Do Beauty Starter Lizzy ND602 User manual

Product Manual
Star ter Lizzy ~ Electric Nail Drill
(ND602)

The Lizzy Electric Nail Drill is perfect qualified of nail technicians. It is a manicuring tool that is
made with a hand piece and replaceable bits. The use of a nail drill permits one to create a really
perfect nail trimming conveniently and efficiently as soon as the rotating bits are lightly carried out
to the nails, inclusive of the facet walls and cuticles. It also has a foot pedal and can be used by a right
or left-handed person. It can be used for all aspects of nail care such as manicures, pedicures, nail art
and artificial nails.
FEATURES
02
OVERVIEW
nEasy to Operate with Speed Control Knob
nForward and Reverse Switch
nSmooth, low vibration, quiet operation
nCan be used for natural nails as well as artificial nails
nIncludes Hand Piece
nIncludes Foot Control Pedal
nStylish and compact, takes up less room than most
drills
nInnovative design for professional use manicure,
pedicure, and artificial nails
nHigh torque and clean operation up to 25,000 rpm
nColet chuck type
nAluminum and chrome steel go with the flow frame.
nLow vibration
nLight weight
PARTS
n1 x Nail Drill Unit
n1 x Handpiece
n1 x Handpiece Holder
n1 x Manual
n6 x Optional Bits with 6 Sanding Band
n1 x Foot Pedal
nPower Plug

03
HOW TO USE YOUR DRILL
CHANGING THE DRILL BIT
1. Open the hand-piece chuck by turning the handle counterclockwise.
1. Start with nail sidewalls. Get a cone bit and make sure it rotates in the opposite direction to your
hand movement. It is advisable to use it at 10,000-12,000 RPM speed.
2. Using the same bit, move from the sidewalls to the bottom of your nail, gently pushing cuticle
from the nails. Hold a headpiece just as if you held a pen in hand.
3. Gently remove cuticle with a small diamond barrel bit (use it at the 45° angle at 10,000 RPM
speed).
4. Use a sapphire bit to remove excess cuticle. The recommended speed is 12,000 RPM.
5. Do not forget to apply the moisturizer after shaping, polishing, and buffing your nails.
2. Change the drill bit.
3. Lock the hand-piece chuck by turning the handle clockwise.

04
PRECAUTIONS
nKeep the area around hand-piece free from dust and grindings.
nWipe away dust from around the hand piece. You can wipe over with isopropyl alcohol. Avoid
liquids from penetrating into internal components.
nDo not apply oil to any part of the device or clean with water.
nDo not apply strong air pressure to clean the hand-piece.
SPECIFICATIONS
nMaterial: Aluminium
nInput Voltage: 100V-120V,60Hz, 220V-240V,50Hz
nPower: 20W
nOutput Voltage: DC 12V, 1 A
nSpeed: 0-30,000 RPM
nThe actual max speed will be less than 30,000RPM.
nDiameter of bits should be 2.2 -2.4mm otherwise it cannot be seized.
Issues Cause Remedy
TROUBLESHOOTING
Motor fails to run
Motor stop suddenly in use
[safety protection system functioned]
Motor fails to run when foot
pedal is used
Loose connection motor plug
with jack in control unit
Defect in motor cord
Trouble in motor
Correctly plug the motor cord
Replace motor cord
Check motor and repair if the motor is troubled
Overloaded or chuck is opened
during operation Check the chuck and close the chuck if opened
H/F selector is at “H”
Foot pedal fails to function
Defect in foot pedal cord
Loose connection foot pedal
plug with jack in control unit
Switch off
Set it at “F”
Check and replace foot pedal
Check and replace foot pedal
Check foot pedal plug and connection
Check power switch “ON”