Dive Rite Hurricane User manual

1
Copyright 2009 Lamartek Inc. D/B/A Dive Rite
Dive Rite Hurricane Regulator
Service Manual
All manuals and user guides at all-guides.com

2
•This manual is only to be used as a guide for a trained/ certified
Dive Rite Regulator technician.
•Possession of this guide does not qualify any individual in the service of
Dive Rite Breathing Systems.
•Only qualified Dive Rite Dealers can Service Dive Rite Products.
•Improper servicing can lead to serious injury or death.
Warning
All manuals and user guides at all-guides.com

3
Table of contents
• Pages 4-17 Disassembling the Second stage
• Pages 18-29 Assembling the Second Stage
• Pages 33-46 Disassembling the First Stage
• Pages 48- 57 Assembling the First Stage
All manuals and user guides at all-guides.com

4
Note the location of plugs and
hoses.
Remove all low pressure hoses.
Remove high pressure hoses and
remaining port plugs.
All manuals and user guides at all-guides.com

5
1) Remove the LP hose using
17 mm and 14 mm wrenches
2) Remove the mouthpiece
All manuals and user guides at all-guides.com

6
3) Remove the locking ring, Washer, Cover and Diaphragm
All manuals and user guides at all-guides.com

7
4) Using a 17mm wrench loosen the
Locking Nut
5) Remove the Locking Nut, Spacing
Collar and “O” ring
All manuals and user guides at all-guides.com

8
6) Remove the entire Lever arm/
Poppet assembly by first pressing
the lever arm down and pushing
the assembly out through the
Adjustment side.
All manuals and user guides at all-guides.com

9
Take note of the opening on the assembly in relation to the lever arm
All manuals and user guides at all-guides.com

10
8) Remove the end cap from the adjustment knob with a small screwdriver
9) Using a Phillips head screwdriver remove the locking screw
All manuals and user guides at all-guides.com

11
10) Using a 16 mm and 17mm
set of wrenches loosen the Adjustment
Housing.
11) Remove the Deflector
All manuals and user guides at all-guides.com

12
12) Remove the balance chamber
Adjuster using 7mm socket or nut
driver
Note: it is not necessary to use the
Ratchet
Balance chamber
All manuals and user guides at all-guides.com

13
13) Remove the “O” ring from
The deflector
14) Remove the “O” rings from the
Adjustment housing
All manuals and user guides at all-guides.com

14
15) Remove the Poppet
Assembly, Spring and
Balance chamber
16) Remove the lever arm
All manuals and user guides at all-guides.com

15
17) Insert a 5mmm wrench and
Unscrew the valve seat inside the
Poppet chamber
18) After loosening the valve seat
It will be necessary to push the seat
Out with the tip of a pencil
All manuals and user guides at all-guides.com

16
19) Remove “O” ring
20)Remove Exhaust Tee
By gently pulling
21) Inspect Exhaust valve
All manuals and user guides at all-guides.com

17
Warning!!! Only original Dive Rite parts are to be used
All parts that are removed from the
serviced regulator and replaced by those
in the parts kits are to be returned to Dive
Rite.
Remaining parts should be cleaned in a
solution compatible with Nitrox use.
All points of lubrication should use a
Nitrox compatible lubricant.
This completes disassembly of the hurricane second stage
All manuals and user guides at all-guides.com

18
Assembling the Dive Rite Hurricane Second Stage
1) Begin by installing exhaust valve
All manuals and user guides at all-guides.com

19
2) Install the exhaust tee, insuring that
The tee edge is under the rim
Rim
Properly installed
All manuals and user guides at all-guides.com

20
3) Install lever arm take note of the orientation to the opening
on the tube
All manuals and user guides at all-guides.com