Discount Car Stereo A2D-CDR30 Instruction Manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2D-CDR30
QUICK START BLUETOOTH MUSIC STREAMING INSTALLATION GUIDE FOR PORSCHE CDR30 & CDR31RADIOS
Created September 10, 2015
Revised November 3, 2021

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
Careless installation and operation can result in equipment damage.
Requirements:
cDr30 or CDR31 radio
Introduction
Porsche base radios (e.g., CDR30 and CDR31) may include optional 3.5mm AUX
jack and/or Bluetooth Hands-Free kit; which does not support music streaming
(A2DP). If looking to avoid wires dangling from the dash and support for more
attractive modern media formats, consider our A2D-CDR30 Bluetooth music
streaming add-on. This module supports any A2DP enabled Smartphone, Tablet,
Kindle etc. Once installed users pair device and wirelessly stream Apple music,
Pandora, turn by turn directions and more. The A2D-CDR30 replaces factory AUX
jack (if so equipped) and also works in vehicles with or without factory Hands-
Free.
FYI: Factory Hands-free option does not support streaming profile.
See Frequently Asked question at the end of this guide for more details.
Installation
Radio removal required to gain access to connectors. For radio removal
instructions click here for radio removal instructions.
1. If present, disconnect 12-pin GREEN plug from radio main Quadlock (See
Fig. 1) --- To disconnect, simply press release tab.
Fig. 1
Radio Quadlock
2. Connect adapter 12-pin BLACK plug to vacated slot from step 1 (See Fig. 2)
Fig. 2
Factory Green plug (if present) remains disconnected (See Fig. 2)
3. Secure ground wire to radio chassis as seen in Fig. 3
Use chassis screw to secure ground or connect to alternate ground source.

Fig. 3
Ground wire to radio chassis
4. Tap or connect Accessory RED wire to suitable 12V Accessory supply
source in vehicle (e.g., fuse box etc.) Find suggestions below.
Suggested 12V accessory supply options:
1. In 968: Left foot well Fuse box at Row C, Fuse 1 (7.5A/15A)
2. In 987: Kick Panel Fuse box at Row B, Fuse 9 (7.5A)
3. Alternate: Remove hand-brake cover, locate orange wire. (See Fig. 4)
To avoid battery drainage, ensure circuit to which you are connecting the
module 12V accessory wire is turning OFF with key prior to finalizing.
Voltmeter or test light recommended.
4. Tap WHITE wire (pin 12) on radio main Quadlock (See Fig. 5). This wire is
antenna/amp turn on which means it is controlled by radio ON/OFF button.
Fig. 4
below brake lever
Warning: Do not connect accessory wire to 12V battery (always on)
supply. Use voltmeter or test light to verify voltage and engine noise
prior to finalizing install. In case of engine noise, we recommend adding
a noise filter such as our NF3A
Secure module and proceed to pairing
Fig. 5
Radio main plug

Pairing
Pairing process varies among devices the but basic steps are the same. This
process is done upon initial install and will not have to be repeated.
1. Turn ignition and radio “ON”
LED inside module will blink (pairing mode)
2. On A2DP device: go to Settings, Wireless & Networks, Bluetooth
Settings
3. Select and enable Bluetooth
4. Select Bluetooth settings
5. Tap Scan for devices.
6. Wait for Bluetooth device name (See Fig. 6) to appear and select it.
LED will glow steady (paired)
Fig. 6
Note:
Pair multiple devices (10) but only one connection is supported.
Optional remote
Optional smart remote is not required for operation; however, instead juggling
Smartphone while driving (which is outright dangerous), simply install in a more
convenient place on dashboard or steering wheel to operate your smartphone:
(Controls do not apply to the CDR30/31 radio)
1. Track up/down
2. Activate Phone commands (Google play only)
3. Pause
4. Volume up/down
Pairing:

Operation:
Use wireless remote to perform the following functions on iOS7.0 and higher or
Android 4.4 and higher.
Package contents:
Operation
1. Turn radio “ON”
2. Press radio “CD/AUX” button repeatedly until “AUX MODE” is activated
or press “AUX” Soft key
3. Set radio volume to minimum setting
4. Launch Smartphone streaming application.
5. Set volume on audio device (smartphone etc.) to 75% or more
(important)
6. Carefully adjust radio volume in small steps until desired volume is
reached. If necessary, increase volume on audio device.
Warning: Playlist and Track selection *NOT* possible from radio. Use audio
device built-in controls or optional wireless remote to access and control
audio files.
Vehicles equipped with factory Hands-free option are required to pair two
separate devices. One for calls and another (SKY) for streaming.
7. If correct operation is confirmed, tuck away any extra wires and re-
install radio.

Frequent ask questions & troubleshooting
1. My Porsche has factory Hands-free, will the A2D-CDR30 interfere?
NO; The A2D-CDR30 adds Bluetooth music streaming features and does not
interfere with factory hands-free calls. When hands-free is in use, music
streaming will mute/pause.
2. My vehicle has an AUX jack. Will the A2D-CDR30 interfere with it?
YES; the A2D-CDR30 replaces factory AUX jack or iPod adapter.
3. How to remove CDR-30 and CDR-31 radios from the dash?
Click link below for help removing radio from dash.
https://www.youtube.com/watch?v=dlrPQftUvAs
4. I’m experiencing alternator whine. What can be done to fix this?
Engine noise is uncommon, however if you do experience engine noise, we
recommend locating an alternate ACC supply source or adding a noise filter
such as our NF3A
5. My module paired when first installed, but will not connect (pair)
when entering vehicle. What can be done to fix this?
It is possible module red wire is connected to a battery source (always on)
which explains why module paired initially but not thereafter. Please use
voltmeter or test light to ensure module is connected to 12V accessory
supply or one that does turn off/on with ignition or radio.
6. Will I be able to control Smartphone or Tablet from radio buttons?
NO; you must continue to use Smartphone or Tablet built-in controls
and display to operate device. Radio volume button is used to set
playback level. Optional smart remote is available to control audio device
7. Does this module work on Porsche PCM radios?
NO, this module works only on Porsche CDR30 and CDR31 radios.
8. Will I have to enable AUX on stereo at dealership?
In some vehicles, aux is already enabled; and those that are not will require
dealer activation. For verification: Press “CD” button repeatedly to cycle
between CD and AUX, if only CD appears, yours will require dealer
activation.
Disclaimer
• This product has no affiliation with Porsche
• We’re not liable for misuse of this product.
•Aux mode must be enabled otherwise visit nearest Porsche dealer
• We recommend professional installation.
For additional help email [e-mail]

© 1995-3-Nov-21 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.