Dish Network 622 guide Manual

622
SETUP
INSTRUCTIONS

• If you are not seeing the screens listed in this guide, try changing your TV’s
input by pressing the “Source/Input” button on your TV.
• In step 7, your replacement receiver will test your Internet and phone
connection. If the results display as “not available,” ensure the cords are
connected to the appropriate ports on the back of your receiver and to your
phone/modem.
• To find your closest UPS dropo location or to schedule a pickup at your cost,
call 1-800-742-5877 or visit ups.com/dropo.
Do you have questions?
Take a look at the back cover of this guide for this contact information!
2

Disconnect Your Cables and Remote
Antenna
Locate the power cable for the
receiver that you are replacing,
and unplug it from the wall.
Locate the antenna connected
to the “Remote Antenna” port.
Then unscrew the antenna
from the receiver.
Locate the cable(s) connected
to the “Satellite In” ports, and
then unscrew the cable(s) from
the receiver. Do not unscrew the
cable(s) from the wall.
3

Ethernet
Ethernet
Locate the cable connected to the “Ethernet” port. Then,
unplug the cable from the receiver. Do not unplug it from
the wall. (You may not have this cable.)
PHONE
Locate the cable connected to
the “Phone” port. Then unplug the
cable from the receiver. Do not
unplug it from the wall. (You may
not have this cable.)
Disconnect Your Cables and Remote
Antenna
HDMI 1
Determine the cable you are
using to receive audio/visual
signal. Then unplug it from the
receiver, but not from your TV.
L
R
AUDIO
VIDEO
OR
HDMI CABLE RCA CABLES
4

Connect the Satellite In cable(s)
to the “Satellite In” port(s) on
your replacement receiver.
Connect the remote antenna to
the “Remote Antenna” port on
your replacement receiver.
Connect Your Cables and Remote
Antenna
5

Ethernet
Ethernet
Connect the Ethernet cable to the “Ethernet” port
on your replacement receiver. (You may not have
this cable.)
PHONE
Connect the Phone cable
to the “Phone” port on your
replacement receiver. (You may
not have this cable.)
Connect either the RCA cables
or the HDMI cable to the
corresponding port(s) on your
replacement receiver.
Connect Your Cables and Remote
Antenna
HDMI 1
L
R
AUDIO
VIDEO
OR
HDMI CABLE RCA CABLES
6

03
Power Your Equipment
Plug the power cord from your
receiver into a power outlet,
and ensure that your TV is still
plugged in. Turn on your TV. It
could take up to 30 seconds for
you to see any images.
Make sure that the SmartCard is
secured firmly in the slot on the
front of your receiver.
7

Program Your Remote
If you are using a second TV with this
receiver, repeat to program the remote
that has the blue number 2 identifier
at the bottom. Once complete, use the
arrow buttons on your remote to highlight
“Continue,” and then press Select.
Your screen should now display the Program
TV1 Remote to Receiver screen. Follow the
onscreen instructions to program your remote
that has a green number 1 identifier at the
bottom to the replacement receiver. Once your
remote is programmed, use the arrow buttons
on your remote to highlight “Continue,” and then
press Select.
8

Download Receiver Software
Your receiver will start downloading
software automatically.
Once the software download is
complete, your receiver will update
automatically.
9

Set Your TV Configuration
If you have a second TV, see what channel it
is currently tuned to by using the TV’s remote
or the buttons on the TV itself to channel
up and then channel back down. Select the
appropriate channel onscreen according to
what channel your TV is tuned to, and then
select “Continue.”
Follow the onscreen instructions to
set your TV’s video resolution so
the picture will display properly.
Once your TV resolution is set, use
the arrow buttons on your remote
to select “Save,” and then press
Select.
10