DLS PD408-AN10-277 User manual
Digital Lighting Systems, Inc.
USER'S MANUAL
PD408-AN10-277-UM
- 10/12
PD408-AN10-277
4 circuit Analog 1-10V
4 x 8 A. Dimmer pack
Digital Lighting Systems,Inc
1-305-969-8442
www.digitallighting.com
Made in USA
Serial Number
Dimmers Indicators
4321
PD408-AN10-277
ANALOG 0-10 V
0-10V analog control
4 Channel x 2250 W Dimmer & Switch Packs
220/240/277 Volts operation
User's Manual - Page 1
RJ45 Female Connectors
Table 1 - Terminals Definition
Table 2 - Absolute Maximum
Electrical Ratings
PD408-AN10-277 Load Driver Module Information
Figure 1 - PD408-AN10-277 LDM Detail
Ground
Earth Ground
Electrical Characteristic Terminal Maximum
Relay Load Current 1 to 4 8 Amps.
Input Current For Relays 1 & 2 H1 20 Amps.
Input Current For Relays 3 & 4 H2 20 Amps.
Input Voltage H1-H2 220 to 277 VAC,
1-Phase.
NAME DESCRIPTION
1Output Of Solid-State Relay #1
2Output Of Solid-State Relay #2
3Output Of Solid-State Relay #3
4Output Of Solid-State Relay #4
H1 Hot Line Feed For Relays 1 & 2.
H2 Hot Line Feed For Relays 3 & 4.
N1-N6 Neutral Bus Connections.
INT-AN04
Control
Board
J3
LDM
SSR's OPTICAL ISOLATORS
Load Driver Module
9 VAC
Transformer
SSR1
SSR2
SSR3
SSR4
NEUTRAL BUS
1
2
N1
N2
N3
N4
N5
N6
3
4
H1
H2
Specifications:
4 x 2250 Watts @ 277 VAC dimmer pack
which is designed to be controlled either
by a 4 x100 KOHM potentiometers ; one
for each dimmer, or by a standard 0-10 V
analog signal from a sinking or
sourcing controller.
Control Input specifications:
1 mA. current; Response range :
1 V = 0% ; 10 V = 100 %
Dimmer power specifications:
Operating Voltage: 277 VAC
Input : 2 x 20 Amp Breaker on 1 phase
Outputs: 4 x 2250 Watts
PD408-AN10-277
1
INT-AN04
4 channel 0-10 V dimmer board
Logic control firing board
Figure 2 - INT-AN04 control board
2 3 4
Output indicators
1
D
S
Switch or
dimmer
jumpers
Switch level
adjustment
Each channel of the PD408-AN10-277 could be set to dim or switch.
4 Jumpers, 1 for each channel, are located on the back of the front cover.
Place jumper on D side for normal 0-10V dimmer operation, place jumper on S side for
switch operation.
Switching control Voltage level could be set from 0 to 10 V with the TrimPot.
FRONT INT-AN04 BACK
TrimPot
Dim 1Switch 1
Dim 2Switch 2
Dim 3Switch 3
Dim 4Switch 4
PD408-AN10-277-UM
- 10/12
Copyright 2012 Digital Lighting Systems, All rights Reserved Specifications are subject to change without notice. Printed in U.S.A.
12302 SW 128 Ct. ; Miami, FL 33186 Tel: 305-969-8442 [email protected]
4x 2250 W.@ 277 V Dimmer Pack
PD408-AN10-277
Digital Lighting Systems, Inc.
Analog 0-10V control
DigitalLighting.com
Enclosure Installation
Surface mount the dimmer pack in a well ventilated area where the ambient temperature does not exceed 104° F for
full load operation. Allow 2" of side clearance for proper air circulation and servicing. Installation clearance shall meet
local and/or NEC code requirements. Enclosures may be attached to the wall or other mounting surface by holes in
the heat sink flanges. Refer to the drawings below (FIGURE 3) for the correct dimensions. Conduit shall be pulled to
the top of the dimmer packs.
NOTE
The PD408-AN10-277 may create a slight buzzing noise and should not be located where this is objectionable.
User's Manual - Page 2
PD408-AN10-277 ( LDM) Load Driver Module
Figure 3 - PD408-AN10-277 Dimensional Diagram
0-10V control connectors
10 VAC
Transformer
H1 1 2 N1 N2 N3 N4 N5 N6 3 4 H2
T1
T2
T4
T3
1 2 34
1 2 34
LED's OPTO-ISOLATORS
J2J1J3
1
10
1
10
1
8
W1 W2
5" (127 mm)
LDM - Load Driver Module
5" (127 mm) PD408-AN10-277 Front Cover
8.30"
(211 mm)
Top View
2"
(51 mm)
2"
(51 mm)
4.12"
(105 mm)
1.9"
(48 mm)
1/2” and 3/4” Conduit Knockouts
2.15"
(55 mm)
2.15"
(55 mm)
LED OUTPUT
MONITORS 14
INT-AN04
11.75" (298 mm)
11.07" (281 mm)
CCCC
Bottom View
23
0-10 Volt
Input Low Voltage
Control Ports
PD408-AN10-277-UM
- 10/12
Copyright 2012 Digital Lighting Systems, All rights Reserved Specifications are subject to change without notice. Printed in U.S.A.
12302 SW 128 Ct. ; Miami, FL 33186 Tel: 305-969-8442 [email protected]
4x 2250 W.@ 277 V Dimmer Pack
PD408-AN10-277
Digital Lighting Systems, Inc.
Analog 0-10V control
DigitalLighting.com
Wiring Notes
0DO NOT EXCEED 2216 W (8 Amps.) per dimmer output @ 277 VAC.
0All wiring between the control stations, dimmers, and other system
controllers (network bus) is low voltage (NEMA Class 2)
0PD408-AN10-277 dimmer packs may be fed by one or two 20 A
(maximum) branch circuits and may have up to four separately dimmed
loads.
0Both breakers must be on the same power phase.
0CAUTION: DO NOT attempt to parallel outputs to increase capacity.
0Installations must conform to local and/or NEC code requirements.
0Each load must have its own Neutral wire for full load operation.
0All line voltage wires must have copper conductors of adequate Gauge
with 90° C wire insulation.
0POWER EACH LOAD DIRECTLY BEFORE CONNECTING IT TO THE
PD408-AN10-277 TO ENSURE PROPER WIRING.
PD408-AN10-277 General Wiring Instructions
Figure 7 - PD408-AN10-277 Typical 277 VAC Wiring.
User's Manual - Page 3
+-+-
#1
#4
+ -
Control
+ -
Analog 0-10V Control inputs
Figure 4 - PD408-AN10-277 Typical Control Wiring.
Control
Optional:
Could be also controlled with 4x 100 KOHM potentiometers .
+-+-
#2
#3
+ -
Control
+ -
Control
PD408-AN10-277-UM
- 10/12
Copyright 2012 Digital Lighting Systems, All rights Reserved Specifications are subject to change without notice. Printed in U.S.A.
12302 SW 128 Ct. ; Miami, FL 33186 Tel: 305-969-8442 [email protected]
4x 2250 W.@ 277 V Dimmer Pack
PD408-AN10-277
Digital Lighting Systems, Inc.
Analog 0-10V control
DigitalLighting.com
2x20 A -
220/240/277 VAC
Breakers
On Same Phase
Electrical
Distribution Panel
To Distribution Panel
Neutral Bus
LOAD #4
LOAD #3
LOAD #2
LOAD #1
ON
INT04
Control
Board
Load Driver Module
LDM
NEUTRAL BUS
1
2
N1
N2
N3
N4
N5
N6
3
4
SSR1
SSR2
SSR3
SSR4
H1
H2
SSR's OPTICAL ISOLATORS
9 VAC
Transformer
J3
ON
For Full Load Operation Use:
#12 AWG copper conductor wire for Line & Neutral Feeds.
#14 AWG copper conductors in/out to each load.
Max. Load: 8 Amperes per output.
Earth Ground
20 Amps Max.
20 Amps Max.
Digital Lighting Systems, warrants to the purchaser that its
products have been carefully manufactured and inspected and
are warranted to be free from defects of workmanship and
materials when used as intended. Any abuse or misuse contrary
to normal operation shall void this warranty.
Digital Lighting Systems' obligation under this warranty shall be
limited to replacement or repair of any units as shall within two
years of date of invoice from Digital Lighting Systems, prove
defective; and Digital Lighting Systems shall not be liable for
any other damages, whether direct or consequential. The
implied warranties of merchantability and fitness for a
particular purpose are limited to the duration of the
expressed warranty. Some states do not allow the exclusion of
the limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, you may also have other
legal rights which vary from state to state.
Defective merchandise may be returned to Digital Lighting
Systems, prepaid, after prior notification has been given and
approval obtained for the return. To obtain prior approval for the
return of the defective items, contact your local Digital Lighting
Systems distributor, representative, or:
Digital Lighting Systems, Inc.
Attn: Customer Service Department
12302 SW 128 Ct. Bay #105
Miami, FL 33186
(305) 969-8442
Upon request, replacement unit(s) will be shipped as soon as
available. Unless immediate shipment of replacement
merchandise is requested, Digital Lighting Systems will not
ship replacement merchandise until defective merchandise is
received, inspected, and determined to be defective.
No labor charges in connection with warranty problems will
be reimbursed by Digital Lighting Systems without prior
written approval from the factory.
Digital Lighting Systems distributors and representatives have
no authority to change this warranty without written permission.
Digital Lighting Systems reserves the right to determine the
best method of correcting warranty problems.
LIMITED WARRANTY
Digital Lighting Systems, Inc.
12302 SW 128 Ct. Bay #105
Miami, FL 33186
www.digitallighting.com
Tel 305-969-8442
Fax 305-969-8675
Printed in U.S.A.
December 2012
Table of contents
