Diivoo WT-04 User manual
Dual water timer
More effectively manage your garden
USER MANUAL
Press the " ", the " " points to Auto and the
program will be running as you set before.
WT-04
The default display of Start time is OFF. Press the
" " button to set the time to start water-
ing, and press" " button to confirm.
Start Time
Press the " " to set the time of watering duration,
and press " " to confirm.
Watering can be customized to run from 1 min to
23hours 59 mins.
How long
1. Press the " ", the " " points to Set Time.
2. Press the " " to set the current hour and
minute. Press " " to confirm.
3. Press the " " to set the current day of the
week. Press " " to save changes and moving
to next setting, Program.
Please make sure the timer is in AutoRun states
when set Rain Delay or Children Lock.
2
3
Need Help?
Thank You!
1. Product Appearance 3. Automatic Watering Program Setting
Attention
Program Logic
2. Indicators Introduction
Children Lock
Rain Delay
Watering State
Battery Indicator
Select P1/P2/P3
For Watering
Select Zone
For Watering
The Next
Watering Time
· The watering duration ranging from 00:00-23:59
If the hour of watering duration is set to 00，aer
switching, the program is OFF.
Note:
Note:
1Set Time - Set the current week and time
4
Auto
1. Press the " ", the "▲" points to Program. And
press the button to set Zone1/Zone2，press
" " to confirm.
2. P1 have been selected and Press " "if
switch to P1/P2/P3.
1. Press the " ", OFF is displayed. By pressing
" ",the time can be changed.
2. Hours/minutes can be switched cyclically.
Program 1 State
1
2Set Z1/P1
Follow the steps likes Z1/P1 setting to set Z1/P2,Z1/P3.
(Set Zone/Program-start time-How long-water days)
3Z1/P2,Z1/P3... Setting
Step1: SET TIME
Step2: SET PROGRAM
Step3
AutoRun
Set Z1-Set the Zone for watering
Set P1-Set the Program for watering
How long: Minutes or hours
Set Water Days-Set the days of the
week to run
Start
Set the current time and week
support@diivoosmart.com
If you have any questions, please feel free to contact us first.
We are always here for you. Press the " " button, the " " points to OFF, the
screen shows OFF and the battery level.
All program are saved but the timer stop working.
5
OFF
·The Water days can be cancelled when press " "
button again if the week has been selected.
·The day will come with a 【】 if be selected.
Set Water Days
4
Press the " " to choose the day of the week
you would watering, and press " " to confirm.
Note:
Start time: 00:00-23:59
Manual Watering
Button
3 Separate Watering
Programs Button
2 Independent
Controlled Outlets
Decrease Button
Confirm Button
Setting Button
Increase button
Hose Faucet Connection
Outlet
Fitting NH3/4”
Filter
Z1/P2~P3, Z2/P1~P3 : the same
as Z1/P1(start from step 2)
Dual water timer
More effectively manage your garden
USER MANUAL
Press the " ", the " " points to Auto and the
program will be running as you set before.
WT-04
The default display of Start time is OFF. Press the
" " button to set the time to start water-
ing, and press" " button to confirm.
Start Time
Press the " " to set the time of watering duration,
and press " " to confirm.
Watering can be customized to run from 1 min to
23hours 59 mins.
How long
1. Press the " ", the " " points to Set Time.
2. Press the " " to set the current hour and
minute. Press " " to confirm.
3. Press the " " to set the current day of the
week. Press " " to save changes and moving
to next setting, Program.
Please make sure the timer is in AutoRun states
when set Rain Delay or Children Lock.
2
3
Need Help?
Thank You!
1. Product Appearance 3. Automatic Watering Program Setting
Attention
Program Logic
2. Indicators Introduction
Children Lock
Rain Delay
Watering State
Battery Indicator
Select P1/P2/P3
For Watering
Select Zone
For Watering
The Next
Watering Time
· The watering duration ranging from 00:00-23:59
If the hour of watering duration is set to 00，aer
switching, the program is OFF.
Note:
Note:
1Set Time - Set the current week and time
4
Auto
1. Press the " ", the "▲" points to Program. And
press the button to set Zone1/Zone2，press
" " to confirm.
2. P1 have been selected and Press " "if
switch to P1/P2/P3.
1. Press the " ", OFF is displayed. By pressing
" ",the time can be changed.
2. Hours/minutes can be switched cyclically.
Program 1 State
1
2Set Z1/P1
Follow the steps likes Z1/P1 setting to set Z1/P2,Z1/P3.
(Set Zone/Program-start time-How long-water days)
3Z1/P2,Z1/P3... Setting
Step1: SET TIME
Step2: SET PROGRAM
Step3
AutoRun
Set Z1-Set the Zone for watering
Set P1-Set the Program for watering
How long: Minutes or hours
Set Water Days-Set the days of the
week to run
Start
Set the current time and week
support@diivoosmart.com
If you have any questions, please feel free to contact us first.
We are always here for you. Press the " " button, the " " points to OFF, the
screen shows OFF and the battery level.
All program are saved but the timer stop working.
5
OFF
·The Water days can be cancelled when press " "
button again if the week has been selected.
·The day will come with a 【】 if be selected.
Set Water Days
4
Press the " " to choose the day of the week
you would watering, and press " " to confirm.
Note:
Start time: 00:00-23:59
Manual Watering
Button
3 Separate Watering
Programs Button
2 Independent
Controlled Outlets
Decrease Button
Confirm Button
Setting Button
Increase button
Hose Faucet Connection
Outlet
Fitting NH3/4”
Filter
Z1/P2~P3, Z2/P1~P3 : the same
as Z1/P1(start from step 2)
Dual water timer
More effectively manage your garden
USER MANUAL
Press the " ", the " " points to Auto and the
program will be running as you set before.
WT-04
The default display of Start time is OFF. Press the
" " button to set the time to start water-
ing, and press" " button to confirm.
Start Time
Press the " " to set the time of watering duration,
and press " " to confirm.
Watering can be customized to run from 1 min to
23hours 59 mins.
How long
1. Press the " ", the " " points to Set Time.
2. Press the " " to set the current hour and
minute. Press " " to confirm.
3. Press the " " to set the current day of the
week. Press " " to save changes and moving
to next setting, Program.
Please make sure the timer is in AutoRun states
when set Rain Delay or Children Lock.
2
3
Need Help?
Thank You!
1. Product Appearance 3. Automatic Watering Program Setting
Attention
Program Logic
2. Indicators Introduction
Children Lock
Rain Delay
Watering State
Battery Indicator
Select P1/P2/P3
For Watering
Select Zone
For Watering
The Next
Watering Time
· The watering duration ranging from 00:00-23:59
If the hour of watering duration is set to 00，aer
switching, the program is OFF.
Note:
Note:
1Set Time - Set the current week and time
4
Auto
1. Press the " ", the "▲" points to Program. And
press the button to set Zone1/Zone2，press
" " to confirm.
2. P1 have been selected and Press " "if
switch to P1/P2/P3.
1. Press the " ", OFF is displayed. By pressing
" ",the time can be changed.
2. Hours/minutes can be switched cyclically.
Program 1 State
1
2Set Z1/P1
Follow the steps likes Z1/P1 setting to set Z1/P2,Z1/P3.
(Set Zone/Program-start time-How long-water days)
3Z1/P2,Z1/P3... Setting
Step1: SET TIME
Step2: SET PROGRAM
Step3
AutoRun
Set Z1-Set the Zone for watering
Set P1-Set the Program for watering
How long: Minutes or hours
Set Water Days-Set the days of the
week to run
Start
Set the current time and week
support@diivoosmart.com
If you have any questions, please feel free to contact us first.
We are always here for you. Press the " " button, the " " points to OFF, the
screen shows OFF and the battery level.
All program are saved but the timer stop working.
5
OFF
·The Water days can be cancelled when press " "
button again if the week has been selected.
·The day will come with a 【】 if be selected.
Set Water Days
4
Press the " " to choose the day of the week
you would watering, and press " " to confirm.
Note:
Start time: 00:00-23:59
Manual Watering
Button
3 Separate Watering
Programs Button
2 Independent
Controlled Outlets
Decrease Button
Confirm Button
Setting Button
Increase button
Hose Faucet Connection
Outlet
Fitting NH3/4”
Filter
Z1/P2~P3, Z2/P1~P3 : the same
as Z1/P1(start from step 2)
Dual water timer
More effectively manage your garden
USER MANUAL
Press the " ", the " " points to Auto and the
program will be running as you set before.
WT-04
The default display of Start time is OFF. Press the
" " button to set the time to start water-
ing, and press" " button to confirm.
Start Time
Press the " " to set the time of watering duration,
and press " " to confirm.
Watering can be customized to run from 1 min to
23hours 59 mins.
How long
1. Press the " ", the " " points to Set Time.
2. Press the " " to set the current hour and
minute. Press " " to confirm.
3. Press the " " to set the current day of the
week. Press " " to save changes and moving
to next setting, Program.
Please make sure the timer is in AutoRun states
when set Rain Delay or Children Lock.
2
3
Need Help?
Thank You!
1. Product Appearance 3. Automatic Watering Program Setting
Attention
Program Logic
2. Indicators Introduction
Children Lock
Rain Delay
Watering State
Battery Indicator
Select P1/P2/P3
For Watering
Select Zone
For Watering
The Next
Watering Time
· The watering duration ranging from 00:00-23:59
If the hour of watering duration is set to 00，aer
switching, the program is OFF.
Note:
Note:
1Set Time - Set the current week and time
4
Auto
1. Press the " ", the "▲" points to Program. And
press the button to set Zone1/Zone2，press
" " to confirm.
2. P1 have been selected and Press " "if
switch to P1/P2/P3.
1. Press the " ", OFF is displayed. By pressing
" ",the time can be changed.
2. Hours/minutes can be switched cyclically.
Program 1 State
1
2Set Z1/P1
Follow the steps likes Z1/P1 setting to set Z1/P2,Z1/P3.
(Set Zone/Program-start time-How long-water days)
3Z1/P2,Z1/P3... Setting
Step1: SET TIME
Step2: SET PROGRAM
Step3
AutoRun
Set Z1-Set the Zone for watering
Set P1-Set the Program for watering
How long: Minutes or hours
Set Water Days-Set the days of the
week to run
Start
Set the current time and week
support@diivoosmart.com
If you have any questions, please feel free to contact us first.
We are always here for you. Press the " " button, the " " points to OFF, the
screen shows OFF and the battery level.
All program are saved but the timer stop working.
5
OFF
·The Water days can be cancelled when press " "
button again if the week has been selected.
·The day will come with a 【】 if be selected.
Set Water Days
4
Press the " " to choose the day of the week
you would watering, and press " " to confirm.
Note:
Start time: 00:00-23:59
Manual Watering
Button
3 Separate Watering
Programs Button
2 Independent
Controlled Outlets
Decrease Button
Confirm Button
Setting Button
Increase button
Hose Faucet Connection
Outlet
Fitting NH3/4”
Filter
Z1/P2~P3, Z2/P1~P3 : the same
as Z1/P1(start from step 2)
Dual water timer
More effectively manage your garden
USER MANUAL
Press the " ", the " " points to Auto and the
program will be running as you set before.
WT-04
The default display of Start time is OFF. Press the
" " button to set the time to start water-
ing, and press" " button to confirm.
Start Time
Press the " " to set the time of watering duration,
and press " " to confirm.
Watering can be customized to run from 1 min to
23hours 59 mins.
How long
1. Press the " ", the " " points to Set Time.
2. Press the " " to set the current hour and
minute. Press " " to confirm.
3. Press the " " to set the current day of the
week. Press " " to save changes and moving
to next setting, Program.
Please make sure the timer is in AutoRun states
when set Rain Delay or Children Lock.
2
3
Need Help?
Thank You!
1. Product Appearance 3. Automatic Watering Program Setting
Attention
Program Logic
2. Indicators Introduction
Children Lock
Rain Delay
Watering State
Battery Indicator
Select P1/P2/P3
For Watering
Select Zone
For Watering
The Next
Watering Time
· The watering duration ranging from 00:00-23:59
If the hour of watering duration is set to 00，aer
switching, the program is OFF.
Note:
Note:
1Set Time - Set the current week and time
4
Auto
1. Press the " ", the "▲" points to Program. And
press the button to set Zone1/Zone2，press
" " to confirm.
2. P1 have been selected and Press " "if
switch to P1/P2/P3.
1. Press the " ", OFF is displayed. By pressing
" ",the time can be changed.
2. Hours/minutes can be switched cyclically.
Program 1 State
1
2Set Z1/P1
Follow the steps likes Z1/P1 setting to set Z1/P2,Z1/P3.
(Set Zone/Program-start time-How long-water days)
3Z1/P2,Z1/P3... Setting
Step1: SET TIME
Step2: SET PROGRAM
Step3
AutoRun
Set Z1-Set the Zone for watering
Set P1-Set the Program for watering
How long: Minutes or hours
Set Water Days-Set the days of the
week to run
Start
Set the current time and week
support@diivoosmart.com
If you have any questions, please feel free to contact us first.
We are always here for you. Press the " " button, the " " points to OFF, the
screen shows OFF and the battery level.
All program are saved but the timer stop working.
5
OFF
·The Water days can be cancelled when press " "
button again if the week has been selected.
·The day will come with a 【】 if be selected.
Set Water Days
4
Press the " " to choose the day of the week
you would watering, and press " " to confirm.
Note:
Start time: 00:00-23:59
Manual Watering
Button
3 Separate Watering
Programs Button
2 Independent
Controlled Outlets
Decrease Button
Confirm Button
Setting Button
Increase button
Hose Faucet Connection
Outlet
Fitting NH3/4”
Filter
Z1/P2~P3, Z2/P1~P3 : the same
as Z1/P1(start from step 2)
Dual water timer
More effectively manage your garden
USER MANUAL
Press the " ", the " " points to Auto and the
program will be running as you set before.
WT-04
The default display of Start time is OFF. Press the
" " button to set the time to start water-
ing, and press" " button to confirm.
Start Time
Press the " " to set the time of watering duration,
and press " " to confirm.
Watering can be customized to run from 1 min to
23hours 59 mins.
How long
1. Press the " ", the " " points to Set Time.
2. Press the " " to set the current hour and
minute. Press " " to confirm.
3. Press the " " to set the current day of the
week. Press " " to save changes and moving
to next setting, Program.
Please make sure the timer is in AutoRun states
when set Rain Delay or Children Lock.
2
3
Need Help?
Thank You!
1. Product Appearance 3. Automatic Watering Program Setting
Attention
Program Logic
2. Indicators Introduction
Children Lock
Rain Delay
Watering State
Battery Indicator
Select P1/P2/P3
For Watering
Select Zone
For Watering
The Next
Watering Time
· The watering duration ranging from 00:00-23:59
If the hour of watering duration is set to 00，aer
switching, the program is OFF.
Note:
Note:
1Set Time - Set the current week and time
4
Auto
1. Press the " ", the "▲" points to Program. And
press the button to set Zone1/Zone2，press
" " to confirm.
2. P1 have been selected and Press " "if
switch to P1/P2/P3.
1. Press the " ", OFF is displayed. By pressing
" ",the time can be changed.
2. Hours/minutes can be switched cyclically.
Program 1 State
1
2Set Z1/P1
Follow the steps likes Z1/P1 setting to set Z1/P2,Z1/P3.
(Set Zone/Program-start time-How long-water days)
3Z1/P2,Z1/P3... Setting
Step1: SET TIME
Step2: SET PROGRAM
Step3
AutoRun
Set Z1-Set the Zone for watering
Set P1-Set the Program for watering
How long: Minutes or hours
Set Water Days-Set the days of the
week to run
Start
Set the current time and week
support@diivoosmart.com
If you have any questions, please feel free to contact us first.
We are always here for you. Press the " " button, the " " points to OFF, the
screen shows OFF and the battery level.
All program are saved but the timer stop working.
5
OFF
·The Water days can be cancelled when press " "
button again if the week has been selected.
·The day will come with a 【】 if be selected.
Set Water Days
4
Press the " " to choose the day of the week
you would watering, and press " " to confirm.
Note:
Start time: 00:00-23:59
Manual Watering
Button
3 Separate Watering
Programs Button
2 Independent
Controlled Outlets
Decrease Button
Confirm Button
Setting Button
Increase button
Hose Faucet Connection
Outlet
Fitting NH3/4”
Filter
Z1/P2~P3, Z2/P1~P3 : the same
as Z1/P1(start from step 2)
When you press the " " button again, the manual
watering task ends even if it is watering and the timer
will switch back to Auto mode.
Do not use your timer when the air tempera-
ture is below 40℉(4.5℃), the timers should
be removed from the hose faucet and stored
indoors to avoid potential frozen damage.
Filter can trap dirt particles, please clean
filter regularly and replace if worn.
Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel cadmium) batteries.
Used up or dead batteries must be removed
from the timer and disposed of properly.
Please replace batteries when the low
battery indicator appears the display. When
replacing the power unit, please make sure
that the water timer is dry.
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries.
· Please do not insert rechargeable batteries to avoid
low voltage.
· The display will turn on for 3 seconds when power on.
Please make sure the timer is in Auto Run state.
1. Press the " " and Zone 1 have been select.
2. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 1. And Zone 2 have been select.
3. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 2.
Manual
· The timer don't have programmable
memory, it need to reset once power off.
1. Each program can only have one valve for watering.
2. If Z1 or Z2 is set to 00, the zone will not be watered.
Note:
6
Multi-Function
6. Precautions
4. Battery Installation
Note:
7. FAQ
Four batteries loaded are new 1.5V AA alkaline
batteries, make sure the batteries are properly placed
in the battery box. Do not use rechargeable batteries,
please you must use alkaline batteries.
A1:
Q1: The LCD screen does not display anything
when the batteries are installed.
Clock should be set to the correct time.
Start time is set to desired the time.
Rain Delay is on.
OFF mode is on.
The batteries are low.
The faucet is turned off.
A2:
Q2: Water does not come on at preset time.
Check if:
The O-ring is connected correctly to the hose tap.
The connection outlet or water pipe is broken.
The faucet and water pipe has a different thread.
If necessary, please use an appropriate adapter or
PTFE tape.
A3:
Q3: The hose tap connection/outlet leaks.
Check if:
If your are gravity feed system such as rain barrel system,
then it won't work and will keep low water pressure.
Gravity feed has no real pressure when dealing with a rain
barrel. It needs pressure measuring.
A4 :
Q4: Why is the water valve out of little water?
The timer have one year warranty, if you have any
questions, please feel free to contact via
The following conditions are not included in the warranty:
-Problems occur due to its use for other purposes, or
improper use or use of components not supplied by
Diivoo.
-Damages caused by improper use, for example, wrong of
power supply, artificial damage, etc.
8. After-sales Service
1
Inlet/Outlet Thread
Working Water Pressure
Working Temperature
Rain Delay Time
Waterproof
Included in the box
NH3/4"
7.25psi - 116psi
40.1˚ F-113˚ F
1 day and up to 7 days
IPX5
Watering Duration 00:01-23:59
5. Specification
· All Auto program are on hold during the rain delay.
If you want to cancel the Rain Delay, press " "
button 5s again.
· Rain delay allows you to postpone watering for 1
day and up to 7 days.
Note:
Please make sure the timer is in Auto Run state.
1. Hold and press " " button 5s until the appears
on the screen.
2. Press " " button to set the duration of the
delay from 1 to 7 days.
3. Press " " button it will start to watering.
Rain Delay
2
Please make sure the timer is in Auto Run state.
Hold and press " " button 5s until the " " appears
on the screen. If you want to cancel the " ", press
" " button 5s again.
Children Lock
3
1 x Water Timer,
2 x Threaded connector,
1 x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1 x Thread Seal Tape,
Instruction
When you press the " " button again, the manual
watering task ends even if it is watering and the timer
will switch back to Auto mode.
Do not use your timer when the air tempera-
ture is below 40℉(4.5℃), the timers should
be removed from the hose faucet and stored
indoors to avoid potential frozen damage.
Filter can trap dirt particles, please clean
filter regularly and replace if worn.
Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel cadmium) batteries.
Used up or dead batteries must be removed
from the timer and disposed of properly.
Please replace batteries when the low
battery indicator appears the display. When
replacing the power unit, please make sure
that the water timer is dry.
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries.
· Please do not insert rechargeable batteries to avoid
low voltage.
· The display will turn on for 3 seconds when power on.
Please make sure the timer is in Auto Run state.
1. Press the " " and Zone 1 have been select.
2. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 1. And Zone 2 have been select.
3. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 2.
Manual
· The timer don't have programmable
memory, it need to reset once power off.
1. Each program can only have one valve for watering.
2. If Z1 or Z2 is set to 00, the zone will not be watered.
Note:
6
Multi-Function
6. Precautions
4. Battery Installation
Note:
7. FAQ
Four batteries loaded are new 1.5V AA alkaline
batteries, make sure the batteries are properly placed
in the battery box. Do not use rechargeable batteries,
please you must use alkaline batteries.
A1:
Q1: The LCD screen does not display anything
when the batteries are installed.
Clock should be set to the correct time.
Start time is set to desired the time.
Rain Delay is on.
OFF mode is on.
The batteries are low.
The faucet is turned off.
A2:
Q2: Water does not come on at preset time.
Check if:
The O-ring is connected correctly to the hose tap.
The connection outlet or water pipe is broken.
The faucet and water pipe has a different thread.
If necessary, please use an appropriate adapter or
PTFE tape.
A3:
Q3: The hose tap connection/outlet leaks.
Check if:
If your are gravity feed system such as rain barrel system,
then it won't work and will keep low water pressure.
Gravity feed has no real pressure when dealing with a rain
barrel. It needs pressure measuring.
A4 :
Q4: Why is the water valve out of little water?
The timer have one year warranty, if you have any
questions, please feel free to contact via
The following conditions are not included in the warranty:
-Problems occur due to its use for other purposes, or
improper use or use of components not supplied by
Diivoo.
-Damages caused by improper use, for example, wrong of
power supply, artificial damage, etc.
8. After-sales Service
1
Inlet/Outlet Thread
Working Water Pressure
Working Temperature
Rain Delay Time
Waterproof
Included in the box
NH3/4"
7.25psi - 116psi
40.1˚ F-113˚ F
1 day and up to 7 days
IPX5
Watering Duration 00:01-23:59
5. Specification
· All Auto program are on hold during the rain delay.
If you want to cancel the Rain Delay, press " "
button 5s again.
· Rain delay allows you to postpone watering for 1
day and up to 7 days.
Note:
Please make sure the timer is in Auto Run state.
1. Hold and press " " button 5s until the appears
on the screen.
2. Press " " button to set the duration of the
delay from 1 to 7 days.
3. Press " " button it will start to watering.
Rain Delay
2
Please make sure the timer is in Auto Run state.
Hold and press " " button 5s until the " " appears
on the screen. If you want to cancel the " ", press
" " button 5s again.
Children Lock
3
1 x Water Timer,
2 x Threaded connector,
1 x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1 x Thread Seal Tape,
Instruction
When you press the " " button again, the manual
watering task ends even if it is watering and the timer
will switch back to Auto mode.
Do not use your timer when the air tempera-
ture is below 40℉(4.5℃), the timers should
be removed from the hose faucet and stored
indoors to avoid potential frozen damage.
Filter can trap dirt particles, please clean
filter regularly and replace if worn.
Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel cadmium) batteries.
Used up or dead batteries must be removed
from the timer and disposed of properly.
Please replace batteries when the low
battery indicator appears the display. When
replacing the power unit, please make sure
that the water timer is dry.
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries.
· Please do not insert rechargeable batteries to avoid
low voltage.
· The display will turn on for 3 seconds when power on.
Please make sure the timer is in Auto Run state.
1. Press the " " and Zone 1 have been select.
2. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 1. And Zone 2 have been select.
3. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 2.
Manual
· The timer don't have programmable
memory, it need to reset once power off.
1. Each program can only have one valve for watering.
2. If Z1 or Z2 is set to 00, the zone will not be watered.
Note:
6
Multi-Function
6. Precautions
4. Battery Installation
Note:
7. FAQ
Four batteries loaded are new 1.5V AA alkaline
batteries, make sure the batteries are properly placed
in the battery box. Do not use rechargeable batteries,
please you must use alkaline batteries.
A1:
Q1: The LCD screen does not display anything
when the batteries are installed.
Clock should be set to the correct time.
Start time is set to desired the time.
Rain Delay is on.
OFF mode is on.
The batteries are low.
The faucet is turned off.
A2:
Q2: Water does not come on at preset time.
Check if:
The O-ring is connected correctly to the hose tap.
The connection outlet or water pipe is broken.
The faucet and water pipe has a different thread.
If necessary, please use an appropriate adapter or
PTFE tape.
A3:
Q3: The hose tap connection/outlet leaks.
Check if:
If your are gravity feed system such as rain barrel system,
then it won't work and will keep low water pressure.
Gravity feed has no real pressure when dealing with a rain
barrel. It needs pressure measuring.
A4 :
Q4: Why is the water valve out of little water?
The timer have one year warranty, if you have any
questions, please feel free to contact via
The following conditions are not included in the warranty:
-Problems occur due to its use for other purposes, or
improper use or use of components not supplied by
Diivoo.
-Damages caused by improper use, for example, wrong of
power supply, artificial damage, etc.
8. After-sales Service
1
Inlet/Outlet Thread
Working Water Pressure
Working Temperature
Rain Delay Time
Waterproof
Included in the box
NH3/4"
7.25psi - 116psi
40.1˚ F-113˚ F
1 day and up to 7 days
IPX5
Watering Duration 00:01-23:59
5. Specification
· All Auto program are on hold during the rain delay.
If you want to cancel the Rain Delay, press " "
button 5s again.
· Rain delay allows you to postpone watering for 1
day and up to 7 days.
Note:
Please make sure the timer is in Auto Run state.
1. Hold and press " " button 5s until the appears
on the screen.
2. Press " " button to set the duration of the
delay from 1 to 7 days.
3. Press " " button it will start to watering.
Rain Delay
2
Please make sure the timer is in Auto Run state.
Hold and press " " button 5s until the " " appears
on the screen. If you want to cancel the " ", press
" " button 5s again.
Children Lock
3
1 x Water Timer,
2 x Threaded connector,
1 x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1 x Thread Seal Tape,
Instruction
When you press the " " button again, the manual
watering task ends even if it is watering and the timer
will switch back to Auto mode.
Do not use your timer when the air tempera-
ture is below 40℉(4.5℃), the timers should
be removed from the hose faucet and stored
indoors to avoid potential frozen damage.
Filter can trap dirt particles, please clean
filter regularly and replace if worn.
Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel cadmium) batteries.
Used up or dead batteries must be removed
from the timer and disposed of properly.
Please replace batteries when the low
battery indicator appears the display. When
replacing the power unit, please make sure
that the water timer is dry.
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries.
· Please do not insert rechargeable batteries to avoid
low voltage.
· The display will turn on for 3 seconds when power on.
Please make sure the timer is in Auto Run state.
1. Press the " " and Zone 1 have been select.
2. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 1. And Zone 2 have been select.
3. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 2.
Manual
· The timer don't have programmable
memory, it need to reset once power off.
1. Each program can only have one valve for watering.
2. If Z1 or Z2 is set to 00, the zone will not be watered.
Note:
6
Multi-Function
6. Precautions
4. Battery Installation
Note:
7. FAQ
Four batteries loaded are new 1.5V AA alkaline
batteries, make sure the batteries are properly placed
in the battery box. Do not use rechargeable batteries,
please you must use alkaline batteries.
A1:
Q1: The LCD screen does not display anything
when the batteries are installed.
Clock should be set to the correct time.
Start time is set to desired the time.
Rain Delay is on.
OFF mode is on.
The batteries are low.
The faucet is turned off.
A2:
Q2: Water does not come on at preset time.
Check if:
The O-ring is connected correctly to the hose tap.
The connection outlet or water pipe is broken.
The faucet and water pipe has a different thread.
If necessary, please use an appropriate adapter or
PTFE tape.
A3:
Q3: The hose tap connection/outlet leaks.
Check if:
If your are gravity feed system such as rain barrel system,
then it won't work and will keep low water pressure.
Gravity feed has no real pressure when dealing with a rain
barrel. It needs pressure measuring.
A4 :
Q4: Why is the water valve out of little water?
The timer have one year warranty, if you have any
questions, please feel free to contact via
The following conditions are not included in the warranty:
-Problems occur due to its use for other purposes, or
improper use or use of components not supplied by
Diivoo.
-Damages caused by improper use, for example, wrong of
power supply, artificial damage, etc.
8. After-sales Service
1
Inlet/Outlet Thread
Working Water Pressure
Working Temperature
Rain Delay Time
Waterproof
Included in the box
NH3/4"
7.25psi - 116psi
40.1˚ F-113˚ F
1 day and up to 7 days
IPX5
Watering Duration 00:01-23:59
5. Specification
· All Auto program are on hold during the rain delay.
If you want to cancel the Rain Delay, press " "
button 5s again.
· Rain delay allows you to postpone watering for 1
day and up to 7 days.
Note:
Please make sure the timer is in Auto Run state.
1. Hold and press " " button 5s until the appears
on the screen.
2. Press " " button to set the duration of the
delay from 1 to 7 days.
3. Press " " button it will start to watering.
Rain Delay
2
Please make sure the timer is in Auto Run state.
Hold and press " " button 5s until the " " appears
on the screen. If you want to cancel the " ", press
" " button 5s again.
Children Lock
3
1 x Water Timer,
2 x Threaded connector,
1 x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1 x Thread Seal Tape,
Instruction
When you press the " " button again, the manual
watering task ends even if it is watering and the timer
will switch back to Auto mode.
Do not use your timer when the air tempera-
ture is below 40℉(4.5℃), the timers should
be removed from the hose faucet and stored
indoors to avoid potential frozen damage.
Filter can trap dirt particles, please clean
filter regularly and replace if worn.
Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel cadmium) batteries.
Used up or dead batteries must be removed
from the timer and disposed of properly.
Please replace batteries when the low
battery indicator appears the display. When
replacing the power unit, please make sure
that the water timer is dry.
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries.
· Please do not insert rechargeable batteries to avoid
low voltage.
· The display will turn on for 3 seconds when power on.
Please make sure the timer is in Auto Run state.
1. Press the " " and Zone 1 have been select.
2. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 1. And Zone 2 have been select.
3. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 2.
Manual
· The timer don't have programmable
memory, it need to reset once power off.
1. Each program can only have one valve for watering.
2. If Z1 or Z2 is set to 00, the zone will not be watered.
Note:
6
Multi-Function
6. Precautions
4. Battery Installation
Note:
7. FAQ
Four batteries loaded are new 1.5V AA alkaline
batteries, make sure the batteries are properly placed
in the battery box. Do not use rechargeable batteries,
please you must use alkaline batteries.
A1:
Q1: The LCD screen does not display anything
when the batteries are installed.
Clock should be set to the correct time.
Start time is set to desired the time.
Rain Delay is on.
OFF mode is on.
The batteries are low.
The faucet is turned off.
A2:
Q2: Water does not come on at preset time.
Check if:
The O-ring is connected correctly to the hose tap.
The connection outlet or water pipe is broken.
The faucet and water pipe has a different thread.
If necessary, please use an appropriate adapter or
PTFE tape.
A3:
Q3: The hose tap connection/outlet leaks.
Check if:
If your are gravity feed system such as rain barrel system,
then it won't work and will keep low water pressure.
Gravity feed has no real pressure when dealing with a rain
barrel. It needs pressure measuring.
A4 :
Q4: Why is the water valve out of little water?
The timer have one year warranty, if you have any
questions, please feel free to contact via
The following conditions are not included in the warranty:
-Problems occur due to its use for other purposes, or
improper use or use of components not supplied by
Diivoo.
-Damages caused by improper use, for example, wrong of
power supply, artificial damage, etc.
8. After-sales Service
1
Inlet/Outlet Thread
Working Water Pressure
Working Temperature
Rain Delay Time
Waterproof
Included in the box
NH3/4"
7.25psi - 116psi
40.1˚ F-113˚ F
1 day and up to 7 days
IPX5
Watering Duration 00:01-23:59
5. Specification
· All Auto program are on hold during the rain delay.
If you want to cancel the Rain Delay, press " "
button 5s again.
· Rain delay allows you to postpone watering for 1
day and up to 7 days.
Note:
Please make sure the timer is in Auto Run state.
1. Hold and press " " button 5s until the appears
on the screen.
2. Press " " button to set the duration of the
delay from 1 to 7 days.
3. Press " " button it will start to watering.
Rain Delay
2
Please make sure the timer is in Auto Run state.
Hold and press " " button 5s until the " " appears
on the screen. If you want to cancel the " ", press
" " button 5s again.
Children Lock
3
1 x Water Timer,
2 x Threaded connector,
1 x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1 x Thread Seal Tape,
Instruction
When you press the " " button again, the manual
watering task ends even if it is watering and the timer
will switch back to Auto mode.
Do not use your timer when the air tempera-
ture is below 40℉(4.5℃), the timers should
be removed from the hose faucet and stored
indoors to avoid potential frozen damage.
Filter can trap dirt particles, please clean
filter regularly and replace if worn.
Do not mix alkaline, standard (carbon-zinc),
or rechargeable (nickel cadmium) batteries.
Used up or dead batteries must be removed
from the timer and disposed of properly.
Please replace batteries when the low
battery indicator appears the display. When
replacing the power unit, please make sure
that the water timer is dry.
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries.
· Please do not insert rechargeable batteries to avoid
low voltage.
· The display will turn on for 3 seconds when power on.
Please make sure the timer is in Auto Run state.
1. Press the " " and Zone 1 have been select.
2. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 1. And Zone 2 have been select.
3. Press " " to select watering duration from
1 min to 23 hours. Press" "to confirm the
setting of Zone 2.
Manual
· The timer don't have programmable
memory, it need to reset once power off.
1. Each program can only have one valve for watering.
2. If Z1 or Z2 is set to 00, the zone will not be watered.
Note:
6
Multi-Function
6. Precautions
4. Battery Installation
Note:
7. FAQ
Four batteries loaded are new 1.5V AA alkaline
batteries, make sure the batteries are properly placed
in the battery box. Do not use rechargeable batteries,
please you must use alkaline batteries.
A1:
Q1: The LCD screen does not display anything
when the batteries are installed.
Clock should be set to the correct time.
Start time is set to desired the time.
Rain Delay is on.
OFF mode is on.
The batteries are low.
The faucet is turned off.
A2:
Q2: Water does not come on at preset time.
Check if:
The O-ring is connected correctly to the hose tap.
The connection outlet or water pipe is broken.
The faucet and water pipe has a different thread.
If necessary, please use an appropriate adapter or
PTFE tape.
A3:
Q3: The hose tap connection/outlet leaks.
Check if:
If your are gravity feed system such as rain barrel system,
then it won't work and will keep low water pressure.
Gravity feed has no real pressure when dealing with a rain
barrel. It needs pressure measuring.
A4 :
Q4: Why is the water valve out of little water?
The timer have one year warranty, if you have any
questions, please feel free to contact via
The following conditions are not included in the warranty:
-Problems occur due to its use for other purposes, or
improper use or use of components not supplied by
Diivoo.
-Damages caused by improper use, for example, wrong of
power supply, artificial damage, etc.
8. After-sales Service
1
Inlet/Outlet Thread
Working Water Pressure
Working Temperature
Rain Delay Time
Waterproof
Included in the box
NH3/4"
7.25psi - 116psi
40.1˚ F-113˚ F
1 day and up to 7 days
IPX5
Watering Duration 00:01-23:59
5. Specification
· All Auto program are on hold during the rain delay.
If you want to cancel the Rain Delay, press " "
button 5s again.
· Rain delay allows you to postpone watering for 1
day and up to 7 days.
Note:
Please make sure the timer is in Auto Run state.
1. Hold and press " " button 5s until the appears
on the screen.
2. Press " " button to set the duration of the
delay from 1 to 7 days.
3. Press " " button it will start to watering.
Rain Delay
2
Please make sure the timer is in Auto Run state.
Hold and press " " button 5s until the " " appears
on the screen. If you want to cancel the " ", press
" " button 5s again.
Children Lock
3
1 x Water Timer,
2 x Threaded connector,
1 x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1 x Thread Seal Tape,
Instruction
Table of contents
Other Diivoo Timer manuals
