DIODE LED TOUCHDIAL DI-RF-REM-TW-4 Instruction sheet

DRY LOCATION
1 OF 2 IG122019-4.0
TOUCHDIAL
™
Remote INSTALLATION GUIDE
®
ADJUSTABLE KELVIN
INSTALLATION GUIDE
TOUCHDIAL™TUNABLE WHITE
4-Zone Remote Control
1. This product is rated for indoor installaon and is not protected
against moisture.
2. Do not modify product beyond instrucons or warranty will be void.
SAFETY & WARNINGS
QUICK SPECS / MODELS
TOOLS FOR INSTALL
Phillips-head screwdriver
(For mounng TOUCHDIAL Remote Control Mounng Bracket)
SYNCING INSTRUCTIONS
1
Input Operang Frequency
3x AAA 1.5V Baeries
(Not Included) 434MHz / 868 MHz
2
INSTALL TOUCHDIAL RECEIVER SYSTEM
TOUCHDIAL WiFi Hub: DI-WIFI-RF-TRMS
1. 5VDC Adapter
2. 75in. CAT5 / RJ45 Cable
LED Driver TOUCHDIAL Receiver LED Luminaire
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
MASTER COMPANION
DATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNINGKEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
V+
V−
L
N
GND
ADDITIONAL TOUCHDIAL COMPONENTS
DI-RF-REM-TW-4
DI-RF-REC-CV-A
TOUCHDIAL Receiver
DI-WIFI-RF-TRMS
TOUCHDIAL WiFi Hub
SYNC MASTER RECEIVER TO TOUCHDIAL CONTROL
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
D
ATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER
COMPANION
d. Luminaire will ash to indicate pairing.
a. Wake up TOUCHDIAL control by pressing
Power buon. A red light will indicate
remote is turned on.
®
S1 S2 S3
W+
1 2 3 4
b. Short press LEARNING
KEY buon on TOUCHDIAL
MASTER receiver.
®
S1 S2 S3
W+
1 2 3 4
c. (1) Press any zone buon on
control, then (2) swipe nger on
color wheel.
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
DATAIN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUTTO LOAD
POWER
INPUT
LEARNINGKEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER COMPANION
SUPPLIED ACCESSORIES
TOUCHDIAL Remote Control Mounng Bracket
Refer to TOUCHDIAL Receiver Installaon Guide.
®
S1 S2 S3
W+
1 2 3 4
Add 3x AAA baeries (not included).

2 OF 2
®Toll Free: 877.817.6028 | Fax: [phone] | www.DiodeLED.com | [e-mail]
© 2019 Elemental LED Inc. All rights reserved. Specicaons are subject to change without noce.
IG122019-4.0TOUCHDIAL
™
Remote INSTALLATION GUIDE
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
D
ATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER
COMPANION
SYNCING CONT.
Jumper
Header
COMPANION MASTER
SYNCING NOTE
When syncing the TOUCHDIAL Remote, the 1st receiver must be
set to the MASTER funcon as outlined below. See the TOUCHDIAL
Receiver Installaon Guide for more thorough informaon.
Symptom Common Cause
Remote won’t funcon
• Check for dead AAA baeries.
• Remote must be turned on for
operaon (red indicator light on).
Master receiver does not
sync with remote
• Ensure funcon is set to MASTER (1
pin) - See Syncing Note or TOUCHDIAL
Receiver Installaon Guide.
• If sll not syncing do following: 1)
Turn o main power to receiver and
turn back on. 2) Reset receiver by long
pressing LEARNING KEY for 5 seconds
unl LED ashes. 3) Re-sync receiver
to control.
TROUBLESHOOTING
Visit the product web page at www.DiodeLED.com for addional product specicaons & warranty informaon.
TOUCHDIAL TUNABLE WHITE REMOTE CONTROL SPECIFICATION SHEET
For full specicaons.
TOUCHDIAL RECEIVER SPECIFICATION SHEET & INSTALL GUIDE
For full specicaons and installaon instrucons.
TOUCHDIAL WIFI HUB SPECIFICATION SHEET & INSTALL GUIDE
For full specicaons and installaon instrucons.
ADDITIONAL RESOURCES
OPERATION
See TOUCHDIAL Receiver and WIFI Hub Install Guide for more
troubleshoong ps.