dji Alladin Spotlight User manual

ALADDIN SPOTLIGHT
The user manual
V1.1 20190328

Precautions Before Use
⚫Do not look directly at the spotlights and laser pointer.
⚫Do not block the cooling air inlet and vent;
⚫Do not interfere with the stability of the beacon.
⚫Do not touch the lamp holder body at work with bare hands.
⚫Please do your best to avoid using the equipment continuously for a long time in
extreme environment to extend the service life of the equipment;
⚫Such as hanging in gimble M210 / M210RTK, please put this product on first gimbal
port，average camera on second gimbal port;
⚫Please read the notes carefully;
Product Overview
Introduction
ALADDIN is a uav searchlight designed based on DJI PAYLOAD SDK. It integrates a triaxial
stabilized cradle head and a laser pointer, which can be directly mounted to the cradle
head interface. It supports the DJI industry uav dual cradle head linkage, and can provide
multi-angle illumination and laser indication for the target object.Can be widely used in
fire, military police and emergency rescue departments and other night lighting and
instructions;
Part Name
1 Skyport
2 Motor
3 Heat Dissipation
4 Laser Designator
5 Spotlight
6 Fan
1
2
5
4
3
6

The Installation
Installation preparation
1. Support model: M200 series; M200 V2 series;
2. Please upgrade the aircraft equipment to the latest firmware;
3. Please ensure the normal state of the aircraft before use;
Installation
4. Remove protective cover;Put the horizontal roller and pitching axis of the cloud lamp
in the correct direction, as shown in figure;
5. Align the white point of the cradle head interface with the red point of the aircraft
interface, and then embed the cradle head;
6. Rotate the interface of the cradle head camera to the locking position and align the
red dots to fix the cradle head;
Control Operation
Remote Control Operation
Dial the wheel around
Left wheel control pitch right wheel control translation
Shortcut keys
⚫One-click back to center (professional version remote control should be set by
yourself)
⚫More shortcuts open with the DJI Pilot update

DJI PILOT Control
Connect to DJI Pilot APP
1. Open the aircraft and remote control, ground mobile equipment;
2. When the connection is successful, DJI PILOT displays the "ALADDIN Spotlight" load
name.
The Function Menu

Load setting page:
⚫Laser indicator switch (Laser control)
⚫Laser indicator mode
⚫Searchlight switch :(Led control)
⚫Searchlight mode :(Led mode)
⚫Gimbal return head
⚫Gimbal speed
⚫Gimbal set offset
⚫Panel information display
⚫Temp protect
Functional Specifications
Gimbal
One key back to the cradle head: the cradle head rotates to the forward position
relative to the aircraft;
Follow mode: the cradle head follows the course of the aircraft;
Offset calibration: calibrate the initial middle position of the cradle head;
Speed adjustment: adjust the rotation speed of the dial wheel or the cradle head on
the touch screen;
Light Control
Laser indicator mode: select indicator laser flicker mode, which are long light and flicker
respectively;
Searchlight mode: select the flashing mode of the searchlight, which are long light,
explosion flash and SOS.
Panel information display: searchlight information panel switch;
Temperature protection switch: when the temperature is more than 80 degrees, high
temperature protection, and turn off the searchlight, but retain the laser pointer;
Double Head Linkage
Synchronizing the control attitude of two cradle head;Support X4S, X5S, Z30 X7;
The cloud desk lamp must be mounted in position 2 when linkage, namely the left
side of the official head; 1 position mounted main head camera;
It is absolutely forbidden to mount two cloud lamps and light them at the same time,
which will lead to power overload of the uav. Currently, dual light mounting function
is not supported for the model.

Notes:
⚫The cradle head supports the two modes of hanging down and hanging up. During
installation, the cradle head needs to be placed in the right direction for
connection, otherwise the cradle head will be blocked or work abnormally.
⚫It is normal that the cradle head will have a slight swing or the level is not enough.
⚫Dji pilot occasionally appears abnormal display and other phenomena, can be
solved by restarting the software;
⚫High frequency abnormal sound and vibration or vibration occur in the cradle head
shaft. If the heat is serious, please do not use it and contact the after-sales staff to
return to the factory for maintenance.

Parameters
Population parameter
The product name
Aladdin spotlight
Electrical interface
Average SKYPORT
size
100 * 110 * 150 mm
weight
470 g
Rated power
48 w
LED lights,
The LED type
CREE XHP50.2 / copper substrate
System voltage
6 v
power
40 w
Luminous flux
10200 lm
Reflective cup
Vacuum sputtering silver-plated
reflective cup; The mirror
FOV
15 °
Look into the distance
150 m
Flood area
Flight altitude: 1863m @ 120m;
Flight altitude 323m @ 50m
Actual illumination measurement
4LUX @120m flight altitude;11 lux @ 60
meters;47LUX@30 m flight altitude
Laser indicator
Laser power
5 mw
Laser eye safety rating
Class 3 a
The wavelength
620 + 10 nm
FOV
1 mrad
color
red
Gimble
Number of shaft
Three axis
Angular jitter
+ / - 0.01 °
Way to install
detachable
Control point of view
Pitch: + 90 °to 90 °,
Yaw: + 170 °
Maximum control speed
Pitch: 60 °/ s, Yaw: 60 °/ s
The cooling system
Heat sinks
is
fan
is
The environment temperature
Operating temperature
- 10 ℃to 50 ℃
Storage temperature
- 20 ℃to 60 ℃