Directed Xpresskit DBALL2 User manual

®Hyundai is a registered trademark and property of its y.respective compan
Important!
This product is compatible with vehicles equipped with a manual transmission.NOT
Remote Start Ready ( ) is a function that enables the interface module to remote start the vehicleRSR
completely on its own. Consequently, there is no need for an aftermarket or an remote starter in order toOEM
start the vehicle from a distance.
SmartStart Compatible
SmartStart is equipped with D2D which means it can be connected to an interface module and used in, Remote
Start Ready ( ) mode the use of See the section for moreRSR without a remote starter. Module Programming
information.
Installation Guide
Update Alert: Firmware updates are posted the web on a regular basis. We recommendon
that you check for firmware and/or install guide updates prior to installing this product.
Index
This guide supports the installation of a 2 in Remote Start Ready ( ) mode. This solutionDBALL RSR
offers configuration options to control your system: RFthree (3) 3x Lock Remote Start Activation,OEM
Kit or SmartStart ( sold separately).both
Vehicle Application Guide ....... .................. ..................................... ............................... ......................................................
Installation s s(Wiring Diagram & Vehicle Wiring Reference Chart )
Type 1.............. ..... .................................................................................................................... ..........................................
Type .............. ..... ..........................................2 .......................................................................... ..........................................
Programming
Notes..................................................................................................................................................................................
Module Programming ...................... .............................................................................. .......... ...........................................
Module Reset.. ...................................................................................................................................................................
Hard ... ....Reset.. ................................................................................................................................................................
Feature & Option List..........................................................................................................................................................
Feature Programming.........................................................................................................................................................
LED Diagnostics & Troubleshooting...................................................................................................................................
Parking Lightg Error Codes................................................................................................................................................
Limited One-Year Consumer ........Warranty.......................................................................................................................
Quick Reference Guide......................................................................................................................................................
02
03
05
07
08
09
09
10
11
12
14
15
16
Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.

The table below lists the vehicles and features which are compatible with this product. Refer to the following pages for
more information on installation wiring, programming and troubleshooting for these vehicles.
Vehicle Application Guide Page 2
Vehicles
2017
2016
2015
2014
2013
PK-Immobilizer Bypass-Data No Key Req'd
AV-Panic Mode Activation
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
DL-Trunk / Hatch Release
RS-3x LOCK START (Start control using OEM Remote)
RS-3x LOCK STOP (Stop control using OEM Remote)
RS-Remote Start Ready
RS-SmartStart
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
ST-Brake Status (foot brake)
ST-Ignition Status
Hyundai
SantaFe(SmartKey) 22111 ••••••••••••••••••
SantaFeSport(SmartKey)22111 ••••••••••••••••••
Legend:
D: Data-to-Data (D2D) PK: Transponder & Immobilizer Override
•: D2D & Wire-to-Wire (W2W) AV: Horn & Lights Controls
DL: OE Door Lock & Alarm Controls
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.

Refer to the Vehicle Wiring Reference Chart on page for wire color and component location.4
Hood Pin
Remote Start Safety
Override Switch
You can connect to either a 202XL
RFTD a SmartStart module.OR
Refer to the SmartStart/ 202XL
Installation Notes for more information.
HS CAN High: 3Tan/Black:
FT CAN High: 5Orange/Green:
(+) Ignition : 8Output Yellow:
(+) 12V : 13Input Red:
HS CAN Low: 4Tan:
FT CAN Low: 6Orange/Brown:
(+) 12V Input: 7Brown:
(-) Ground: 14Black:
6: White/Black: (-) Hood Input
(-) 2 : 2PTS Output Green/Black:
(-) 1 : 1PTS Output Black/White:
(-) Parking Lights : 4Output Red/Black:
(+) Accessory Output: 6Gray:
(+) Starter Output: 7Gray/Black:
Immo. Data: 11Orange/Black:
C- LowCAN :
Orange, in 1p4
(+) 12V:
Gray/Black,
in 16p
EMS COM:
p32White/Orange,in
C- HighCAN :
Green,inp6
EM11
(black conn. in driver kick panel)
Note: hood pin only required
on vehicle not equipped with as
factory hood pin
46
26
11
43
33
18
8
36
21
1
45
35
25
20
10
44
34
24
19
9
3
12
22
27
37
13
23
28
38
2
32
39 40
41
42
29 30 31
14 15 16 17
4567
(+) Ignition:
pGreen, in 21
(+) Accessory:
p3Yellow, in
(-) Parking Lights:
Pink,5pin 1
16
15
14
13
12
11
10
876
5
4
3
2
1
9
M01-L
(white conn. at l s )head ight witch
8
16
OB IID
Diagnostic
connector
1
9
B- High:CAN
Blue, pin 24
1
11
21
39
9 8 76
5
4
3
2
1918
17
1615
14
13
12
2928
27
2625
24
23
22
3837363534333231
47
46
45
44
43
4241
40
10
20
30
48
11MF
(white conn. in driver kick panel)
B- Low:CAN
Red, pin 33
(+) Starter:
pPink, in 11
11 9101213141516
145 8
3
(-) PTS 1:
Orange/Black, pin 3
M04
(atblack conn.
switch)PTS
2
(-) PTS 2:
Yellow/Orange,
2pin
67
Page 3
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OB IIDs
Installation Type 1
10
2DBALL
RF
Prog Button.
LED
4
14 12 2
Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.

Page 4
Type - Vehicle Wiring Reference Chart1
Function Color Pin Polarity Location Color Pin
12V Red 1 (+) I/P-B, front of dash fuse box. White 4
PTS 1 Orange/Black 3 (-) M04, PTS switch. Black 12
PTS 2 Yellow/Orange 2 (-) M04, PTS switch. Black 12
C-CAN High Green 6 Data OBDII. Black 16
C-CAN Low Orange 14 Data OBDII. Black 16
Parking Lights
Pink 15 (-) M01-L, headlight switch. White 16
Starter Pink 11 (+) EM11, driver kick panel. Black 46
Ignition Green 21 (+) EM11, driver kick panel. Black 46
Accessory Yellow 3 (+) EM11, driver kick panel. Black 46
EMS COM White/Orange 32 Data EM11, driver kick panel. Black 46
B-CAN High Blue 24 Data MF11, driver kick panel. White 48
B-CAN Low Red 33 Data MF11, driver kick panel. White 48
12V Red 1 (+) I/P-B, front of dash fuse box. White 4
PTS 1 Orange/Black 3 (-) M04, PTS switch. Black 12
PTS 2 Yellow/Orange 2 (-) M04, PTS switch. Black 12
C-CAN High Green 6 Data OBDII. Black 16
C-CAN Low Orange 14 Data OBDII. Black 16
Parking Lights
Pink 15 (-) M01-L, headlight switch. White 16
Starter Pink 11 (+) EM11, driver kick panel. Black 46
Ignition Green 21 (+) EM11, driver kick panel. Black 46
Accessory Yellow 3 (+) EM11, driver kick panel. Black 46
EMS COM White/Orange 32 Data EM11, driver kick panel. Black 46
B-CAN High Blue 24 Data MF11, driver kick panel. White 48
B-CAN Low Red 33 Data MF11, driver kick panel. White 48
Wire Information
Connector Information
Santa Fe (Smart Key) 2013-2015
SantaFeSport(SmartKey)2013-2015
Driver Kick Panel
Locating components in the vehicle
Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.

Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.
Refer to the Vehicle Wiring Reference hartC on page 6 for wire color and component location.
Hood Pin
Remote Start Safety
Override Switch
You can connect to either a 202XL
RFTD a SmartStart module.OR
Refer to the SmartStart/ 202XL
Installation Notes for more information.
HS CAN High: 3Tan/Black:
FT CAN High: 5Orange/Green:
(+) Ignition : 8Output Yellow:
(+) 12V : 13Input Red:
HS CAN Low: 4Tan:
FT CAN Low: 6Orange/Brown:
(-) Ground: 14Black:
6: White/Black: (-) Hood Input
(-) : 2PTS 2 Output Green/Black:
(-) :PTS 1 Output 1Black White/:
(-) Parking Lights : 4Output Red/Black:
(+) Accessory Output: 6Gray:
(+) Starter Output: 7Gray/Black:
Immo. Data: 11Orange/Black:
C- LowCAN :
Orange, in 1p4
C- HighCAN :
Green,inp6
Note: hood pin only required
on vehicle not equipped with as
factory hood pin
(-) Parking Lights:
Pink,5pin 1
16
15
14
13
12
11
10
876
5
4
3
2
1
9
8
16
OB IID
Diagnostic
connector
1
9
(+) Starter:
pPink, in 7
EMS COM:
White/Orange,
in 6p3
48 58
7
25
11
(+) Ignition:
pGreen, in 25
(+) Accessory:
p19Yellow,in
36
35 20 41
5
42
6
43 21
44 37 30 22 55 57
34
29 19
40
4
38 27
2
39 28
3
EM11
(Red or White conn. in driver kick panel)
M01-L
(white conn. at light switch)head
B- Low 39CAN : pinRed,
B- HighCAN :
Blue,29pin
MF11
(inwhite conn.
driver k pick anel)
29 39
11 9101213141516
145 8
3
(-) PTS 1:
Orange/Black, pin 3
M04
(atblack conn.
switch)PTS
2
(-) PTS 2:
Yellow/Orange,
2pin
67
(+) 12V:
Gray/Black,
in 16p
(+) 12V Input: 7Brown:
With the exception of the Diagno tic connector, all adapters are displayed from the wire side (unless specified otherwise).OB IIDs
10
2DBALL
RF
Prog Button.
LED
4
14 12 2
Page 5
Installation Type 2

Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.
Page 6
Type - Vehicle Wiring Reference Chart2
Driver Kick Panel
Locating components in the vehicle
Function Color Pin
Polarity
Location Color Pin
12V Red 1 (+) EM31, drivers kick panel. White 1
PTS1 Orange/Black 3 (-) M04,PTSswitch. Black 12
PTS2 Yellow/Orange 2 (-) M04,PTSswitch. Black 12
C-CAN High Green 6 Data OBDII. Black 16
C-CAN Low Orange 14 Data OBDII. Black 16
Parking Lights
Pink 15 (-) M01-L,headlight switch. White 16
Starter Pink 7 (+) EM11, driver kick panel. Red or White 58
Ignition Green 25 (+) EM11, driver kick panel. Red or White 58
Accessory Yellow 19 (+) EM11, driver kick panel. Red or White 58
EMS COM White/Orange 36 Data EM11, driver kick panel. Red or White 58
B-CAN High Blue 29 Data MF11, driver kick panel. White 68
B-CAN Low Red 39 Data MF11, driver kick panel. White 68
12V Red 1 (+) EM31, drivers kick panel. White 1
PTS1 Orange/Black 3 (-) M04,PTSswitch. Black 12
PTS2 Yellow/Orange 2 (-) M04,PTSswitch. Black 12
C-CAN High Green 6 Data OBDII. Black 16
C-CAN Low Orange 14 Data OBDII. Black 16
Parking Lights
Pink 15 (-) M01-L, headlight switch. White 16
Starter Pink 7 (+) EM11, driver kick panel. Red or White 58
Ignition Green 25 (+) EM11, driver kick panel. Red or White 58
Accessory Yellow 19 (+) EM11, driver kick panel. Red or White 58
EMS COM White/Orange 19 Data EM11, driver kick panel. Red or White 58
B-CAN High Blue 29 Data MF11, driver kick panel. White 68
B-CAN Low Red 39 Data MF11, driver kick panel. White 68
Wire Information
Connector Information
Santa Fe (Smart Key) 2016-2017
Santa Fe Sport (Smart Key) 2016-2017

The 202 and antenna are not included and be purchased separately.optional XL MUST
Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE
4
4
XL202
Antenna
XOVER
SmartStart is and not included. It be purchased separately.optional MUST
SmartStart is and not included. It be purchased separately.optional MUST
Th 2 solution offers three (3) 3xe Remote Start Ready ( )DBALL RSR OEMconfiguration options to control your system:
Lock Remote Start Activation, . This section provides specific installationRF allKit or SmartStart ( sold separately)
information for SmartStart and 202.XL
Configuration Wires (Gray & White)
Connect Gray wire to (-) Ground
5 pins
D2D (4 pins, white)
4 pins
2 pins,
not used
CABLE
CABLE
The modules must be connected in a specific order. Refer to the section for more information.Module Programming
1. Use the D2D Crossover ( ) cable that is provided with 202, and the one in the package.XOVER XL NOT DBALL
2. The modules must be connected in a specific order. Refer to the section for more information.Module Programming
The modules must be connected in a specific order. Refer to the section for more information.Module Programming
SmartStart/ 202 Installation NotesXL
SmartStart Revision B
RF Kit
RF PKE& CombinationKit
Refer to the Passive Keyless Entry ( ) Installation Guide (N2102T) for detailed wiring information.PKE
RF PKE BT, & SmartStart CombinationKit
SmartStart Revision A
2DBALL
2DBALL
2DBALL
LED
Prog.
Button
D2D (4 pins, white)
4 pins
2 pins,
not used
OR
SmartStart
Configuration Wires (White & Brown or Blue)
Cut Brown or Blue Loop
LED
THIS SIDE UP
LED
Page 7
Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.

41X ENGINE
START
STOP
PUSH
Press the Push-to-Start (PTS) button more to turn the ignition OFF.once
You have successfully completed the programming sequence.module
Module Programming
Important
Page 8
1
10-pin
D2D
1st
12-pin
14-pin
2nd
3rd &
Solid
Connect the 10-pin 2-pin harnesses to, 1 and 14-pin
DBALL, then w .ait until the turns solid redLED ON
10-pin
D2D
XL202
10-pin
D2D
SmartStart
OR
The module be disconnected from any power source before SmartStart canDBALL must
be connected to it. Failing to do so could damage .2DBALL
a. To ensure that the D2D communication between SmartStart and works properly, theDBALL
Gray wire must be connected to a ground source ( SmartStart), and the Brown or BlueRev B
loop must be cut ( SmartStart).Rev A
b. Do connect the 2-pin harness (on SmartStart). Power and ground will be provided byNOT
the D2D connector.DBALL2
Connect SmartStart to using the D2D port.DBALL
SmartStart Installation
Connect 202 to using the D2D port.XL DBALL2
XL202 Installation
Refer to the Diagnostics section on page 2 for more information and for troubleshooting purposes.LED 1
&
Flashes
3
2X ENGINE
START
STOP
PUSH
Do NOT
press the
brake pedal
IMPORTANT: NOTDo press the brake pedal.
the Push-To-Start (PTS) button to turnPress twice
the ignition ON.
2
&
Off
Solid Green or
Orange x3 sec
The orange flashes then the green turns for 3 secondsLED LED ON
and shuts off.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the 202 or SmartStart module to 2, it is important to ensure that the proper feature andXL DBALL
function programming is selected using Xpress (version 4. or higher). Visit www.directechs.com to download the latestVIP 5
version of the application.
Warning! To take advantage of advanced features, you must use Xpress 4.5 (and higher) or the Directechs Mobile app.VIP
When the flashing operation is successful, you can proceed with the programming instructions below.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the button.Config for RSR
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your oader3.XKL
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select and follow the on screenFLASH YOUR MODULE
instructions.
Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.

Page 9
1If required for your installation, connect the 10-pin & 12-pin
harnesses to the module Press hold the rogramming. and p
button, then connect the 14-pin harness to the module.
10-pin
D2D
1st
12-pin
14-pin
2nd
4th
3rd
Warning gainst xecuting a Hard Reset!AE
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as and D2D options) may have to be reconfigured. See the section of this guide.RFTD Feature & Option List
2
Solid
&
Release
3Release the programming button. The turns solid red.LED ON
Module Reset
Hard Reset
2& &
1
Wait 3 seconds until the orange then release theLED turns solidON
p The turns solid red.rogramming button. LED ON
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module Press hold the rogramming. and p
button, then connect the 14-pin harness to the module.
10-pin
D2D
1st
12-pin
14-pin
2nd
4th
3rd
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web config tool will not be affected.
Solid Release Solid
Solid Flashes
&
Wait 3 seconds until the orange aitLED turns solid , and w 10 more secondsON
until the andLED starts to flash orange red.
Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.

Page 10
Feature & Option List
It is recommended to configure all features and options listed below thethe using configuration tool found on the module
flashing page on www.directechs.com. The web offers more options such as and ; however, manualEIPS RSR
configuration of the features is possible using the information on this page.
*DefaultOption
Feat. Operation Flashes/Options Description
1. Disabled* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
*Driver Priority Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
All Unlocks all doors on first press.
1. Disabled The OEM alarm will not be controlled by DBALL2 upon remote start. No disarm or arm command will be
executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
2. Safelock Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the
beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEMAlarm Control will synchronize with the OEMalarm so that it will disarm and rearm the vehicle in
the remote start sequence, onlywhen required. The reason for this is, factoryalarm control must often be done
by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to
honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to detect if the
disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm
will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory
alarm control is not done twice. Aremote starter, for which the Safelock feature is active, will work perfectly with
this option and will make it invisible to the user.
Smart OEM Alarm
Control
3
RFTD Output
Type
1
2Unlock Driver
Priority
Rev.: 20170814
Platform: DBALL2
Firmware: HYUNDAI4 (RSR)Remote Start Ready Installation
© 2017 Directed. All rights reserved.