DK2 Power OPG888E User manual

OPG888E
14 INCH STUMP GRINDER
ATV TOWABLE • 12 CUTTING TEETH • 14HP KOHLER ENGINE
ASSEMBLY GUIDE
PARTS AND SERVICE 1 [phone] | WWW.DETAILK2.COM
DK2 USA WEST
4301 S VALLEY VIEW BLVD.
SUITE 1011 LAS VEGAS, NEVADA
89103 USA
DK2 USA EAST
3750 SOUTH AVENUE,
NORTH UNIT, TOLEDO, OHIO
43615 USA
DK2 CORPORATE OFFICE
5330 MAINWAY
BURLINGTON, ONTARIO
L7L6A4 CANADA

2 | OPG888E man.
TABLE OF CONTENTS
SECTION I: ASSEMBLY ............................................................3
STEP 1: INSPECT THE PACKAGING......................................................4
STEP 2: WHEELS .....................................................................5
STEP 3: TOW BAR ....................................................................6
STEP 4: HANDLE BASE................................................................7
STEP 5: HANDLE .....................................................................8
SECTION II: SAFETY & OPERATION .................................................9
YOUR KOHLER ENGINE ..............................................................10
SAFE PRACTICES & GENERAL INFORMATION ...........................................11
QUICK START & TROUBLESHOOTING .................................................12
ADJUSTING THE DRIVE BELTS ........................................................13
SECTION III: PARTS & SCHEMATICS ................................................14
SCHEMATICS .......................................................................15
PARTS LIST .........................................................................16
WARRANTY .....................................................................17
ENGLISH

SECTION I
ASSEMBLY

4 | OPG888E man.
ASSEMBLY
CHECK THE PACKAGING
STEP 1: INSPECT THE PACKAGING
Open and unpack all items. Leave lots of working space. Inspect all parts.
The Stump Grinder is shipped in a crate. Leave the sides folded down and use as your work space.
NOTE: Upon inspection of parts, if you find any damage or missing parts please call DK2
POWER at 1 [phone] or contact us via our website at www.detailk2.com. We will
replace any damaged or missing parts to you for free. Please do not return to the store.
ENGLISH

v.211026 | 5
ASSEMBLY
STEP BY STEP INSTRUCTIONS
STEP 2: WHEELS
1. Install both wheels on the axle and secure semi-tight with the provided lock nut, allowing the
wheel to spin freely.
2. The wheel with the large brake disk mounts on the same side as the belt drive.
BRAKE WHEEL MOUNTS ON
THIS SIDE OF THE GRINDER
ENGLISH

6 | OPG888E man.
ASSEMBLY
STEP-BY-STEP INSTRUCTIONS
STEP 3: TOW BAR
Install the universal tow bar and trolley wheel to the unit. The trolley wheel can flip up and down
depending on the task.
ENGLISH

v.211026 | 7
ASSEMBLY
STEP BY STEP INSTRUCTIONS
STEP 4: HANDLE BASE
INSTALL THE HANDLE BASE
USING THE HARDWARE
PROVIDED.
ENGLISH

8 | OPG888E man.
ASSEMBLY
STEP-BY-STEP INSTRUCTIONS
STEP 5: HANDLE
INSTALL THE BOW HANDLE
USING THE LONG BOLT
AND SPIN HANDLE
PROVIDED. ALIGN THE
TEETH AND TIGHTEN.
ENGLISH

SECTION II
SAFETY & OPERATION

10 | OPG888E man.
SAFETY & OPERATION
YOUR KOHLER ENGINE
Read the Kohler engine manual supplied with your unit for full engine operation, safety, and
maintenance instruction.
1Air Filter - Summer and Winter Positions
2Choke - Left is On / Right is O (Run Position)
3Gas - Use Mid Grade or Higher
4Gas On / O Switch - Left is O / Right is On
5Throttle - Rabbit Fast / Turtle Slow
6Pull Starter - Pull Tight - Then Pull Start
7Oil - Fill to mark 10W30, will not start if oil is low, has low oil shuto
protection. Two yellow caps are oil fill caps, use either one to fill oil.
2
1
5
3
4
6
7
ENGLISH