DIODE LED TOUCHDIAL User manual

COLOR-CHANGING
DRY LOCATION
1 OF 3 IG070319-2.0
TOUCHDIAL
™
Mini Remote RGB(W) Control INSTALL GUIDE
®
24VDC
12VDC
TOUCHDIAL™Mini Remote RGB(W) Control
INSTALLATION GUIDE
1. Only for use with compatible 12V and 24VDC constant voltage
luminaires.
2. This product is rated for indoor installation and is not protected
against moisture.
3. Do not modify product beyond instructions or warranty will be
void.
SAFETY & WARNINGS
QUICK SPECS / MODELS
DI-RF-REM-RGBW-1
FRONT BACK
APPROVED LED LUMINAIRES
The TOUCHDIAL Mini Remote RGB(W) Control is compatible
with all Diode LED 12V and 24VDC color constant voltage tape
lights and xtures.
Input Operating Frequency Dimensions
3V (CR2430)
Battery (Included) 869.5/434MHz 2.16 x 2.16 x 0.43 in. (L x W x H)
RGB
W
CR2430
Baery
ADDITIONAL TOUCHDIAL COMPONENTS
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
DATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT
TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER COMPANION
DI-RF-REC-CV-A
TOUCHDIAL Receiver
(Required)
RGB
W

2 OF 3 IG070319-2.0
TOUCHDIAL
™
Mini Remote RGB(W) Control INSTALL GUIDE
TOUCHDIAL™Mini Remote RGB(W) Control
INSTALLATION GUIDE
RGB
W
RGB
W
RGB
W
SYNCING INSTRUCTIONS
INSTALL TOUCHDIAL RECEIVER SYSTEM
LED Driver TOUCHDIAL Receiver LED Luminaire
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
MASTER COMPANION
DATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT
TO LOAD
POWER
INPUT
LEARNINGKEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
V+
V−
L
N
GND
SYNC TOUCHDIAL CONTROL TO MASTER
RECEIVER
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
D
ATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER
COMPANION
Short press Mini Remote
RGB(W) Control Power
button.
Short press LEARNING
KEY button on TOUCHDIAL
MASTER receiver.
Short press the Increase
Brightness button on the Mini
Remote RGB(W) Control.
Refer to TOUCHDIAL Receiver Installation Guide.
Luminaire will ash to indicate
pairing.
OPERATION
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
D
ATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER
COMPANION
SYNCING CONT.
Jumper
Header
COMPANION MASTER
SYNCING NOTE
When syncing the TOUCHDIAL Mini Remote RGB(W)
Control, the 1st receiver must be set to the MASTER
function as outlined below. See the TOUCHDIAL Receiver
Installation Guide for more thorough information.
Short press to turn
ON/OFF.
LOOKING FOR SYSTEM DIAGRAMS?
See the TOUCHDIAL RECEIVER (DI-RF-REC-CV-A)
Installation guide for SOLID COLOR system diagrams.
V−
V+
V+
W
B
G
R
®
TOUCHDIAL™ Receiver
DATA IN/OUT
V−
D1+
GND
V+
V+
V+
OUTPUT
TO LOAD
POWER
INPUT
LEARNING KEY
WW
WW
CW
CW
W
W
W
W
D1─
D2+
D2─
MASTER COMPANION
Long Press to
change RGB Color
selected.
Hold to increase
brightness.
Hold to increase
or decrease
White brightness
only.
Hold to decrease
brightness.
1
2
2.1
2.2
2.3
2.4

3 OF 3
®Toll Free: 877.817.6028 | Fax: [phone] | www.DiodeLED.com | [e-mail]
© 2019 Elemental LED, Inc. All rights reserved. Specicaons are subject to change without noce.
IG070319-2.0TOUCHDIAL
™
Mini Remote RGB(W) Control INSTALL GUIDE
TOUCHDIAL™Mini Remote Dimmer
INSTALLATION GUIDE
Symptom Common Cause
Control won’t
function
• Check for dead batteries.
• Remote must be turned on for
operation.
Master receiver does
not sync with remote
• Ensure function is set to MASTER
(1 pin) - See Syncing Note or
TOUCHDIAL Receiver Installation
Guide.
• If still not syncing do following: 1)
Turn off main power to receiver and
turn back on. 2) Reset receiver by
long pressing LEARNING KEY for
5 seconds until LED ashes. 3) Re-
sync receiver to control.
TROUBLESHOOTING
See TOUCHDIAL Receiver Install Guide for more troubleshooting tips.
BATTERY REPLACEMENT
1. Open Battery backplate on Remote.
2. Insert new battery.
TOUCHDIAL MINI REMOTE RGB(W) CONTROL
SPEC SHEET
For full specications.
TOUCHDIAL RECEIVER SPEC SHEET & INSTALL
GUIDE
For full specications and installation instructions.
ADDITIONAL RESOURCES
CR2430
Baery
MOUNTING
Metal Mounng Plate
RGB
W
1. Place Metal Mounting Plate on surface where desired, using
included 3M Mounting Tape Pad.
2. Place Mini Remote onto Mounting Plate. The Magnet inside
Mini Remote will hold it in place.