Dive Rite BC1080Q User manual

Packaging contains:
1) 6-ft of 2-inch Harness webbing,
with stainless-steel grommet
2) 2 tubular sleeves (4" each)
3) 2 tubular sleeves (5" each)
4) 1 Right waist-strap assembly
(3.5-ft 2-inch webbing with one
D-ring)
5) 1 Left waist-strap assembly
(3.5-ft 2-inch webbing with
one
D-ring and quick-release
buckle)
6) 5 Stainless steel belt-Slides
7) 2 Stainless steel D-rings
8) 1 Stainless steel bent D-ring
9) 1 Stainless steel waist strap
release belt buckle
10) Left and right chest strap
Assembly
Deluxe Quick Release Harness
Item # BC1080Q
This harness utilizes nylon webbing for
strength and comfort. It also features
tubular webbing sleeves
to minimize wear wherever the
harness would normally be in
contact with a metal backplate.
The Dive Rite Deluxe Harness fits on
all Dive Rite back-plates.
Great for technical diving
with a backplate.
Swivel points on the shoulder-straps and
a chest strap ensure
a comfortable fit.
The quick-release buckle allows for
easy don/doff of the harness.
** Crotch Strap not included **
www.DiveRite.com
BC1080Q Deluxe Quick Release Harness_Oct 30, 2012

D
Threading Deluxe Harness with Quick-Release
RIGHT EFT
A
BACK
Shoulder Strap Routing
STEP
7
B
FRONT
C
Waist Strap
Routing
STEP
6
Minor
Adjustment
Major
Adjustment
1) Begin by threading 2 tubular sleeves onto the 6-foot
piece of harness webbing. These will end up where the
harness goes through the upper harness strap slots, as
shown in figure A.
2) Thread the 6-foot webbing piece through the upper
shoulder strap slots, as shown in Figure A, positioning the
webbing so the grommet is over the upper tank bolt-
hole.
3) Thread the remaining 2 tubular sleeves onto the 3-foot
sections of the webbing, with them ending up where the
two sections go through the waist slots, as shown in figure
C.
4) Using the right waist strap assembly (without the
quick-release buckle), weave the tail end through the two
left (looking at the front of the back plate) waist slots -
starting from the front, then through the inner slot, and
back out through the outer slot again.
5) Repeat step 4 with the left waist-strap assembly (with
the quick-release buckle).
6) Using Figure B, install one 2" belt slide and one 2" D-ring
on each tail of waist straps.
7) Using Figure B, install one 2-inch belt slide on each
shoulder strap.
8) Install one 2" belt slide with one 2" bent "D"-ring on
right shoulder strap.
9) Weave the tail of the right shoulder-strap through the
D- ring located on the waist-strap as shown. Then weave
the webbing back through both 2" belt slides.
10) Weave the tail of the left shoulder-strap through the
slot in the quick-release buckle on the left waist-strap.
Then weave the webbing back through the 2” “belt-slide.
11) Using the right chest-strap assembly (with buckle), loop
the webbing through right-side pivot D-ring and weave back
through the plastic belt slide.
12) Using the left chest-strap assembly, loop webbing
through the left-side pivot D-ring and pull tail through ring.
13) Weave tail of left chest-strap assembly through the
slots in the quick-release buckle of the right-side chest-
strap assembly.
14) Install the crotch strap components, as shown in Fig.
"D".
15) Install the waist-strap release buckle on the same side
of the waist-strap as the crotch-strap loop is installed.