DMP Electronics V-4061DB User manual

V-4061DB VIDEO DOORBELL
Installation Guide
DESCRIPTION
Figure 1: V-4061DB
The V-4061DB is a Wi-Fi enabled
video doorbell capable of of
recording and storing video clips
that are viewable on the Virtual
KeypadTM App.
The V-4061DB provides 16 GB of
storage on a pre-installed SD card
for local recording.
Compatibility
• Virtual Keypad™ App 6.33.4
or higher for iOS and Version
6.37.0 for Android devices
What is Included?
• V-4061DB Video Doorbell
• Pre-installed 16 GB SD card
• 4 dierent color faceplate
options
• Power Kit
• Fuse and Screw Pack
• Vertical, Horizontal, and Flat
Wedges
• Weather Gasket
• Reversible Screwdriver
• Phillips Head
• Security Screw Bit
1PREPARING VIDEO DOORBELL FOR
INSTALLATION
1. The V-4061DB can be installed in place of a functional,
wired, 16-24VAC mechanical doorbell system, or with a 16-
24V wired transformer.
2. Once you have confirmed that the existing doorbell works,
shut o doorbell’s power at the breaker.
21. Remove the existing doorbell from the wall, leaving the
existing wiring exposed.
2. Remove the security screws securing the faceplate to the
doorbell, then carefully remove the faceplate.
Note: The included screwdriver has a reversible head. The
star bit is used to remove the security screws from the
doorbell faceplate, and the Phillips-head bit is used for
installing the screws on the back of the doorbell.
3. Hold the doorbell flat against the wall where the old
doorbell was and mark the screw hole locations.
4. Drill the holes using the marks you made as a guide.
5. In the screw hardware pack, locate the screw used to
tighten down the wires and loosely attach these screws to
the back of the doorbell. It does not matter which wire is
connected to which screw.
Note: If you are using a 16-24V plug-in transformer to power
the doorbell, be sure to attach the included fuse to either
wire during installation. The fuse is not needed if the
doorbell is being connected to a standard 16-24V
mechanical doorbell chime.
6. Use the included screws to secure the doorbell to the wall.
Replacing Existing Doorbell
INSTALLING THE VIDEO DOORBELL
Figure 2: Video Doorbell
Layout
Lens
Microphone
PIR Motion Detector
Ring Button

2 V-4061DB VIDEO DOORBELL | DIGITAL MONITORING PRODUCTS
1. Log in to dealer.securecomwireless.com.
2. Select the appropriate system for the V-4061DB Video Doorbell.
3. On the System Information screen under Add-On Features, check the Video Doorbell box. This will
allow the doorbell to sync with the Virtual Keypad App.
ENABLE THE VIDEO DOORBELL IN DEALER ADMIN
4
Existing Chime
Front
Trans
Rear
Power Kit
Chime Wire
Chime Wire
Figure 3: Installing the Power
Kit
If you are not installing the doorbell with an existing mechanical chime, skip to section 4.
1. With the breaker supplying power to the mechanical chime still o, remove the cover from the
mechanical chime.
2. Loosen the TRANS terminal and connect the existing chime wire to the power kit wire using the
included wire nut.
3. Loosen the FRONT terminal and connect the existing chime wire to the power kit wire using the
included wire nut.
4. Connect the wire harness to the TRANS terminal and tighten it down.
5. Connect the other wire harness to the FRONT terminal and tighten it down.
6. Insert the white wire connector into the power kit.
7. Mount the power kit within the mechanical chime housing using the adhesive backing and replace the
cover.
8. Turn on the breaker to the part of the home where the video doorbell and mechanical chime are
installed.
3INSTALLING THE POWER KIT

V-4061DB VIDEO DOORBELL | DIGITAL MONITORING PRODUCTS 3
The video doorbell requires a 2.4 GHz Wi-Fi signal.
1. Ensure that you know the Wi-Fi SSID and password that you wish to connect the doorbell to.
2. Log into the Virtual Keypad app and go to the Doorbell tab.
3. Tap Set Up Doorbell.
4. Tap Scan Doorbell and scan the QR code located underneath the faceplate on the front of the
doorbell.
5. When the QR code is confirmed, press Configure Wi-Fi.
6. Enter the SSID and password for the Wi-Fi network that the doorbell is connecting to and press
Continue.
7. Use your device to connect to the doorbell’s Wi-Fi network.
For Andriod Users:
Virtual Keypad will attempt to automatically connect to the doorbell’s Wi-Fi network and configure
the Wi-Fi information for you. This may take a few seconds.
For iOS Users:
Copy the doorbell’s Wi-Fi password, then navigate to the Wi-Fi settings on your phone. The
doorbell will transmit an SSID for your phone to use. The SID will be HAP followed by the doorbell’s
serial number. For example, if the doorbell serial number is “12345678” then the SSID that the
doorbell transmits would be “HAP_12345678.” Paste the password to connect to the doorbell’s Wi-
Fi network.
Note: The password will be “AP” followed by the verification code. For example, if the verification
code is “ABCDEF”, then the password would be “APABCDEF.”
8. Navigate back to the Virtual Keypad app. Press Continue. When the network pairing has been
confirmed the doorbell will announce that it is connected to Wi-Fi.
9. Give the doorbell a name. You will be prompted to select the type of chime the doorbell is using.
Select Mechanical Chime when installing the video doorbell with a standard 16-24V mechanical
doorbell chime. Select No Chime when installing the video doorbell with a 16-24V plug in
transformer. If No Chime is selected, make sure you have installed the included fuse. The V-4061DB
is not compatible with digital chimes.
10. Press Finish to complete the installation. It could take up to a minute for Virtual Keypad to
finsh configuring your doorbell. When it has been successfully configured, Virtual keypad will
automatically launch into the live view.
After the doorbell has been set up in the Virtual Keypad app and after obtaining the IP address that your router has
assigned to the doorbell, follow the NVR manufacturer recommended steps to add a camera to an NVR.
1. Choose Manual mode to add a camera.
2. Enter the IP address.
3. Set the protocol to Hikvision.
4. Leave the Management Port at the default 8000, the Channel Port as the default 1, and the TransferProtocol as
the default Auto.
5. The username is “admin”. The password is the verification code that is on the back of the doorbell. As an example,
if the verification code is ILGWQM then the password would be ILGWQM.
CONNECTING THE DOORBELL TO AN NVR
ADDITIONAL INFORMATION
CONNECT VIDEO DOORBELL TO WI-FI USING VIRTUAL KEYPAD APP
5

LT-2524 21183
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
800-641-4282 | DMP.com
© 2021
V-4061DB VIDEO DOORBELL
Specifications
Sensor and Lens:
Image Sensor 2MP
Lens 2.4mm, F.2.25
Field of View 170 degrees (Vertical),
105 degrees (Horizontal)
Video Compression H.264
Frame Rate 15 Frames per Second
IR Distance 25 ft
Network:
Wireless Compatibility 2.4 GHz
Storage:
On-Board Storage 16 GBSD card installed (Supports up to 128 GB)
Hardware:
Power Required 16 VAC to 24 VAC
Power Consumption Max 5w
Working Temperature -22 F to 122 F (-30 C to 60 C)
Dimensions (HxWxL) 1.8” W x 5.4” H x 0.82” D
Compatibility
Virtual Keypad App Version 6.33.4 or higher for iOS devices
Virtual Keypad App Version 6.37.0 for Android devices
Accessories
V-4061DB-PK Power Kit
V-4061DB-WEDGE Wedge Kit
1. Delete the doorbell from the Virtual Keypad App. To delete a doorbell, tap the Menu icon and select Doorbell. Tap
the Edit icon, the tap Delete.
2. Remove the doorbell’s cover and hold down the reset button for 25 seconds or until the doorbell audibly states,
“doorbell is rebooting.” The doorbell will go through its reboot process and announce when it is ready to be
reconfigured.
3. Repeat instructions in Connect Video Doorbell to Wi-Fi Using Virtual Keypad App.
LED COLOR DESCRIPTION
Solid Red The doorbell is turning on or rebooting
Flashing Red The doorbell is preparing for configuration
Quickly Flashing Blue The doorbell is ready to be added using Virtual Keypad
Slowly Flashing Blue The doorbell is connected to Wi-Fi
CHANGING SSID OR PASSWORD
Figure 4: LED Color Descriptions