Timeguard TGBT6 Boostmaster User manual

Installation & Operating Instructions
HELPLINE
020 8450 0515
Electronic Plug-In
Boost Timer
Model No. TGBT6

1
2
1hr
2hr
1/2
1/4
Boost
Boost time LED’s
Boost Button
1. General Information
Contents
1 TGBT6 Boostmaster.
1 Instruction leaflet.
The TGBT6 is a plug-in boost timer giving a range of boost times from
1/4hr to 2hrs covering the majority of requirements for heating,
ventilation and lighting.
The unit plugs into a 13A socket.
It can be instantly cancelled or reset and the 1/4hr LED flashes
a warning of time out.
Fig. 1
TGBT6 Front

2
3
2. Operation
Plug the TGBT6 into a 13A socket and plug the load into the TGBT6.
The required boost time is selected by pressing the button marked
Boost repeatedly. The LED’s adjacent to the time markers (above the
Boost button) will light up in the sequence:-
First push gives 1/4hr boost (LED opposite 1/4 is on)
Second push gives 1/2hr boost (LED’s opposite 1/4 and 1/2 are on)
Third push gives 1hr boost (LED’s opposite 1/4, 1/2 and 1 are on)
Fourth push gives 2hr boost (LED’s opposite 1/4, 1/2, 1 and 2 are on)
Fifth push returns to zero boost (all LED’s out)
Once the boost selected is underway the LED’s will go out sequentially
indicating the approximate boost time remaining. The LED which is
about to go out will flash when there is less than 2 minutes remaining
of that period.
Example:- 2hr boost has been set.
After 1hr the 2hr LED will go out indicating 1hr remaining.
After a further 1/2hr the 1hr LED will go out indicating 1/2hr remaining.
After a further 1/4hr the 1/2hr LED will go out indicating
1/4hr remaining.
In this way the user has an approximate guide to the remaining
duration of the boost.

3
If it is less than 15 seconds since the Boost button was pressed the
boost may be stopped at any time by pressing the Boost button
repeatedly until all the LED’s are extinguished. After 15 seconds the
boost may be stopped by a single press of the Boost button.
The boost period may be changed at any time by pressing the Boost
button until the required time LED is lit. In which case the indicated
boost time will start from when the Boost button was pressed.
If the button is pressed and then held the LED’s will cycle upwards
with 1 second between each change. It will go in the sequence
1/4, 1/2, 1, 2, OFF, 1/4, 1/2 etc.
Stopping or Increasing Boost

4
HELPLINE
020 8450 0515
4. Specifications
EC Directives: Conforms to latest directives
and relevant clauses of the
following standards: BS EN 60730-7-2;
Particular requirements.
Timers and time switches.
Permissible loads: 13A resistive.
5A inductive.
1000W filament lamps.
500W fluorescent lighting.
100W low energy lamps.
For other loads refer to technical service
on 020-8450-0515.
Operating ambient temperature: 0 to +40ºC.
Operating voltage: 230VAC, 50Hz.
Boost times: 1/4hr, 1/2hr, 1hr, 2hr.
Size: 103mm L x 58mm W x 46mm D.
In the unlikely event of this product becoming faulty due to defective
material or manufacture, within 3 years of the date of purchase, please
return it to your supplier in the first year with proof of purchase
and it will be replaced free of charge. For years 2 and 3 or any difficulty
in the first year telephone our helpline on 020 8450 0515.
Note: A proof of purchase is required in all cases. For all eligible
replacements (where agreed by Timeguard) the customer is responsible
for all shipping/postal charges outside of the UK. All shipping costs
are to be paid in advance before a replacement is sent.
3 Year Guarantee

Zerofour – June 2015
67-058-385 (Issue 2)
Timeguard Limited.
Victory Park, 400 Edgware Road,
London NW2 6ND
Sales Office: 020 8452 1112
or email [e-mail]
For a product brochure please contact:
For assistance with the product please contact:
HELPLINE
020 8450 0515
or email [e-mail]
www.timeguard.com
4. Specifications