Diivoo WT-05 User manual

Diivoo
Bluetooth Dual Water Timer
TTT
WT-05
Need Help?
: [email protected]
Diivoo
Thank You
If you have any questions, please feel free to contact us firstly.
We are always here for you.
Pe
e The best range for connection and control is within
49.2ft in the open area.
e The bluetooth water timer does not support Alexa &
Google voice or remote control.
e Do not use your timer when the air temperature is
below 40*(4.5°C), the timers should be removed from
the hose faucet and stored indoors to avoid potential
frozen damage.
e Filter can trap dirt particles, please clean filter regularly
and replace if worn.
e Please replace batteries when the low battery indicator
appears the display. When replacing the power unit,
please make sure that the water timer is dry.
e To prevent leakage, make sure that the water timer is
tightly attached to the faucet and hose, add rubber
washer and thread seal tape if necessary.
Note:
(1) The water flow is reduced by half when the two zones
are turned on at the same time.
(2)The water flow in two zones may be different if you turn
on one zone first and then turn on the other zone.
PAM MM UT OM TE Cee ree as
Hose Faucet Connection
LED Light
ON/OFF Button
Outlet
Fitting NH3/4
Bluetooth Range 49.2ft without interference
Working Water Pressure | 7.25-116 psi
Working Temperature 40.1°F -113°F (4.5°C-45°C)
Rain Delay Time 1 day and up to 7 days
Waterproof IPX5
1x Water Timer,
2 x Threaded connector,
1x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1x Thread Seal Tape,
Included in the Box
Instruction
3. Initial Water Timer Setup
1 Insert Four AA Batteries
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries. Please do not
insert rechargeable batteries to avoid low voltage.
Note:
a.Do not mix alkaline, standard
(carbon-zinc), or rechargeable ¢
(nickel cadmium) batteries.
b.Used up or dead batteries
must be removed from the
timer and disposed of properly.
2 Install the Timer
Connect the timer to an outdoor hose faucet.
Your timer is now ready to be used with any product
that can be attached to a standard hose faucet.
Note:
Do not place the timer in an underground valve
box or anywhere your Bluetooth signal will be
obstructed.
3 Turn on Your Water 4 Add a Device
The water must remain on for the timer to work
properly.
Cm Cm eh
1 Download the Smart Life App
Tap "Add device" or "+" to add the smart device
in app. Select "Industry&Agriculture" > "Water
valve controller(BLE)".
Waiting for connecting to be 100%. Edit the
name of your water timer completed.
Scan the QR code and download the free Android or
Reset the device first.
10S
app,
then
install
the
APP.
If
you
have
already
=
|
Benen
©
|
installed
the
Smart
Life
APP,
go
to
step
2.
-—4
b
[hl
aE
=
an
@
App
Store
—
ae
ae
[=]
=
=a
2 _s Enter configuration Mode
Long press either of the "On/OFF button" for 6s until
the two green lights flash quickly at the same time to
keep the water timer in pairing mode.
Note:
Make sure Bluetooth on your phone is turned on sett
i
i
Battery
Life
etting
during paring.
Weather
Zone Jone zea Zone2
On/OFF
button
Custom
image
——+
Custom
image
Manual watering r x
Function Manual watering
Function
Work Time Work Time
Oh 10min Oh 10min
Schedule for Zone 1 — Schedule for Zone 2
3 Open the Smart Life App
Create an account or login with an existing account
to begin timer setup.

Diivoo
Bluetooth Dual Water Timer
TTT
WT-05
Need Help?
: [email protected]
Diivoo
Thank You
If you have any questions, please feel free to contact us firstly.
We are always here for you.
Pe
e The best range for connection and control is within
49.2ft in the open area.
e The bluetooth water timer does not support Alexa &
Google voice or remote control.
e Do not use your timer when the air temperature is
below 40*(4.5°C), the timers should be removed from
the hose faucet and stored indoors to avoid potential
frozen damage.
e Filter can trap dirt particles, please clean filter regularly
and replace if worn.
e Please replace batteries when the low battery indicator
appears the display. When replacing the power unit,
please make sure that the water timer is dry.
e To prevent leakage, make sure that the water timer is
tightly attached to the faucet and hose, add rubber
washer and thread seal tape if necessary.
Note:
(1) The water flow is reduced by half when the two zones
are turned on at the same time.
(2)The water flow in two zones may be different if you turn
on one zone first and then turn on the other zone.
PAM MM UT OM TE Cee ree as
Hose Faucet Connection
LED Light
ON/OFF Button
Outlet
Fitting NH3/4
Bluetooth Range 49.2ft without interference
Working Water Pressure | 7.25-116 psi
Working Temperature 40.1°F -113°F (4.5°C-45°C)
Rain Delay Time 1 day and up to 7 days
Waterproof IPX5
1x Water Timer,
2 x Threaded connector,
1x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1x Thread Seal Tape,
Included in the Box
Instruction
3. Initial Water Timer Setup
1 Insert Four AA Batteries
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries. Please do not
insert rechargeable batteries to avoid low voltage.
Note:
a.Do not mix alkaline, standard
(carbon-zinc), or rechargeable ¢
(nickel cadmium) batteries.
b.Used up or dead batteries
must be removed from the
timer and disposed of properly.
2 Install the Timer
Connect the timer to an outdoor hose faucet.
Your timer is now ready to be used with any product
that can be attached to a standard hose faucet.
Note:
Do not place the timer in an underground valve
box or anywhere your Bluetooth signal will be
obstructed.
3 Turn on Your Water 4 Add a Device
The water must remain on for the timer to work
properly.
Cm Cm eh
1 Download the Smart Life App
Tap "Add device" or "+" to add the smart device
in app. Select "Industry&Agriculture" > "Water
valve controller(BLE)".
Waiting for connecting to be 100%. Edit the
name of your water timer completed.
Scan the QR code and download the free Android or
Reset the device first.
10S
app,
then
install
the
APP.
If
you
have
already
=
|
Benen
©
|
installed
the
Smart
Life
APP,
go
to
step
2.
-—4
b
[hl
aE
=
an
@
App
Store
—
ae
ae
[=]
=
=a
2 _s Enter configuration Mode
Long press either of the "On/OFF button" for 6s until
the two green lights flash quickly at the same time to
keep the water timer in pairing mode.
Note:
Make sure Bluetooth on your phone is turned on sett
i
i
Battery
Life
etting
during paring.
Weather
Zone Jone zea Zone2
On/OFF
button
Custom
image
——+
Custom
image
Manual watering r x
Function Manual watering
Function
Work Time Work Time
Oh 10min Oh 10min
Schedule for Zone 1 — Schedule for Zone 2
3 Open the Smart Life App
Create an account or login with an existing account
to begin timer setup.

Diivoo
Bluetooth Dual Water Timer
TTT
WT-05
Need Help?
: [email protected]
Diivoo
Thank You
If you have any questions, please feel free to contact us firstly.
We are always here for you.
Pe
e The best range for connection and control is within
49.2ft in the open area.
e The bluetooth water timer does not support Alexa &
Google voice or remote control.
e Do not use your timer when the air temperature is
below 40*(4.5°C), the timers should be removed from
the hose faucet and stored indoors to avoid potential
frozen damage.
e Filter can trap dirt particles, please clean filter regularly
and replace if worn.
e Please replace batteries when the low battery indicator
appears the display. When replacing the power unit,
please make sure that the water timer is dry.
e To prevent leakage, make sure that the water timer is
tightly attached to the faucet and hose, add rubber
washer and thread seal tape if necessary.
Note:
(1) The water flow is reduced by half when the two zones
are turned on at the same time.
(2)The water flow in two zones may be different if you turn
on one zone first and then turn on the other zone.
PAM MM UT OM TE Cee ree as
Hose Faucet Connection
LED Light
ON/OFF Button
Outlet
Fitting NH3/4
Bluetooth Range 49.2ft without interference
Working Water Pressure | 7.25-116 psi
Working Temperature 40.1°F -113°F (4.5°C-45°C)
Rain Delay Time 1 day and up to 7 days
Waterproof IPX5
1x Water Timer,
2 x Threaded connector,
1x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1x Thread Seal Tape,
Included in the Box
Instruction
3. Initial Water Timer Setup
1 Insert Four AA Batteries
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries. Please do not
insert rechargeable batteries to avoid low voltage.
Note:
a.Do not mix alkaline, standard
(carbon-zinc), or rechargeable ¢
(nickel cadmium) batteries.
b.Used up or dead batteries
must be removed from the
timer and disposed of properly.
2 Install the Timer
Connect the timer to an outdoor hose faucet.
Your timer is now ready to be used with any product
that can be attached to a standard hose faucet.
Note:
Do not place the timer in an underground valve
box or anywhere your Bluetooth signal will be
obstructed.
3 Turn on Your Water 4 Add a Device
The water must remain on for the timer to work
properly.
Cm Cm eh
1 Download the Smart Life App
Tap "Add device" or "+" to add the smart device
in app. Select "Industry&Agriculture" > "Water
valve controller(BLE)".
Waiting for connecting to be 100%. Edit the
name of your water timer completed.
Scan the QR code and download the free Android or
Reset the device first.
10S
app,
then
install
the
APP.
If
you
have
already
=
|
Benen
©
|
installed
the
Smart
Life
APP,
go
to
step
2.
-—4
b
[hl
aE
=
an
@
App
Store
—
ae
ae
[=]
=
=a
2 _s Enter configuration Mode
Long press either of the "On/OFF button" for 6s until
the two green lights flash quickly at the same time to
keep the water timer in pairing mode.
Note:
Make sure Bluetooth on your phone is turned on sett
i
i
Battery
Life
etting
during paring.
Weather
Zone Jone zea Zone2
On/OFF
button
Custom
image
——+
Custom
image
Manual watering r x
Function Manual watering
Function
Work Time Work Time
Oh 10min Oh 10min
Schedule for Zone 1 — Schedule for Zone 2
3 Open the Smart Life App
Create an account or login with an existing account
to begin timer setup.

Diivoo
Bluetooth Dual Water Timer
TTT
WT-05
Need Help?
: [email protected]
Diivoo
Thank You
If you have any questions, please feel free to contact us firstly.
We are always here for you.
Pe
e The best range for connection and control is within
49.2ft in the open area.
e The bluetooth water timer does not support Alexa &
Google voice or remote control.
e Do not use your timer when the air temperature is
below 40*(4.5°C), the timers should be removed from
the hose faucet and stored indoors to avoid potential
frozen damage.
e Filter can trap dirt particles, please clean filter regularly
and replace if worn.
e Please replace batteries when the low battery indicator
appears the display. When replacing the power unit,
please make sure that the water timer is dry.
e To prevent leakage, make sure that the water timer is
tightly attached to the faucet and hose, add rubber
washer and thread seal tape if necessary.
Note:
(1) The water flow is reduced by half when the two zones
are turned on at the same time.
(2)The water flow in two zones may be different if you turn
on one zone first and then turn on the other zone.
PAM MM UT OM TE Cee ree as
Hose Faucet Connection
LED Light
ON/OFF Button
Outlet
Fitting NH3/4
Bluetooth Range 49.2ft without interference
Working Water Pressure | 7.25-116 psi
Working Temperature 40.1°F -113°F (4.5°C-45°C)
Rain Delay Time 1 day and up to 7 days
Waterproof IPX5
1x Water Timer,
2 x Threaded connector,
1x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1x Thread Seal Tape,
Included in the Box
Instruction
3. Initial Water Timer Setup
1 Insert Four AA Batteries
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries. Please do not
insert rechargeable batteries to avoid low voltage.
Note:
a.Do not mix alkaline, standard
(carbon-zinc), or rechargeable ¢
(nickel cadmium) batteries.
b.Used up or dead batteries
must be removed from the
timer and disposed of properly.
2 Install the Timer
Connect the timer to an outdoor hose faucet.
Your timer is now ready to be used with any product
that can be attached to a standard hose faucet.
Note:
Do not place the timer in an underground valve
box or anywhere your Bluetooth signal will be
obstructed.
3 Turn on Your Water 4 Add a Device
The water must remain on for the timer to work
properly.
Cm Cm eh
1 Download the Smart Life App
Tap "Add device" or "+" to add the smart device
in app. Select "Industry&Agriculture" > "Water
valve controller(BLE)".
Waiting for connecting to be 100%. Edit the
name of your water timer completed.
Scan the QR code and download the free Android or
Reset the device first.
10S
app,
then
install
the
APP.
If
you
have
already
=
|
Benen
©
|
installed
the
Smart
Life
APP,
go
to
step
2.
-—4
b
[hl
aE
=
an
@
App
Store
—
ae
ae
[=]
=
=a
2 _s Enter configuration Mode
Long press either of the "On/OFF button" for 6s until
the two green lights flash quickly at the same time to
keep the water timer in pairing mode.
Note:
Make sure Bluetooth on your phone is turned on sett
i
i
Battery
Life
etting
during paring.
Weather
Zone Jone zea Zone2
On/OFF
button
Custom
image
——+
Custom
image
Manual watering r x
Function Manual watering
Function
Work Time Work Time
Oh 10min Oh 10min
Schedule for Zone 1 — Schedule for Zone 2
3 Open the Smart Life App
Create an account or login with an existing account
to begin timer setup.

Diivoo
Bluetooth Dual Water Timer
TTT
WT-05
Need Help?
: [email protected]
Diivoo
Thank You
If you have any questions, please feel free to contact us firstly.
We are always here for you.
Pe
e The best range for connection and control is within
49.2ft in the open area.
e The bluetooth water timer does not support Alexa &
Google voice or remote control.
e Do not use your timer when the air temperature is
below 40*(4.5°C), the timers should be removed from
the hose faucet and stored indoors to avoid potential
frozen damage.
e Filter can trap dirt particles, please clean filter regularly
and replace if worn.
e Please replace batteries when the low battery indicator
appears the display. When replacing the power unit,
please make sure that the water timer is dry.
e To prevent leakage, make sure that the water timer is
tightly attached to the faucet and hose, add rubber
washer and thread seal tape if necessary.
Note:
(1) The water flow is reduced by half when the two zones
are turned on at the same time.
(2)The water flow in two zones may be different if you turn
on one zone first and then turn on the other zone.
PAM MM UT OM TE Cee ree as
Hose Faucet Connection
LED Light
ON/OFF Button
Outlet
Fitting NH3/4
Bluetooth Range 49.2ft without interference
Working Water Pressure | 7.25-116 psi
Working Temperature 40.1°F -113°F (4.5°C-45°C)
Rain Delay Time 1 day and up to 7 days
Waterproof IPX5
1x Water Timer,
2 x Threaded connector,
1x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1x Thread Seal Tape,
Included in the Box
Instruction
3. Initial Water Timer Setup
1 Insert Four AA Batteries
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries. Please do not
insert rechargeable batteries to avoid low voltage.
Note:
a.Do not mix alkaline, standard
(carbon-zinc), or rechargeable ¢
(nickel cadmium) batteries.
b.Used up or dead batteries
must be removed from the
timer and disposed of properly.
2 Install the Timer
Connect the timer to an outdoor hose faucet.
Your timer is now ready to be used with any product
that can be attached to a standard hose faucet.
Note:
Do not place the timer in an underground valve
box or anywhere your Bluetooth signal will be
obstructed.
3 Turn on Your Water 4 Add a Device
The water must remain on for the timer to work
properly.
Cm Cm eh
1 Download the Smart Life App
Tap "Add device" or "+" to add the smart device
in app. Select "Industry&Agriculture" > "Water
valve controller(BLE)".
Waiting for connecting to be 100%. Edit the
name of your water timer completed.
Scan the QR code and download the free Android or
Reset the device first.
10S
app,
then
install
the
APP.
If
you
have
already
=
|
Benen
©
|
installed
the
Smart
Life
APP,
go
to
step
2.
-—4
b
[hl
aE
=
an
@
App
Store
—
ae
ae
[=]
=
=a
2 _s Enter configuration Mode
Long press either of the "On/OFF button" for 6s until
the two green lights flash quickly at the same time to
keep the water timer in pairing mode.
Note:
Make sure Bluetooth on your phone is turned on sett
i
i
Battery
Life
etting
during paring.
Weather
Zone Jone zea Zone2
On/OFF
button
Custom
image
——+
Custom
image
Manual watering r x
Function Manual watering
Function
Work Time Work Time
Oh 10min Oh 10min
Schedule for Zone 1 — Schedule for Zone 2
3 Open the Smart Life App
Create an account or login with an existing account
to begin timer setup.

hedule Type Select Sche
o Normal Timing
oe @ Cycle Timing
@ Click the “Set time” and “+” button to add a watering
scheduel.
@ Two irrigation modes:
© Timed Watering Schedule: Water at a specific time.
At this mode, you can:
Select (Start time)to decide when you want the device
to start watering .
Select(Irrigation Duration)choose the time of day
you want to watering.
Select days of the week to decide which day or
days you want watering.
6 Cyclical Watering Schedule: Cycle watering within
the set start and end time. At this mode, you can:
Select (Start time)to decide when you want the device
to start watering and Select (End time)to stop watering.
Select days of the week to decide which day or days
you want watering.
(Interval Time) Set a interval time.
(Irrigation Duration) Determine how long to water.
Note: When setting the Cyclical Watering Schedule, the
Irrigation Duration plus Interval Time shall not exceed the
interval of the start time to end time
x Add Timed Watering Sc... x Add Cyclical Watering S...
Start Time End Time
AM 5 51 AM 1 50 6 48 AM
PM 2 51 7 ar PM
5 50
YF
Irrigation Duration f
~————————1 Bim Oui @@ >
@ Weekly cycte
Circulation unit
Tis
Odd day —S=—S
Irrigation Duration hémin
Even day Msi Time aassr|
Every few days
© Timed Watering Schedule © Cyclical Watering Schedule
Note: Timed Watering Schedule and Cyclical Watering
Schedule can be set 10 (max) for each, and 20 in total.
Odd day
Even day
Every few days
@ odd day: Water on odd days of the month (e.g. 1.3.5...)
e even day: Water on even days of the month (e.g. 2.4.6...)
e every few days: Interval watering time
- If you select every 2 days, mark watering
every other/second day (can be set to 1-31days)
Sun Mon Tue Wed Today Fri Sat
22°C 25°C 26°C 28°C 29°C 29°C 28°C
2% 19% 14 19°C 9%
= = = =
@ After setting the watering schedule, the watering
icon will be displayed under the weather icon.
Te Ca eee
1 Manual Watering
Your timer has the ability to allow you to manually
water without disturbing the programmed schedule.
Manual is used to test equipment, run an extra watering
cycle in an area, or to use the hose faucet without
removing the timer.
Click the ”. button to activate manual watering.
Using the app you can click *..’"” to set how long you
want manual watering time to run for the ”work time”,
also remaining watering time will be displayed.
2 Stop Watering
You can stop the flow of water at any time whether it is
during manual watering, or during a programmed time.
Click the * button once again to stop watering.
(NOTE: icon without water droplets)
3 Rain Delay Function
The rain delay function allows you to postpone
watering for 1 day and up to 7 days due to rain or
when the ground is already wet. Click the button to
activate manual watering. Using the app you can click
set how long you want the preset rain delay feature.
YPM |
Q1: Why the Bluetooth water timer didn't turn
on/off at preset time?
ap
@ Programming is incorrect
@ Water pressure is too low
@ Particles of dirt or debris stuck in valve
®@ More than one start time is programmed with
overlapping schedules
e@ Manual watering is on
e Faulty valve
@ The batteries were low
e@ The faucet is off.
Q2: Why Bluetooth keeps dropping connection?
ca
e The Bluetooth of water timer is currently in sleep
mode, please wait 5-10 seconds, the device will
automatically reconnect. Or scroll down to refresh
the home page of the APP, or disconnect the Bluetooth
from your phone and turn it on again
e If the device has been connected by other mobile
phones, please disconnect first.
e Make sure the device battery is charged and place the
phone as close to the device as possible.
e Please note that you don't need to stay connect once
you setup your schedule. The device will always keep
your watering settings and work automatically
according to the schedule.
Q3: Why is the water valve out of little water?
CED
If your are gravity feed system such as rain barrel
system, then it won't work and will keep low water
pressure. Gravity feed has no real pressure when
dealing with a rain barrel. It needs pressure
measuring.
MSY a
The timer have 1 year warranty since the day of
purchase. If you have any questions, please feel free
to contact via [email protected].
We will follow up and respond within 24 hours.
e The following conditions are not included:
Problems occur due to its use for other purposes,
or improper use or use of components not supplied
by Diivoo.
e Damages caused by improper use, for example,
wrong of power supply, artificial damage, etc.
FE ¥.CE OE
MADE IN CHINA

hedule Type Select Sche
o Normal Timing
oe @ Cycle Timing
@ Click the “Set time” and “+” button to add a watering
scheduel.
@ Two irrigation modes:
© Timed Watering Schedule: Water at a specific time.
At this mode, you can:
Select (Start time)to decide when you want the device
to start watering .
Select(Irrigation Duration)choose the time of day
you want to watering.
Select days of the week to decide which day or
days you want watering.
6 Cyclical Watering Schedule: Cycle watering within
the set start and end time. At this mode, you can:
Select (Start time)to decide when you want the device
to start watering and Select (End time)to stop watering.
Select days of the week to decide which day or days
you want watering.
(Interval Time) Set a interval time.
(Irrigation Duration) Determine how long to water.
Note: When setting the Cyclical Watering Schedule, the
Irrigation Duration plus Interval Time shall not exceed the
interval of the start time to end time
x Add Timed Watering Sc... x Add Cyclical Watering S...
Start Time End Time
AM 5 51 AM 1 50 6 48 AM
PM 2 51 7 ar PM
5 50
YF
Irrigation Duration f
~————————1 Bim Oui @@ >
@ Weekly cycte
Circulation unit
Tis
Odd day —S=—S
Irrigation Duration hémin
Even day Msi Time aassr|
Every few days
© Timed Watering Schedule © Cyclical Watering Schedule
Note: Timed Watering Schedule and Cyclical Watering
Schedule can be set 10 (max) for each, and 20 in total.
Odd day
Even day
Every few days
@ odd day: Water on odd days of the month (e.g. 1.3.5...)
e even day: Water on even days of the month (e.g. 2.4.6...)
e every few days: Interval watering time
- If you select every 2 days, mark watering
every other/second day (can be set to 1-31days)
Sun Mon Tue Wed Today Fri Sat
22°C 25°C 26°C 28°C 29°C 29°C 28°C
2% 19% 14 19°C 9%
= = = =
@ After setting the watering schedule, the watering
icon will be displayed under the weather icon.
Te Ca eee
1 Manual Watering
Your timer has the ability to allow you to manually
water without disturbing the programmed schedule.
Manual is used to test equipment, run an extra watering
cycle in an area, or to use the hose faucet without
removing the timer.
Click the ”. button to activate manual watering.
Using the app you can click *..’"” to set how long you
want manual watering time to run for the ”work time”,
also remaining watering time will be displayed.
2 Stop Watering
You can stop the flow of water at any time whether it is
during manual watering, or during a programmed time.
Click the * button once again to stop watering.
(NOTE: icon without water droplets)
3 Rain Delay Function
The rain delay function allows you to postpone
watering for 1 day and up to 7 days due to rain or
when the ground is already wet. Click the button to
activate manual watering. Using the app you can click
set how long you want the preset rain delay feature.
YPM |
Q1: Why the Bluetooth water timer didn't turn
on/off at preset time?
ap
@ Programming is incorrect
@ Water pressure is too low
@ Particles of dirt or debris stuck in valve
®@ More than one start time is programmed with
overlapping schedules
e@ Manual watering is on
e Faulty valve
@ The batteries were low
e@ The faucet is off.
Q2: Why Bluetooth keeps dropping connection?
ca
e The Bluetooth of water timer is currently in sleep
mode, please wait 5-10 seconds, the device will
automatically reconnect. Or scroll down to refresh
the home page of the APP, or disconnect the Bluetooth
from your phone and turn it on again
e If the device has been connected by other mobile
phones, please disconnect first.
e Make sure the device battery is charged and place the
phone as close to the device as possible.
e Please note that you don't need to stay connect once
you setup your schedule. The device will always keep
your watering settings and work automatically
according to the schedule.
Q3: Why is the water valve out of little water?
CED
If your are gravity feed system such as rain barrel
system, then it won't work and will keep low water
pressure. Gravity feed has no real pressure when
dealing with a rain barrel. It needs pressure
measuring.
MSY a
The timer have 1 year warranty since the day of
purchase. If you have any questions, please feel free
to contact via [email protected].
We will follow up and respond within 24 hours.
e The following conditions are not included:
Problems occur due to its use for other purposes,
or improper use or use of components not supplied
by Diivoo.
e Damages caused by improper use, for example,
wrong of power supply, artificial damage, etc.
FE ¥.CE OE
MADE IN CHINA

hedule Type Select Sche
o Normal Timing
oe @ Cycle Timing
@ Click the “Set time” and “+” button to add a watering
scheduel.
@ Two irrigation modes:
© Timed Watering Schedule: Water at a specific time.
At this mode, you can:
Select (Start time)to decide when you want the device
to start watering .
Select(Irrigation Duration)choose the time of day
you want to watering.
Select days of the week to decide which day or
days you want watering.
6 Cyclical Watering Schedule: Cycle watering within
the set start and end time. At this mode, you can:
Select (Start time)to decide when you want the device
to start watering and Select (End time)to stop watering.
Select days of the week to decide which day or days
you want watering.
(Interval Time) Set a interval time.
(Irrigation Duration) Determine how long to water.
Note: When setting the Cyclical Watering Schedule, the
Irrigation Duration plus Interval Time shall not exceed the
interval of the start time to end time
x Add Timed Watering Sc... x Add Cyclical Watering S...
Start Time End Time
AM 5 51 AM 1 50 6 48 AM
PM 2 51 7 ar PM
5 50
YF
Irrigation Duration f
~————————1 Bim Oui @@ >
@ Weekly cycte
Circulation unit
Tis
Odd day —S=—S
Irrigation Duration hémin
Even day Msi Time aassr|
Every few days
© Timed Watering Schedule © Cyclical Watering Schedule
Note: Timed Watering Schedule and Cyclical Watering
Schedule can be set 10 (max) for each, and 20 in total.
Odd day
Even day
Every few days
@ odd day: Water on odd days of the month (e.g. 1.3.5...)
e even day: Water on even days of the month (e.g. 2.4.6...)
e every few days: Interval watering time
- If you select every 2 days, mark watering
every other/second day (can be set to 1-31days)
Sun Mon Tue Wed Today Fri Sat
22°C 25°C 26°C 28°C 29°C 29°C 28°C
2% 19% 14 19°C 9%
= = = =
@ After setting the watering schedule, the watering
icon will be displayed under the weather icon.
Te Ca eee
1 Manual Watering
Your timer has the ability to allow you to manually
water without disturbing the programmed schedule.
Manual is used to test equipment, run an extra watering
cycle in an area, or to use the hose faucet without
removing the timer.
Click the ”. button to activate manual watering.
Using the app you can click *..’"” to set how long you
want manual watering time to run for the ”work time”,
also remaining watering time will be displayed.
2 Stop Watering
You can stop the flow of water at any time whether it is
during manual watering, or during a programmed time.
Click the * button once again to stop watering.
(NOTE: icon without water droplets)
3 Rain Delay Function
The rain delay function allows you to postpone
watering for 1 day and up to 7 days due to rain or
when the ground is already wet. Click the button to
activate manual watering. Using the app you can click
set how long you want the preset rain delay feature.
YPM |
Q1: Why the Bluetooth water timer didn't turn
on/off at preset time?
ap
@ Programming is incorrect
@ Water pressure is too low
@ Particles of dirt or debris stuck in valve
®@ More than one start time is programmed with
overlapping schedules
e@ Manual watering is on
e Faulty valve
@ The batteries were low
e@ The faucet is off.
Q2: Why Bluetooth keeps dropping connection?
ca
e The Bluetooth of water timer is currently in sleep
mode, please wait 5-10 seconds, the device will
automatically reconnect. Or scroll down to refresh
the home page of the APP, or disconnect the Bluetooth
from your phone and turn it on again
e If the device has been connected by other mobile
phones, please disconnect first.
e Make sure the device battery is charged and place the
phone as close to the device as possible.
e Please note that you don't need to stay connect once
you setup your schedule. The device will always keep
your watering settings and work automatically
according to the schedule.
Q3: Why is the water valve out of little water?
CED
If your are gravity feed system such as rain barrel
system, then it won't work and will keep low water
pressure. Gravity feed has no real pressure when
dealing with a rain barrel. It needs pressure
measuring.
MSY a
The timer have 1 year warranty since the day of
purchase. If you have any questions, please feel free
to contact via [email protected].
We will follow up and respond within 24 hours.
e The following conditions are not included:
Problems occur due to its use for other purposes,
or improper use or use of components not supplied
by Diivoo.
e Damages caused by improper use, for example,
wrong of power supply, artificial damage, etc.
FE ¥.CE OE
MADE IN CHINA

hedule Type Select Sche
o Normal Timing
oe @ Cycle Timing
@ Click the “Set time” and “+” button to add a watering
scheduel.
@ Two irrigation modes:
© Timed Watering Schedule: Water at a specific time.
At this mode, you can:
Select (Start time)to decide when you want the device
to start watering .
Select(Irrigation Duration)choose the time of day
you want to watering.
Select days of the week to decide which day or
days you want watering.
6 Cyclical Watering Schedule: Cycle watering within
the set start and end time. At this mode, you can:
Select (Start time)to decide when you want the device
to start watering and Select (End time)to stop watering.
Select days of the week to decide which day or days
you want watering.
(Interval Time) Set a interval time.
(Irrigation Duration) Determine how long to water.
Note: When setting the Cyclical Watering Schedule, the
Irrigation Duration plus Interval Time shall not exceed the
interval of the start time to end time
x Add Timed Watering Sc... x Add Cyclical Watering S...
Start Time End Time
AM 5 51 AM 1 50 6 48 AM
PM 2 51 7 ar PM
5 50
YF
Irrigation Duration f
~————————1 Bim Oui @@ >
@ Weekly cycte
Circulation unit
Tis
Odd day —S=—S
Irrigation Duration hémin
Even day Msi Time aassr|
Every few days
© Timed Watering Schedule © Cyclical Watering Schedule
Note: Timed Watering Schedule and Cyclical Watering
Schedule can be set 10 (max) for each, and 20 in total.
Odd day
Even day
Every few days
@ odd day: Water on odd days of the month (e.g. 1.3.5...)
e even day: Water on even days of the month (e.g. 2.4.6...)
e every few days: Interval watering time
- If you select every 2 days, mark watering
every other/second day (can be set to 1-31days)
Sun Mon Tue Wed Today Fri Sat
22°C 25°C 26°C 28°C 29°C 29°C 28°C
2% 19% 14 19°C 9%
= = = =
@ After setting the watering schedule, the watering
icon will be displayed under the weather icon.
Te Ca eee
1 Manual Watering
Your timer has the ability to allow you to manually
water without disturbing the programmed schedule.
Manual is used to test equipment, run an extra watering
cycle in an area, or to use the hose faucet without
removing the timer.
Click the ”. button to activate manual watering.
Using the app you can click *..’"” to set how long you
want manual watering time to run for the ”work time”,
also remaining watering time will be displayed.
2 Stop Watering
You can stop the flow of water at any time whether it is
during manual watering, or during a programmed time.
Click the * button once again to stop watering.
(NOTE: icon without water droplets)
3 Rain Delay Function
The rain delay function allows you to postpone
watering for 1 day and up to 7 days due to rain or
when the ground is already wet. Click the button to
activate manual watering. Using the app you can click
set how long you want the preset rain delay feature.
YPM |
Q1: Why the Bluetooth water timer didn't turn
on/off at preset time?
ap
@ Programming is incorrect
@ Water pressure is too low
@ Particles of dirt or debris stuck in valve
®@ More than one start time is programmed with
overlapping schedules
e@ Manual watering is on
e Faulty valve
@ The batteries were low
e@ The faucet is off.
Q2: Why Bluetooth keeps dropping connection?
ca
e The Bluetooth of water timer is currently in sleep
mode, please wait 5-10 seconds, the device will
automatically reconnect. Or scroll down to refresh
the home page of the APP, or disconnect the Bluetooth
from your phone and turn it on again
e If the device has been connected by other mobile
phones, please disconnect first.
e Make sure the device battery is charged and place the
phone as close to the device as possible.
e Please note that you don't need to stay connect once
you setup your schedule. The device will always keep
your watering settings and work automatically
according to the schedule.
Q3: Why is the water valve out of little water?
CED
If your are gravity feed system such as rain barrel
system, then it won't work and will keep low water
pressure. Gravity feed has no real pressure when
dealing with a rain barrel. It needs pressure
measuring.
MSY a
The timer have 1 year warranty since the day of
purchase. If you have any questions, please feel free
to contact via [email protected].
We will follow up and respond within 24 hours.
e The following conditions are not included:
Problems occur due to its use for other purposes,
or improper use or use of components not supplied
by Diivoo.
e Damages caused by improper use, for example,
wrong of power supply, artificial damage, etc.
FE ¥.CE OE
MADE IN CHINA

hedule Type Select Sche
o Normal Timing
oe @ Cycle Timing
@ Click the “Set time” and “+” button to add a watering
scheduel.
@ Two irrigation modes:
© Timed Watering Schedule: Water at a specific time.
At this mode, you can:
Select (Start time)to decide when you want the device
to start watering .
Select(Irrigation Duration)choose the time of day
you want to watering.
Select days of the week to decide which day or
days you want watering.
6 Cyclical Watering Schedule: Cycle watering within
the set start and end time. At this mode, you can:
Select (Start time)to decide when you want the device
to start watering and Select (End time)to stop watering.
Select days of the week to decide which day or days
you want watering.
(Interval Time) Set a interval time.
(Irrigation Duration) Determine how long to water.
Note: When setting the Cyclical Watering Schedule, the
Irrigation Duration plus Interval Time shall not exceed the
interval of the start time to end time
x Add Timed Watering Sc... x Add Cyclical Watering S...
Start Time End Time
AM 5 51 AM 1 50 6 48 AM
PM 2 51 7 ar PM
5 50
YF
Irrigation Duration f
~————————1 Bim Oui @@ >
@ Weekly cycte
Circulation unit
Tis
Odd day —S=—S
Irrigation Duration hémin
Even day Msi Time aassr|
Every few days
© Timed Watering Schedule © Cyclical Watering Schedule
Note: Timed Watering Schedule and Cyclical Watering
Schedule can be set 10 (max) for each, and 20 in total.
Odd day
Even day
Every few days
@ odd day: Water on odd days of the month (e.g. 1.3.5...)
e even day: Water on even days of the month (e.g. 2.4.6...)
e every few days: Interval watering time
- If you select every 2 days, mark watering
every other/second day (can be set to 1-31days)
Sun Mon Tue Wed Today Fri Sat
22°C 25°C 26°C 28°C 29°C 29°C 28°C
2% 19% 14 19°C 9%
= = = =
@ After setting the watering schedule, the watering
icon will be displayed under the weather icon.
Te Ca eee
1 Manual Watering
Your timer has the ability to allow you to manually
water without disturbing the programmed schedule.
Manual is used to test equipment, run an extra watering
cycle in an area, or to use the hose faucet without
removing the timer.
Click the ”. button to activate manual watering.
Using the app you can click *..’"” to set how long you
want manual watering time to run for the ”work time”,
also remaining watering time will be displayed.
2 Stop Watering
You can stop the flow of water at any time whether it is
during manual watering, or during a programmed time.
Click the * button once again to stop watering.
(NOTE: icon without water droplets)
3 Rain Delay Function
The rain delay function allows you to postpone
watering for 1 day and up to 7 days due to rain or
when the ground is already wet. Click the button to
activate manual watering. Using the app you can click
set how long you want the preset rain delay feature.
YPM |
Q1: Why the Bluetooth water timer didn't turn
on/off at preset time?
ap
@ Programming is incorrect
@ Water pressure is too low
@ Particles of dirt or debris stuck in valve
®@ More than one start time is programmed with
overlapping schedules
e@ Manual watering is on
e Faulty valve
@ The batteries were low
e@ The faucet is off.
Q2: Why Bluetooth keeps dropping connection?
ca
e The Bluetooth of water timer is currently in sleep
mode, please wait 5-10 seconds, the device will
automatically reconnect. Or scroll down to refresh
the home page of the APP, or disconnect the Bluetooth
from your phone and turn it on again
e If the device has been connected by other mobile
phones, please disconnect first.
e Make sure the device battery is charged and place the
phone as close to the device as possible.
e Please note that you don't need to stay connect once
you setup your schedule. The device will always keep
your watering settings and work automatically
according to the schedule.
Q3: Why is the water valve out of little water?
CED
If your are gravity feed system such as rain barrel
system, then it won't work and will keep low water
pressure. Gravity feed has no real pressure when
dealing with a rain barrel. It needs pressure
measuring.
MSY a
The timer have 1 year warranty since the day of
purchase. If you have any questions, please feel free
to contact via [email protected].
We will follow up and respond within 24 hours.
e The following conditions are not included:
Problems occur due to its use for other purposes,
or improper use or use of components not supplied
by Diivoo.
e Damages caused by improper use, for example,
wrong of power supply, artificial damage, etc.
FE ¥.CE OE
MADE IN CHINA