portion
of this document, in any form or by any means, without the
prior written consent of our company is prohibited.
Exemption Statement
This document is provided "as is". The contents of this
document are subject to change without any notice. Please
obtain the latest information through our company website.
Our company endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused
due to content omissions, inaccuracies or errors.
1. Product Introduction
The DIGITUS DN-95320-1 is a 5-Port 10/100M Desktop PoE
Switch, that enables a seamless network connection. It
integrates 100 Mbps Fast Ethernet and 10 Mbps Ethernet
network capabilities. These PoE ports can automatically
detect IEEE 802.3af/at-compliant Powered Devices (PDs) and
supply them with power. The operating mode can be changed
using the slide switch on the front side.
When switching into extend mode, Ports 2-5 can be switched
into long range mode at up to 250 meters with 10 Mbps.
The DN-95320-1 is easy to install and to use. It does not
require any configuration or installation. With its desktop
design, outstanding performance and quality, the 5-Port
10/100 Desktop PoE Switch is an excellent choice for
extending video monitoring or WLAN access points.

3
1.1 Features
PoE support: Port 1-4 (802.3 af/at)
PoE total output: 60 watts
4 RJ45 PoE Ports
An RJ45 port can also be used as an uplink port
External power supply, sophisticated design, suitable for
desktop installation
LED displays: PoE, link, activity
Supports data transfer of up to 250 m at a rate of 10 Mbps.
Automatically detects PoE devices on connection, devices
that are not PoE-capable can also be used.
1.2 Package Contents
Before installing the Switch, make sure that the following the
"packing list" listed OK. If any part is lost and damaged,
please contact your local agent immediately. In addition,
make sure that you have the tools install switches and cables
by your hands.
1 x 5-Port 10/100Mbps Ethernet
Unmanaged PoE Switch (4-Port PoE).
1 x Installation Component
1 x DC Power Adapter
1 x Quick Installation Guide

4
1.3 Hardware Specifications
Standards
IEEE802.3i, IEEE802.3u,
IEEE802.3x, IEEE802.3az,
IEEE802.3at, IEEE802.3af
Interface
5 x 10/100Mbps
Auto-Negotiation ports
Mode switch

Default mode:1-5 port speed
rate 100 Mbps, communicate
with each other
Extend mode:1port speed rate
100Mbps,2-5 PoE port rate of
10 Mbps, the farthest distance
is 250m, communicate with
each other
Network Media
10Base-T: UTP 5e and
above cable (maximum 250m)
100Base-Tx: UTP category 5,
5e cable (maximum 100m)
Transfer Method
Store-and-Forward
MAC Address Table
1K
Switching Capacity
1Gbps
Packet Forwarding Rate
0.744 Mpps
PoE Ports(RJ45)
4x PoE ports compliant with
802.3at/af
Power Pin Assignment
4/5(+), 7/8(-)
PoE Budget
60W
LED
indicators
Per Port
Link/Act: Green PoE: Orange
Per Device
Power: Green
Power Supply
DC 53.5V,1.2A External Power
Power Consumption
Maximum (PoE on):
66.5W (220V/50Hz)

5
Dimensions (W x D x H)
89.3*81.7*21.3mm
Environment

Operating Temperature:
0℃- 45℃
Storage Temperature:
-40℃- 70℃
Operating Humidity:
10%~90% RH non-condensing
Storage humidity:
5%~90% RH non-condensing
1.4 External Component Description
Front Panel
The front panel of the Switch consists of one power LED
indicator, five Link/Act LED indicators, four PoE LED indicators
and one slide switch as shown as below.
Default/Extend mode switch:
It can through the front panel of the slide switch to switch
working mode. When switch to Extend mode, 2-5 port rate
negotiation into 10 Mbps, Data transmission and power
supply can reach as far as 250 meters.

6
You can with LED indicator quickly judge the Switch work, help
diagnose problems in the Switch or the connected devices.
LED indicator as shown below:
LED indicators:
The LED Indicators will allow you to monitor, diagnose and
troubleshoot any potential problem with the Switch,
connection or attached devices.
The following chart shows the LED indicators of the Switch
along with explanation of each indicator.
LED
Indicator
Faceplate
Marker
Status Indication
Power
Indicator PWR
Off Power Off
Solid
green
Power On
10/100
BASE-T
adaptive
Ethernet
port
indicators
(1-5)
Link/Act
Off
The port is
NOT connected.
Solid
green
The port is connected,
but no data is
transmitting or
receiving.
Blinking
The port is transmitting
or receiving data.

7
PoE status
indicators
(2-5)
PoE
Off
No PD is connected to
the corresponding port,
or there is a
breakdown.
Solid
orange
A Powered Device is
connected to the port,
which supply power
successfully.
Blinking
The PoE power current
may be overloaded
Rear Panel
The rear panel of the Switch consists of 5 x 10/100Mbps RJ-
45 ports and a power connector as shown as below.
10/100Mbps RJ-45 ports (1~5):
Designed to connect to the device with a bandwidth of
10Mbps or 100Mbps. Each has a corresponding 10/100Mbps
LED, port2~port5 support PoE power supply function, each
has a corresponding PoE LED.
UP-link port:
Up-link port as an automatic flip cascade port, can be used
with the other 4 RJ-45 ports, the port corresponds to the
Link/Act indicator.

8
Power Connector:
Power is supplied through an external DC power adapter. It
supports 53.5V DC.
2. Installing and Connecting the Switch
This part describes how to install your PoE Ethernet Switch
and make connections to it. Please read the following topics
and perform the procedures in the order being presented.
2.1 Installation
Please follow the following instructions in avoid of incorrect
installation causing device damage and security threat.
Put the Switch on stable place or desktop in case of
falling damage.
Make sure the Switch works in the proper DC input and
matches the voltage labeled on the Switch.
To keep the Switch free from lightning, do not open the
Switch's shell even in power failure.
Make sure that there is proper heat dissipation from and
adequate ventilation around the Switch.
Make sure the cabinet to enough back up the weight of
the Switch and its accessories.

9
2.2 Desktop Installation
When installing the Switch on a desktop, please attach these
cushioning rubber feet provided on the bottom at each
corner of the Switch in case of the external vibration. Allow
adequate space for ventilation between the device and the
objects around it.
2.3 Power on the Switch
The Switch connected an external power adapter power
53.5V/1.2A supply, make sure you use the proper power
supply.
2.4 Connect Computer (NIC) to the Switch
Please insert the NIC into the computer, after installing
network card driver, please connect one end of the twisted
pair to RJ-45 jack of your computer, the other end will be
connected to any RJ-45 port of the Switch, the distance
between Switch and computer is around 100 meters. Once
the connection is OK and the devices are power on normally,
the LINK/ACT status indicator lights corresponding ports of
the Switch.

10
2.5 Switch connection to the PD
2~5 port of the Switch have PoE power supply function, the
maximum output power of single port up to 30W, it can make
PD devices, such as internet phone, network camera, wireless
access point work. You only need to connect the Switch PoE
port directly connected to the PD port by network cable.
Hereby Assmann Electronic GmbH, declares that the Declaration of
Conformity is part of the shipping content. If the Declaration of
Conformity is missing, you can request it by post under the below
mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany