DITEC ENTREMATIC AS45 User manual

Installation manual for
panic devices.
(Original instructions)
AS45
IP2042EN - rev. 2012-07-24
DITEC S.p.A.
9ia 0ons. %an¿ - 21042 Caronno Pertusella (9A) - ITA/<
Tel.  02 11 - )a[ 02 014
www.ditec.it - [email protected]
EN

2
IP2042EN 2012-07-24
INDEX
LIST OF UTENSILS
LIST OF PROFILES AND SEALS
Tape measure
Pencil
Phillips screwdriver
)lathead screwdriver
Scissors
mm Allen Ne\
4 mm Allen Ne\
mm Allen Ne\
mm Allen Ne\
.CP)
mm Allen Ne\for tightening the e[-
panders [18] with special bit
10 mm socNet wrench
Drill
Pliers
Nippers
Saw
/evel
TOPIC PAGE
/ist of pro¿les and seals 2
/ist of utensils 2
AST PANIC SYSTEM 
1. AST mobile wing installation 4
2. AST ¿[ed wing installation 10
. AST electrical connections 1
ASME PANIC SYSTEM 17
4. ASME mobile wing installation 18
. ASME electrical connections 24
ASMI PANIC SYSTEM 2
. ASMI mobile wing installation 2
7. ASMI electrical connections 2
100 80 8187
 8124 88
800 820 2 8
80 821 0SPAZ14
808 822 417SPAZ4811
All right reserved
All data and speci¿cations have been drawn up and checNed with the greatest care. The manufacturer cannot however taNe an\
responsibilit\for eventual errorsommisions or incomplete data due to technical or illustrative purposes.

3IP2042EN 2012-07-24
AST panic devices are TÜV approved for use with DITEC TEN
and VA/O5model automations.
Each carriage installed must be connected to the mobile panic
wing b\at least two fastening points.
The wings to be used are intended as having been built with
DITEC PAM4/ and PAM4M series pro¿les.
The ma[imum height of the mobile panic wing (+M) must not
e[ceed 2400 mm.
The dimensions (/M) and the ma[imum weight of the door that
can be NnocNed out must compl\with the following graphs for
one and two mobile door automations.
Note: For dimensions and/or weights which are not accounted
Ior in the diagramcon¿rm the IeasiEiOit\oIthe SroMect with our
technicaOcommerciaOoI¿ces
600 8000
0
80
20
40
60
100
120
1000 1200
mm
1400 max
kg 1 wing automation
VALOR L - VALOR P - REX - TEN
VALOR B - VALOR N
MAX
MAX 100
120
AST
600 8000
0
80+80
20+20
40+40
60+60
100+100
120+120
1000 1200
mm
1400 max
kg
TEN
VALOR B - VALOR N
MAX
MAX
MAX
MAX REX
VALOR L - VALOR P
2 wings automation
90+90
70+70
70+70
90+90
100+100
120+120
If the width of the mobile panic wing (/M) is greater than 1000
mmadd reinforcement 417(see ¿g. 1)
If the width of the mobile panic wing (/M) is greater than 1200
mmadd reinforcement the third carriage.
If the weight of the mobile panic wing is greater than 0 Ngadd
Nit .AS4to the lower portion (see ref. 1 ¿g. 2).
Note: 2nO\ Ior 3$0/ ,I the weight oIthe door does not e[ceed
 Nguse the .,F Nit in the Oower Sart see reI  ¿g 
The ma[imum height of the ¿[ed panic wing (+)) must not
e[ceed 2400 mm.
The width of the ¿[ed panic wing (/)) must not e[ceed 100
mm and the weight must not e[ceed 100 Ng.
REF. KIT Q.T.
AST1 Q.T. AST2 SERIE
10KIT AST1 Q.T. PAM4/
1 KAS4AST2 SE5I-
ES
PAM4/
PAM4M
2--4---
7-2
KASM141 PAM4/
PAM4M
KASM24-1
10 KI)41 2 PAM4/
820
24
100
417
SPAZ4811
KASMG14
KASMN14 12
PAM4/
PAM4M
1-11-12-1-
14-1-1-
17-18-1-
20-21-22-
2-24-2
KAST1A4) 12
PAM4/
PAM4M
27 1CE/P522
PAM4/
PAM4M
Note: 8se .it &(/35 iI\ou wish to instaOO the ShotoceOOs that
detect the Sresence oISeoSOe and oEMects in the Sassage cham
Eer see reI  Sag
$ttention: 8se the 3$0/ $67 or 3$00 $67 manuaOs
to determine the cut measurements, the kits required and
the required Sro¿Oe SreSarations
$ttention:
8
se the 3$0

/$
6
7or 3$0

0$
6
7manuaO
s
t
o determine the cut measurements, the kits required an
d
t
he required Sro
¿
Oe SreSarations
i

4
IP2042EN 2012-07-24
1600230x30
3924
HM
717 56
45
4
SPAZ4811
3820
*4173
SPAZ4811
6
3
57
1930330303040
4xØ6,54xØ6,52xØ6,5
150
340
35 33
98
16
24
4xØ4,2
24
35 33
600< LM < 1400
3
1. AST MOBILE WING INSTALLATION
() Onl\with /M !1000
)ig. 1

5IP2042EN 2012-07-24
63820+SPAZ4811
1 8
8
9
8
8
4 1
3 7
1
5
3808 (*3821)[phone] (*3821)+3839
3805+SPAZ14
3831+3838 3837
1600 1
*10
23800 (*3599)+3839
3813 (*3822)+3839
** **
*10
26
3924+SPAZ4811
6
6
4
160
() PAM4/
() Onl\with mobile wing !0 Ng
Adjustments to be performed during installation
)ig. 2

6
IP2042EN 2012-07-24
1.1 Insert the seal 8 into the PAM4M pro¿les 800808
and 81or else the PAM4/ pro¿les  821 and 822as
shown in the diagram.
1.2 Shorten the seal to the si]e of the pro¿le.
1.Insert detail [1] into the PAM4M pro¿les 800 and 81
or else the PAM4/ pro¿les  and 822and fasten it as
shown in the diagram.
1.4 -oin the vertical pro¿les with the hori]ontal pro¿les and fa-
sten them as shown in the diagram.
Note: :ith 3$0/ Sro¿Oes, the gOass >@ must Ee inserted
when Moining the YerticaOand hori]ontaOSro¿Oes
7he gOass suSSort sSacers must Ee SroSerO\ aSSOied to the Iour
sides  and must Ee adMusted as shown in SaragraSh 
1.)asten pro¿le 80to the lower portion of the wingas
shown in the diagram.
1.Insert the brushes SPAZ14 as shown in the diagramand
blocNthem to prevent them from sliding.

7IP2042EN 2012-07-24
1.7 Insert detail [2] into the lower portion of the wing and fasten
it as shown in the diagram.
1.8 Insert detail [] into the upper portion of the wingas shown
in the diagram.
1.)asten detail [] b\tightening the eight fastening screws
as shown in the diagram.
1.10 Insert the brush SPAZ4811 into pro¿les 24 and 820as
shown in the diagram.
1.11 )asten pro¿le 24 to the upper portion of the wingas
shown in the diagram.
1.12 )asten detail [4] to pro¿le 24as shown in the diagram.
Note: %e sure to take note oIthe wing¶s oSening direction
1.1Trim the brush SPAZ4811 where it connects with detail
[]as shown in the diagram. Note: Be sure to take note of the
wing¶s oSening direction
1.14 Insert pro¿le 820 into detail []as shown in the dia-
gram.

8
IP2042EN 2012-07-24
1.1)asten detail [] to pro¿le 820as shown in the dia-
gram.
Note: during the instaOOation of the ¿[ture, in order to oEtain the
SroSer hori]ontaOSosition of the moEiOe Sanic wing, Ooosen the
fastening screws and adMust the screw shown in detaiO>@, as
shown in the diagram
1.1If the width of the mobile wing is greater than 1000 mm
insert reinforcement 417into pro¿le 820as shown in the
diagram.
1.17 Insert detail [] into pro¿le 820as shown in the diagram.
Note: Be sure to take note of the wing¶s oSening direction
1.18 Position detail [] in correspondence to detail [4] and fa-
sten it as shown in the diagram.a.
Note: during the instaOOation of the ¿[ture, in order to oEtain the
SroSer Ereakawa\strength for the moEiOe wing, use the OateraO
screws to adMust detaiO>@, as shown in the diagram 
1.1Insert detail [] into pro¿le 820 near detail []as shown
in the diagram.
1.1 Insert the seal 87 onto the PAM4M pro¿le 808or else
the PAM4/ pro¿le 821as shown in the diagram.
$ttention: 2rient seaO as indicated in the ¿[tures manuaO
0ake a hoOe in the seaOthat corresSonds with the thickness
adMustment of the Sush gOass >@ as shown in the Sicture
1.21 Insert detail [7] into pro¿le 820as shown in the dia-
gram.
$ttention: 2rient detaiO>@ in the same manner as seaO

9IP2042EN 2012-07-24
1.22 Attach the supplied hooNto the lower part of the wing
as shown in the diagramin order to prevent seal 87 from
sliding.
1.2Attach pro¿le 81 to the PAM4M pro¿le 808or else to
the PAM4/ pro¿le 821as shown in the diagram.
1.24 Insert seal 88 into pro¿le 81as shown in the dia-
gramand blocNit to prevent it from sliding.
1.2Close the visible holes with the supplied capsas shown
in the diagram.
1.2:ith PAM4M pro¿lesinsert the glass [] into the mobile
wingas shown in the diagram.
A
A
1.27 Set the glass spacers [A]shown in the diagramso that
the\provide proper support.
NB: when instaOOing the ¿tting, adMust the Sush gOass sSacers
>@ as shown in the Sicture , for the moEiOe door wing to reach
the hori]ontaOSosition.
1.28 :ith PAM4M pro¿lesinsert the seals into the glass-blo-
cNing pro¿les [8]as shown in the diagram.
1.2:ith PAM4M pro¿lesinsert the glass-blocNing pro¿les
[8] onto the mobile wing until the\clicN as shown in the dia-
gram.

10
IP2042EN 2012-07-24
2. AST FIXED WING INSTALLATION
3809 + SPAZ4811 3924 + SPAZ4811
12
11
24
13
20
HM
LM
3924+SPAZ4811
3809+SPAZ4811
14 16
22
23
15 13
1719
21
)ig. 

11 IP2042EN 2012-07-24
21
3809+SPAZ4811
10 8
8
19
13
9
8
8
16
1818 23 1522
3924+SPAZ4811
3813+(*3822)+3839
3800 (*3599)[phone] + SPAZ14
3808 (*3821)+3839
3808 (*3821)+3839
3809 + SPAZ4811
3924+ SPAZ4811 3831
20
14
17
18
18
18
12
25
13
24
11
10
10 10
27
27
6
6
6
6
46
() PAM4/
Adjustments to be performed during installation
------- Photocell and magnetic micro-switch cable route
)ig. 4

12
IP2042EN 2012-07-24
2.1 Insert the seal 8 into the PAM4M pro¿les 800808
and 81or else the PAM4/ pro¿les  821 and 822as
shown in the diagram.
2.2 Shorten the seal to the si]e of the pro¿le.
2.-oin the vertical pro¿les with the hori]ontal pro¿les and fa-
sten them as shown in the diagram.
Note: :ith 3$0/ Sro¿Oes, ,nsert detaiO>@ into Sro¿Oes 
and , as shown in the diagram
Note: :ith 3$0/ Sro¿Oes, the gOass >@ must Ee inserted
when Moining the YerticaOand hori]ontaOSro¿Oes
7he gOass suSSort sSacers must Ee SroSerO\ aSSOied to the four
sides  and must Ee adMusted as shown in SaragraSh 
2.4 Insert detail [11] into the lower portion of the wing and fa-
sten it as shown in the diagram.
2.Insert the brushes SPAZ14 upon pro¿le 80and blocN
them to prevent them from sliding. )asten pro¿le 80to the
lower portion of the wingas shown in the diagram.
2.Insert detail [12] into the lower portion of the wing and fa-
sten it as shown in the diagram.
2.7 Insert the photocell [2]which detects the opening of the
mobile winginto pro¿le 81as shown in the diagram.
NB: the ShotoceOOs >@ that detect the Sresence of SeoSOe and
oEMects in the Sassage chamEer can Ee inserted as shown in
Sicture 

13 IP2042EN 2012-07-24
2.8 )eed the cable through the upper portion of the wing and
maNe it to come out in order to allow for the connection of the
magnetic limit switchas shown in the diagram.
2.MaNe the limit switch and photocells cables come out of the
hinge side vertical uprightas shown in the diagram.
2.10 Attach pro¿le 81 and insert detail [1]as shown in the
diagram.
2.11 Insert and fasten detail [14]as shown in the diagram.
Note: 'uring the instaOOation of the ¿[ture, adMust detaiO>@ so
that detaiO>@ is SroSerO\ connected Eetween the ¿[ed wing ad
the Serimeter Sro¿Oe
2.12 Attach the magnetic limit switch [1] to its relative bracNet
as shown in the diagram.
2.1Insert the brush SPAZ4811 into pro¿les 24 and 80 as
shown in the diagramand blocNit to prevent it from sliding.
2.14 )asten detail [1] to pro¿le 24as shown in the dia-
gram.
2.1)eed the cable through the upper portion of the wing and
maNe it to come out in correspondence to the photocell cable
as shown in the diagram.

14
IP2042EN 2012-07-24
2.1)asten pro¿le 24 to the upper portion of the wingand
perform the proper connectionsas shown in the diagramma-
Ning reference to page 1.
2.17 )asten detail [1] to pro¿le 24as shown in the diagram.
Note: Be sure to take note of the wing¶s oSening direction
2.18 )asten pro¿le 24 to the hinge side vertical uprightas
shown in the diagram.
2.1)asten detail [17]as shown in the diagram.
2.20 )asten the e[panders [18] to the perimeter pro¿les 80
as shown in the diagramusing the appropriate mm Allen
Ne\.
Note: 'uring the instaOOation of the ¿[ture, the Serimeter Sro
¿Oes  must Ee attached to the waOO and OeYeOed with the
e[Sanders
2.21 )asten detail [1] to pro¿le 80 as shown in the dia-
gram.
Note: 'uring the instaOOation of the ¿[ture, the caEOes coming
out of the ¿[ed wing must Ee fed through detaiO>@
2.22 )asten detail [20] to the lower portion of pro¿le 80 as
shown in the diagram.
2.2)asten detail [21] to the upper portion of pro¿le 80 as
shown in the diagram.

15 IP2042EN 2012-07-24
2.24 )asten detail [22] to pro¿le 80 situated above the wing
as shown in the diagram.
Note: 'uring the instaOOation of the ¿[ture, detaiO>@ must Ee
Sositioned in corresSondence to its internaOconnection with de
taiO>@ and the Erush 63$= must Ee trimmed
,n addition, in order to oEtain the SroSer Ereakawa\strength for
the ¿[ed wing, use the OateraOscrews to adMust detaiO>@
2.2During the installation of the ¿[turedetail [2] must be
positioned in correspondence to the magnetic limit switch [1].
Drill the appropriate holes in order to fasten detail [2] to pro¿le
80 situated above the wingas shown in the diagram.
2.2:ith PAM4M pro¿lesinsert the glass [] into the ¿[ed
wingas shown in the diagram.
A
A
2.27 Set the glass spacers [A]shown in the diagramso that
the\provide proper support.
2.28 :ith PAM4M pro¿lesinsert the seals into the glass-blo-
cNing pro¿les [8]as shown in the diagram.
2.2:ith PAM4M pro¿lesinsert the glass-blocNing pro¿les
[8] onto the mobile wing until the\clicN as shown in the dia-
gram.
2.0 During the installation of the ¿[tureposition detail [24] in
correspondence to detail [11] on the ¿[ed wing and fasten it to
the Àoor so that it is aligned with the ¿[tureas shown in the
diagram.
2.1 During the installation of the ¿[turefasten pro¿le 100
to the Àooras shown in the PAM4/ AST or PAM4M AST
manual.
Note: 'o not Saint Sro¿Oe  after it has Eeen fastened to
the Àoor

16
IP2042EN 2012-07-24
RXTX
OPENOPEN
CONTROL PANEL
COMH-K
Magnetic switch Magnetic switch
Brown
Blue
Brown
Blue
Black
Blue
Black
Brown
DO NOT
CONNECT
Blue
Black
Brown
0
1
9
STOP
9
TX
Grey Black
LED
RX
25
15
23 23
15
25
13
103
25
- Perform the electrical connections as shown in the diagram.
$ttention: ,f the &20+. function seOector is used, connect
the receiYer¶s Erown caEOe to terminaOon the seOector
- An\other arrest devices must be connected in series to
terminal (STOP).
- :hen the receiver (5;) and the transmitter (T;) of the
photocell SIC852 are powered and correctl\alignedthe
green /ED on the transmitter T;and the \ellow /ED on the
receiver 5; will light up. The \ellow /ED on the receiver will
go out when the\are no longer correctl\aligned.
- Once installation has been completedchecNto maNe sure
that the force required to open each single wing does not
e[ceed 220 N.
This reading must be taNen at 1 m from Àoor level in corre-
spondence to the closure side of the wing (opposite to the
hinges). The breaNawa\force can be adjusted as indicated
in paragraph 1.18 and 2.24.
- ChecNthat the door¶s automatic movement stops when the
wings (mobile and ¿[ed) are released. The SIC852 pho-
tocell serves the purpose of detecting the release of the
mobile wings while the magnetic micro-switch serves the
purpose of detecting the release of the ¿[ed wings.
- If installedthe photocells CE/P5[27] that detect the pre-
sence of people and objects in the passage chamber must
be connected as shown in the manual of the electronic con-
trol panel of the automation s\stem.
3 AST ELECTRICAL CONNECTIONS

17 IP2042EN 2012-07-24
ASME panic devices are TÜV approved for use with DITEC TEN
and VA/O5model automations.
Each carriage installed must be connected to the mobile panic
wing b\at least two fastening points.
The wings to be used are intended as having been built with
DITEC PAM4/ and PAM4M series pro¿les.
Note: 7he $60( Sanic s\stem can aOso Ee aSSOied to wings
which haYe Eeen EuiOt with non'itec Sro¿Oes
7he kits .$60, .$60 and .$60*/.$60N must
Ee used, as indicated in the taEOe
7he si]e and weight Oimits indicated EeOow must Ee resSected
when assemEOing the wings
7he aOuminum Sro¿Oes used to construct the Sanic wings must
Ee comSatiEOe with the $60( Sanic s\stem
3erform an\work required in order to adaSt the kits, making
reference to the measurements indicated in the 3$0 $60(
manuaOs
7h9 aSSroYaOwiOO Ee Yoid in the case that non'itec Sro¿Oes
are emSOo\ed
The ma[imum height of the mobile panic wing (+M) must not
e[ceed 2400 mm.
The dimensions (/M) and the ma[imum weight of the door that
can be NnocNed out must compl\with the following graphs for
one and two mobile door automations.
Note: For dimensions and/or weights which are not accounted
for in the diagram, con¿rm the feasiEiOit\of the SroMect with our
technicaOcommerciaOof¿ces
ASME
600 8000
0
80
20
40
60
100
120
1000 1200
mm
1400 max
kg 1 wing automation
VALOR L - VALOR P - REX - TEN
VALOR B - VALOR N
MAX
MAX 100
120
600 8000
0
80+80
20+20
40+40
60+60
100+100
120+120
1000 1200
mm
1400 max
kg
TEN
VALOR B - VALOR N
MAX
MAX
MAX
MAX REX
VALOR L - VALOR P
2 wings automation
90+90
70+70
70+70
90+90
100+100
120+120
If the width of the mobile panic wing (/M) is greater than 1000
mmadd reinforcement 417(see ¿g. )
If the width of the mobile panic wing (/M) is greater than 1200
mmadd reinforcement the third carriage.
If the weight of the mobile panic wing is greater than 0 Ngadd
Nit KAS4to the lower portion (see ref. 1 ¿g. ).
Note: onO\ for 3$0/ ,f the weight of the wing is not greater than
 kg, use kit .,F to the Oower Sortion see ref ¿g
The following table lists the contents of the Nits.
REF. KIT Q.T.
ASME1 Q.T. ASME2 SERIES
10KIT 1 1 PAM4/
1 KAS412 PAM4/
PAM4M
1-2KASM1A4) 12
PAM4/
PAM4M
2--4---
7-2
KASM141 1 PAM4/
PAM4M
KASM24-1
2KASME411
PAM4/
PAM4M
820
24
100
417
SPAZ4811
KASMG14
KASMN14 12
PAM4/
PAM4M
$ttention: 8se the 3$0/ $60( or 3$00 $60(
manuaOs to determine the cut measurements, the kits
required and the required Sro¿Oe SreSarations
$ttention:
8
se the 3$0

/$
6
0( or 3$0

0$
6
0(
m
anuaOs to determine the cut measurements
,
the kit
s
r
equired and the required Sro
¿
Oe SreSarations
i

18
IP2042EN 2012-07-24
1600230x30
3924
HM
717 56
45
4
SPAZ4811
3820
*4173
SPAZ4811
6
3
57
1930330303040
4xØ6,54xØ6,52xØ6,5
150
340
35 33
98
16
24
4xØ4,2
24
35 33
600< LM < 1400
3
4. ASME MOBILE WING INSTALLATION
() Onl\with /M !1000
)ig. 

19 IP2042EN 2012-07-24
63820+SPAZ4811
1 8
8
9
8
8
4 1
3 7
1
5
3808 (*3821)[phone] (*3821)+3839
3805+SPAZ14
3925 3837
1600 1
*10
23800 (*3599)+3839
3813 (*3822)+3839
** **
*10
26
3924+SPAZ4811
6
6
4
160
() PAM4/
() Onl\with mobile wing !0 Ng
Adjustments to be performed during installation
)ig. 

20
IP2042EN 2012-07-24
4.1 Insert the seal 8 into the PAM4M pro¿les 800808
and 81or else the PAM4/ pro¿les  821 and 822as
shown in the diagram.
4.2 Shorten the seal to the si]e of the pro¿le.
4.Insert detail [1] into the PAM4M pro¿les 800 and 81
or else the PAM4/ pro¿les  and 822and fasten it as
shown in the diagram.
4.4 -oin the vertical pro¿les with the hori]ontal pro¿les and fa-
sten them as shown in the diagram.
Note: :ith 3$0/ Sro¿Oes, the gOass >@ must Ee inserted
when Moining the YerticaOand hori]ontaOSro¿Oes
7he gOass suSSort sSacers must Ee SroSerO\ aSSOied to the four
sides  and must Ee adMusted as shown in SaragraSh 
4.)asten pro¿le 80to the lower portion of the wingas
shown in the diagram.
4.Insert the brushes SPAZ14 as shown in the diagramand
blocNthem to prevent them from sliding.