DNF Controls ST300-SRP User manual

12843 Foothill Blvd. Suite C
Sylmar, California 91342
V: 818.898.3380
F: 818.898.3360
[e-mail]
Model No. ST300-SRP
and ST300-SRP-T
for
DDRs With Simultaneous
Record/Playback Capability
SLOW MOTION CONTROLLER
USER MANUAL
V 1.41

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 2
2 o of f 2 23 3
Table of Contents
1. REVISION HISTORY 3
GETTING STARTED . . . 4
2. SYSTEM DESCRIPTION 4
DEFINITIONS 4
3. INSTALLATION 5
a. SIMULTANEOUS RECORD/PLAYBACK MODE OFF 5
b. SIMULTANEOUS RECORD/PLAYBACK MODE ON 5
4. OPERATION 7
a. LCD DISPLAY 7
b. TRANSPORT CONTROL 7
c. CUE POINTS 8
d. GOTO/PREROLL TO A MANUALLY ENTERED TIME 9
e. RECORD MODE SELECTION 9
5. SIMULTANEOUSRECORD/PLAYBACK FUNCTIONS 10
a. SELECT SIMULTANEOUS RECORD/PLAYBACK MODE 10
b. CREATE NEW CLIP 10
b. STOP RECORD 11
c. GO TO EE 11
d. GOTO LIVE 11
ADVANCED FEATURES . . . 12
6. TRANSFER CUELIST 12
a. TRANSMIT CUE LIST FUNCTION 12
b. RECEIVE CUE LIST FUNCTION 13
REFERENCE . . . 14
7. SETUP MENU 14
8. FUNCTION TABLE 17
9. SPECIFICATIONS 20
RS422 SERIAL CONNECTOR 20
POWER CONNECTOR 20
AUX PORT RS422 SERIAL CONNECTOR 21
GPI IN/OUT CONNECTOR 21
10. KEY LAYOUT 22
11. DNFCONTROLS LIMITED WARRANTY 23
Manual Version:.......……….....................................1.41 091906
Document ID:....….….…….........ST300-SRP_User_Manual.doc

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 3
3 o of f 2 23 3
1. REVISION HISTORY
051603 1.0 Original document
123003 Rev. 1.1 Company header information revised.
Updated Transmit Cue List Function and Receive Cue List Function
Descriptions.
Added DNF Controls Limited Warranty.
060204 Rev. 1.2 Updated Connection Diagram.
Corrected T-bar size, SPECIFICATION.
111804 Rev. 1.3 Added GOTO LIVE Section.
Added Video Standard Selection and
INPUT Video Delay Entry to SETUP MENU.
102605 Rev. 1.4 Update to current manual convention
091906 Rev. 1.4 1 Update to include Create New Clip function.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 4
4 o of f 2 23 3
Getting Started . . .
2. SYSTEM DESCRIPTION
The ST300-SRP Slow Motion Controller combines the power of the ST300 Slow Motion
Controller with the power of DDRs that have simultaneous record/playback capability.
In the ST300 Setup Menu, disable S-RP Mode to access standard ST300 Slow Motion functions.
Enable SRP Mode to access the following functions:
Simultaneous Record and Playback.
Press [EE] to go to live video.
DEFINITIONS
Throughout this document VTR, DDR, VDR & Video Server will be referred to collectively
as “VTR.”
The ST300-SRP will be referred to as “ST300.”
Words surrounded by brackets, for example, [ENTER], are keys on the ST300.
Words surrounded by curly brackets, for example, {DEFAULTS}, are soft keys under the
display.
[XXX] + [XXX] means hold the two keys down simultaneously.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 5
5 o of f 2 23 3
3. INSTALLATION
Select a. OR b. below.
a. SIMULTANEOUS RECORD/PLAYBACK MODE OFF
1) Plug one end of a 9-conductor, RS422 serial cable into the VTR1, VTR2, VTR3,
OR VTR4 connector on the rear of the SLOW MOTION CONTROLLER. Plug
the other end of the cable into the 9-pin REMOTE connector on the VTR.
2) Connect the supplied POWER SUPPLY, APX#4108, into the POWER
connector on the rear of the ST300. Plug the Power Supply into an outlet, 90
VAC – 240 VAC.
3) Select REMOTE mode on the VTR's front panel.
4) Check the SETUP MENU prior to using the Slow Motion Controller to confirm
proper Record mode, SLO-MO speed range, and other User settable modes.
OR
b. SIMULTANEOUS RECORD/PLAYBACK MODE ON
1) Connect VTR1 connector on the back of the ST300 to the REMOTE connector
of playback channel on DDR 1.
2) Connect VTR3 connector on the back of the ST300 to the REMOTE connector
of record channel on DDR 1.
3) Connect VTR2 connector on the back of the ST300 to the REMOTE connector
of playback channel on DDR 2.
4) Connect VTR4 connector on the back of the ST300 to the REMOTE connector
of record channel on DDR 2.
5) Connect the supplied POWER SUPPLY, APX#4108 into the POWER connector
on the rear of the ST300. Plug the Power Supply into an outlet, 90 VAC – 240
VAC.
6) Select REMOTE mode on the DDR’s front panel.
7) Check the SETUP MENU prior to using the Slow Motion Controller to confirm
proper Record mode, SLO-MO speed range, and other User settable modes.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 6
6 o of f 2 23 3

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 7
7 o of f 2 23 3
4. OPERATION
a. LCD DISPLAY
During normal operation, the top row of the display shows the selected time mode
and current time location of the selected VTR.
For example: TM 01:12:09:23
Time Modes - TM= Tape Timer TC= LTC VT= VITC
The currently selected SLO-MO speed is displayed on the far right side of the
top row.
The bottom row of the display shows the current Cue Point number
and its contents.
b. TRANSPORT CONTROL
Select the desired transport function by pressing the appropriate switch on the SLOW
MOTION CONTROLLER.
The Real-Time Status Indicators will light to indicate the VTR's current tape transport
mode.
For example: Pressing [PLAY] will put the VTR into the PLAY mode.
The PLAY Status Indicator will turn on when the VTR is in PLAY
mode.
Press [RECORD].
OR
[RECORD] + [PLAY] to put the VTR into Record mode (see SETUP
MENU).
NOTE: The VTR will not go into Record mode if “Record Inhibit” is enabled
on the VTR or tape cassette.
Check SETUP MENU prior to using the SLOW MOTION
CONTROLLER to confirm proper Record mode and other User
settable modes.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 8
8 o of f 2 23 3
c. CUE POINTS
1) Select a Cue Point
Press [NEXT CUE] or [LAST CUE] to step through the Cue Points.
OR
Manually enter the desired Cue Point number using the numeric keypad.
The current Cue Point number and its contents will be shown on the second line
of the display.
2) Mark/Enter/Edit a Cue Point
Press [MARK] to mark the VTR’s time into the Cue Point.
OR
Press [ENTER TIME] to use the numeric keypad. The ENTER TIME
indicator will turn on.
Manually enter a time on the numeric keypad. Press [ENTER] to save the
entered time.
OR
Press [ESC] to exit without saving. The ENTER TIME indicator will turn off.
3) Goto/Preroll to a Cue Point
a) Select the desired Cue Point. The Cue number and its contents are
shown on the bottom line of the display.
b) Press [GOTO] to search to the Cue Point; the GOTO indicator will
turn on. When the VTR reaches the Cue Point time, the GOTO
indicator will turn off.
OR
Press [PREROLL] to preroll to the Cue Point. The PREROLL
indicator will turn on.
When the VTR reaches the Cue Point time, the PREROLL indicator
will turn off.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 9
9 o of f 2 23 3
d. GOTO/PREROLL TO A MANUALLY ENTERED TIME
1) Press [ENTER TIME] to use the numeric keypad.
Manually enter a time on the numeric keypad.
2) Press [GOTO] to search to the entered time.
OR
Press [PREROLL] to search to the entered time minus the preroll time.
OR
Press [ESC] to exit without searching.
The ENTER TIME indicator will turn off.
e. RECORD MODE SELECTION
1) Press [MENU]. The MENU indicator will turn on.
2) Turn the Wheel until “REC” is viewed on the top line of the display. The
current Record mode is shown.
3) Press [MENU] to select:
Record Lockout, Assemble, Crash or Insert Record mode.
4) INSERT ONLY - Press the desired Softkey to toggle {Video}, {Audio1},
{Audio2}, {Audio3}, or {Audio4} record on/off.
The Softkeys are located just below the display.
Follow the line graphic from the bottom of the display to the Softkey.
5) Press [ESC] to exit the MENU. The MENU indicator will turn off.
OR
Turn the Wheel for other setup options.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
10 0 o of f 2 23 3
5. SIMULTANEOUS RECORD/PLAYBACK FUNCTIONS
a) SELECT SIMULTANEOUS RECORD/PLAYBACK
MODE
1) Press [MENU] key.
2) Turn the wheel until the display shows “Simult. REC/PB:”
3) Press {ON} softkey to turn Simultaneous Record/Playback mode ON. In this
mode, Recorder and Player channels of a DDR are treated as one VTR.
[VTR3] and [VTR4] keys are disabled in this mode.
Refer to Installation, Section 3, for connection information.
When this mode is OFF the controller behaves as a standard ST300 VTR
controller.
4) Press [ESC] key to exit menu.
b) CREATE NEW CLIP
Prior to the start of the recording you must open a file on the DDR record channel. Each
file (channel) must be given a unique name. Once the channels have been put into
record, the clips need to be loaded on the corresponding play channel of the DDR.
1) Create a clip on the video server using local controls on the server unit. This
opens a file ready for recording.
Do not start the record process at this time. Use the record function on
the ST300 when you are ready to actually start recording.
2) Create a clip on each record channel of the video server.
c) START RECORD
NOTE: For some DDRs, create clip first.
1) Press [SHIFT] + [REC] on VTR1 to start recording on the Record channel
connected to VTR3 connector on the rear of the ST300.
2) The Record LED turns ON.
3) Press [SHIFT] + [REC] on VTR 2 to start recording on the Record channel
connected to VTR4 connector on the rear of the ST300.
4) The Record LED turns ON.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
11 1 o of f 2 23 3
d) STOP RECORD
1) Press [SHIFT] + [STOP] on VTR1 to stop recording on the Record channel
connected to VTR4 connector on the rear of the ST300.
2) The Record LED turns OFF.
3) Press [SHIFT] + [STOP] on VTR2 to stop recording on the Record channel
connected to VTR4 connector on the rear of the ST300.
4) The Record LED turns OFF.
e) GO TO EE
Press [EE] key to go to Live video on the corresponding Playback Channel. The EE
LED turns on.
f) GOTO LIVE
1) Press [REC] key.
2) The Player searches to the current Recorder time minus user-defined INPUT
Video Delay (see SETUP MENU).
3) The Player starts playing.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
12 2 o of f 2 23 3
Advanced Features . . .
6. TRANSFER CUELIST
a. TRANSMIT CUE LIST FUNCTION
The TRANSMIT CUE LIST function allows you to transmit your list of Cue Points to a
PC, using the provided utility software on the PC, or to another ST300. Transfer to a PC
requires OpSuite 3.0 software, which runs on a Windows-based computer. Contact DNF
Controls for more information.
1) To Transmit Cue Points to another ST300
a) Connect the VTR4 connector on the rear of the ST300 to the VTR4
connector of the receiving ST300 using an RS422 9-pin cable with TX
and RX lines crossed. (A “turnaround” cable.)
b) Press [MENU].
c) Scroll the Wheel until “Transmit CUE list? YES=Enter, Exit=ESC” is
displayed.
d) Press [ENTER] to start transmitting. The Display shows “Waiting to
transmit” on the first line.
e) When the Receiver is ready, transfer starts automatically. The Display
now shows “Transmitting cuelist.”
f) After the transfer is over, the display shows “Transfer is over” for one
second and then shows “Waiting to transmit” again.
g) Connect another ST300 to transmit the list again.
OR
Press [ESC] twice to exit the MENU mode.
2) To Transmit Cue Points to a PC
a) Connect the VTR4 connector on the back of the ST300 to one of the
COM ports on the PC using a RS422 to RS232 adapter.
b) Repeat steps a) thru g) of “To Transmit Cue Points to Another
ST300,” Section 6.a.1).

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
13 3 o of f 2 23 3
b. RECEIVE CUE LIST FUNCTION
The RECEIVE CUE LIST function allows you to receive a list of Cue Points from a PC
or from another ST300. Transfer to a PC requires OpSuite 3.0 software, which runs on a
Windows-based computer. Contact DNF Controls for more information.
1) To Receive Cue Points From Another ST300
a) Connect the VTR4 connector on the back of the ST300 from the VTR4
connector of the transmitting ST300 using RS422 9-pin cable with TX
and RX lines crossed.
(A “Turnaround” Cable)
b) Press [MENU].
c) Scroll the Wheel until “Receive CUE List? YES=Enter, Exit=ESC” is
displayed.
d) Press [ENTER] to start receiving.
The Display shows “Waiting to receive” on the first line.
e) When the Transmitter is ready, transfer starts automatically. The
Display now shows “Receiving cuelist.”
f) After the transfer is over the display shows “Done-Success! Press any
key…”
g) Press any key. The display shows “Receive cuelist?” message.
h) Press [ESC] to exit the MENU mode.
2) To Receive Cue Points from the PC
a) Connect the VTR4 connector on the back of the ST300 to one of the
COM ports on the PC using RS422 to RS232 adapter.
b) Repeat steps a) thru h) of “To Receive Cue Points From Another
ST300,” Section 6.b.1).

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
14 4 o of f 2 23 3
Reference . . .
7. SETUP MENU
Press [MENU]. The MENU indicator will turn on. Turn the Wheel to select item to change.
Use the Softkeys to change the desired mode for that option. Turn the Wheel at anytime to
select another item.
Press [ESC] at anytime to exit SETUP MENU. The MENU indicator will turn off.
MENU MODES
(Turning Wheel Clockwise)
RECORD Press [MENU] to select the desired record mode:
Lockout, Assemble, Crash (Full) or Insert.
Only in INSERT mode: Press the associated Softkey, located below the display, to toggle
Video{V}, Audio1{A1}, Audio2{A2}, Audio3{A3}, Audio4{A4} on/off.
MARK-Q Press Softkey to:
Enable {ADVANCE} to next Cue Point, when [MARK] is pressed.
OR
Maintain {CURRENT} Cue Point when [MARK] is pressed.
SIMULTANEOUS
RECORD/
PLAYBACK
Press Softkey to select:
Simult. Rec/PB {OFF} ST300 works like the standard ST300 and does not use
special functions
Simult. Rec/PB {ON} ST300 uses Special Simultaneous Record/Playback functions.
Connect ST300 to DDR using Simultaneous
Record/Playback Mode ON Connection Diagram.
WIND MODE Press Softkey to select:
{HOLD} (Fast wind is maintained only while key is pressed.)
OR
{LATCH} (Fast wind is initiated and maintained with momentary key press.)
S
Se el le ec ct t f fa as st t w wi in nd d s sp pe ee ed d ( (3 3. .9 9 t to o 2 23 3. .7 7) ) b by y p pr re es ss si in
ng g S So of ft tk ke ey y b be el lo ow w { {S SP PD D} }. .

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
15 5 o of f 2 23 3
SLOMO
ST300 display shows
(Tbar version):
ST300 display shows
(Non T-Bar version):
Press Softkey {TBAR} or {WHEEL} to toggle between T-BAR and WHEEL.
The T-BAR has two speed ranges:
0 Æ+200 with a detent at +100 % play speed
OR
0 Æ+100 with a detent at +100%
For Wheel only:
Press Softkey {SPDRANGE} to select SLOMO speed ranges:
Press Softkey to select: {0
Æ +200} OR {-100 Æ +200}.
Press Softkey {BACK} to return to SLOMO MENU.
Press [ESC] to exit SETUP MENU
OR turn the Wheel to select another item.
For Wheel only:
Press Softkey {PRSET} to select the SLOMO Preset Speed Mode.
Press Softkey {UPDATE}.
When exiting SLOMO mode, the last used speed is saved in the Preset Speed register.
Press Softkey {STATIC}.
The Preset Speed register is NOT updated when exiting SLOMO mode.
It is only changed by [SHIFT] + [SLOMO] (PRESET SLOMO).
TBAR
AUTOENABLE Press Softkey {ON} to enable slomo to be engaged by moving the TBAR.
SLOMO with: WHEEL
SpdRange Preset
SLOMO with: TBAR
Wheel SpdRange Preset

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
16 6 o of f 2 23 3
WHEEL
AUTOENABLE Press Softkey {JOG} or {SHUTTLE} to enable that function to be engaged by turning the
Wheel.
VIDEO
STANDARD Press softkey to select {NTSC}, {PAL} or {24P} video standard, depending on the standard
you are using.
GANG MODE Press Softkey to select {PERMANENT} GANG (described in the FUNCTION Table) or
{TEMPORARY} GANG.
In TEMPORARY mode, press and hold the VTR key that you want to read status from,
then press the VTR#s of those VTRs that you want to include in the gang. Release the
keys. The LED on the monitored VTR blinks, all other VTRs in the gang stay on
constantly. To break the temporary gang, press any VTR# key.
ST300 SETUP
Press Softkey beneath {ClearCues} to clear all Cue Points to 00:00:00:00.
Press Softkey {YES} when asked “Are You Sure?” or {NO} to exit without clearing cues
Press Softkey beneath {SetDefault} to set ST300 to default settings.
Press Softkey {YES} when asked “Are You Sure?” or {NO} to exit without setting
defaults.
DISPLAY
SOFTWARE
VERSION
The version number for the currently installed software is displayed.
DROP FRAME Press Softkey to select DROP FRAME {ON} or {OFF}.
Used to preset the VTR’s Timecode Generator.
RECORD KEY Press Softkey to select single button or 2-button record.
RECORD = {REC} Only
OR
RECORD = {REC + PLAY}
FREEZE Press Softkey {YES} to enable or {NO} to disable FREEZE at Record Outpoint. Changing
mode automatically clears FREEZE point.
INPUT VIDEO
DELAY Input Video Delay specifies the time interval between video recorded on the Recorder parts
being available for playback. This parameter is used in GOTO LIVE function.
The default value is 5 seconds.
TRANSMIT
CUELIST Transmits Cuelist to another ST300 or to a PC.
See section 6a.
RECEIVE
CUELIST Receives Cuelist from another ST300 or a PC.
See section 6b.
ST300 SETUP
Clear Cues SetDefaul
t

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
17 7 o of f 2 23 3
8. FUNCTION TABLE
Function Key Press Description
EE On/Off [EE] Toggle EE mode on/off. Status indicator is on when EE is on.
EJECT TAPE [SHIFT] + [REWIND] Eject tape from VTR.
ENTER TIME [ENTER TIME] To manually enter timecode number into the currently
displayed Cue Point, enter the desired timecode number using
the numeric keypad. Press [ENTER] to save your entry OR
[ESC] to exit without saving.
To enter a GOTO location without altering the contents of the
Cue Point, enter the desired timecode number using the
numeric keypad. Press [GOTO] to search to the entered time.
Press [ESC] to exit without searching.
S-RP GOTO EE [EE] Press [EE] to view live video.
S-RP START
RECORD [SHIFT] + [RECORD] Press [SHIFT] + [RECORD] to start recording on selected record channel.
S-RP STOP
RECORD [SHIFT] + [STOP] Press [SHIFT] + [STOP] to stop recording on the selected record channel.
FFWD [FFWD] Press and HOLD to FFWD. Release key to stop. Set WIND
Speed in MENU.
FREEZE
ENABLE
[FREEZE] Toggles the Freeze on/off. When the light is ON, the Freeze
is enabled. When the light is OFF, the freeze is disabled.
NOTE: This is NOT a REC OUT freeze, it IS a user defined
Freeze.
FREEZE [SHIFT] + [FREEZE]
(Active in SLO-MO only).
To enter or mark the Freeze time, press [SHIFT] +
[FREEZE]. The display shows the current freeze time. You
can enter the Freeze time using the numeric keypad or
MARK the current time into the Freeze time by pressing
[MARK].
FREEZE ON
LAST GOOD
VIDEO
Active in SLO-MO only. In SLO-MO mode, STILL frame the VTR when the current
timecode is within 6 frames of the last Record Out point
(memorized automatically upon exiting Record mode).
Enable, disable, or clear the FREEZE point from SETUP
MENU. See FREEZE ENABLE.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
18 8 o of f 2 23 3
Function Key Press Description
GOTO CUE
or
ENTERED
TIME
[GOTO] Search the VTR to the contents of the currently displayed Cue
Point. If ENTER TIME is active (LED is on), search the
VTR to the entered time.
To enter a GOTO location without altering the contents of the
Cue Point, press [ENTER TIME]. Enter the desired
timecode number using the numeric keypad. Press [GOTO]
to search to the entered time. Press [ESC] to exit without
searching.
GANG [SHIFT] + [VTR#1]
OR
[SHIFT] + [VTR#2]
OR
[SHIFT] + [VTR#3]
OR
[SHIFT] + [VTR#4]
NOTE : Gang mode = Permanent (See menu setup).
Individually press the VTR keys to be included in the gang;
the LED above the key will turn on. Press the VTR key again
to remove from gang; the LED above the key will turn off.
Press [ESC] to exit.
The VTR LEDs that are on show the gang.
The flashing LED shows which VTR is currently selected.
GO TO FREEZE
POINT [SHIFT] + [GOTO] Search VTR to FREEZE point (last Record Out point).
JOG [JOG] Select JOG mode and enable the Wheel.
LAST CUE [LAST CUE] Step to the previous Cue Point Location.
MARK CUE
POINT [MARK] Save the current time in the currently displayed Cue Point. Per SETUP MENU, the Cue Point Location will advance to
the next Cue Point location or remain the same.
NEXT CUE [NEXT CUE] Step to the next Cue Point Location.
PREROLL [PREROLL] Preroll the VTR to the contents of the currently displayed Cue
Point.
PREROLL
VALUE [SHIFT] + [PREROLL]
Enter desired Preroll Value. Press [ENTER] to save entry
OR press [ESC] to exit without saving entry.
RECORD [REC] or
[REC] + [PLAY]
Places VTR in the Record mode selected by RECORD
MODE in the SETUP MENU.
REVERSE
PLAY
[REV] For T-BAR ONLY – HOLD key to play video in reverse.
RELEASE key to play forward.
REWIND
[RWD] Press and HOLD to rewind. Release key to stop. Set WIND
Speed in MENU.
SHUTTLE [SHUTTLE] Select SHUTTLE mode and enable the Wheel.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 1
19 9 o of f 2 23 3
Function Key Press Description
SLOMO
[SLOMO] Press SLOMO to slo-mo the VTR. Turn the Wheel or move
the T-Bar to change the play speed.
Press SLOMO to STILL frame OR press any transport key to
exit.
SLO-MO
SPEED PRESET [SHIFT] + [SLOMO] For WHEEL ONLY - to preset the slo-mo speed. Turn the Wheel to select desired speed.
Press [ESC] OR any transport key to exit.
STOP [STOP] Press once to STILL frame VTR.
Press again to put VTR into STOP mode.
TIME MODE
SELECT [TIME MODE] Press to toggle between Timecode (TC), VITC (VT) or Tape Timer (TM) display modes.
TIME PRESET
(Generator
Preset)
[SHIFT] + [TIME MODE] Press to enter Time Preset.
Press [ENTER] to load Time Generator with 00:00:00:00.
OR enter the time desired via the numeric keypad and press
[ENTER] to load that time.
OR press [ESC] to exit without saving.

ST300-SRP & ST300-SRP-T, Slow Motion Controller Page 2
20 0 o of f 2 23 3
9. SPECIFICATIONS
Power: 90 VAC to 265 VAC adapter supplied with IEC connector
Size: (L” x W” x H”) 12” x 6” x 1.5” (front) 3.0” (rear)
(T-Bar unit is 12.6” long)
Weight: 4 lbs.
Rear Panel Connectors: VTR1, VTR2, VTR3, VTR4 ……. (All DB9F)
GPI ………………………………. (DBF15F)
Power ……………………………. (DB9M)
Aux ………………………………. (DB9F)
Reference Video …………………. (BNC)
Display: Easy to read 2-line, back-lit LCD display
(User adjustable contrast)
Jog/Shuttle Wheel With mechanical detents
Optional “T”-bar Slo-mo 0-200% of Play Speed
RS422 SERIAL CONNECTOR
9-Pin D-Type, Female (DB9F)
Pin # 1 Frame Ground 6 Receive Common
2 Receive A Í7 Receive B Í
3 Transmit B Î8 Transmit A Î
4 Transmit Common 9 Frame Ground
5 Spare
POWER CONNECTOR
9-Pin D-Type, Male (DB9M)
Pin # 1 +5v DC 6 +5 VDC
2 +5v DC 7 Ground
3 Ground 8 Ground
4 +12 VDC 9 Ground
5–12 VDC