Dock Doctors Paddle Products Beach Dolly User manual

Beach Dolly with sling & keel pad
Assembly Instructions
PART NAME QTY
A. AXLE......................................... 1
with tongue bracket and sling supports attached
B. SLING SUPPORT BAR ................. 2
C. TONGUE.................................... 1
D. TONGUE TBRACKET.................. 1
E. HANDLEBAR.............................. 1
with bow pad and handle attached
F. HANDLE.................................... 1
G. WHEEL ..................................... 2
H. SLING BRACKET......................... 2
with sling attached
I. SLING........................................ 1
J. KEEL PAD .................................. 1
K. BOW PAD .................................. 1
L. END CAP ................................... 3
Toll Free: 1-800-870-6756 | [e-mail] | www.thedockdoctors.com 1
© 2016 The Dock Doctors - V0416
A
B
D
C
E
F
G
I
J
K
H
A
B
C
E
GIJK
H
D
L
L
L
F

Beach Dolly with sling & keel pad
Step 1: Attach sling support bars to axle:
Lay the axle on its side as shown below.
Take the (2) sling support bars and slide two brass nuts into the channel.
Slide the sling support bar into the sleeve on the axle, then guide the brass nuts into place using the allen wrench. Line the
brass nuts up with the holes in the sleeve.
Insert (2) allen bolts (with washers attached) into the holes, aligning them with the brass nuts underneath.
Hand tighten, then tighten
with the provided allen
wrench.
Repeat with the other sling
support bar.
Step 1
Parts Needed Quantity
Axle 1
Sling Support Bars 2
Brass Nuts 4
Washers 4
Allen Bolts 4
Toll Free: 1-800-870-6756 | [e-mail] | www.thedockdoctors.com 2
© 2016 The Dock Doctors - V0416
sling support bar will slide into sleeve here
axle

Beach Dolly with sling & keel pad
Step 2: Attach tongue to axle t-bracket:
Slide two brass nuts into the channel on the tongue, then turn the tongue over, and
slide two more brass nuts into the channel on the back side of the tongue.
Slide the tongue into the t-bracket on the axle. Guide the brass nuts into place using the allen wrench.
Line the brass nuts up with the holes in the sleeve.
Insert (2) allen bolts (with washers attached) into the
holes, aligning them with the brass nuts underneath.
Hand tighten, then tighten with the provided allen
wrench.
Flip the axle/tongue assembly over and repeat for the
other (2) brass nuts on the other side.
Step 2
Parts Needed Quantity
Tongue 1
Axle from Step 1 1
Brass Nuts 4
Washers 4
Allen Bolts 4
Toll Free: 1-800-870-6756 | [e-mail] | www.thedockdoctors.com 3
© 2016 The Dock Doctors - V0416

Beach Dolly with sling & keel pad
Step 3: Attach wheels to axle:
Slide (1) wheel washer onto the end of the axle.
Then, slide (1) wheel onto the end of the axle.
Insert one locking pin into the hole on the end of the axle to secure the wheel in place.
Step 3
Parts Needed Quantity
Wheel 2
Axle from Step 1 1
Wheel Washer 2
Locking Pin 2
Toll Free: 1-800-870-6756 | [e-mail] | www.thedockdoctors.com 4
© 2016 The Dock Doctors - V0416

Beach Dolly with sling & keel pad
Step 4: Attach Keel Pad:
Slide the keel pad onto the tongue. Slide it about 12” from the end of the tongue.
Tighten the allen bolt on the end of the keel pad bracket.
Step 5: Attach Handlebar:
Slide the bracket on the handlebar onto the tongue. Tighten the allen bolts on the
side of the bracket on the handlebar.
Step 4
Parts Needed Quantity
Keel Pad with bracket 1
tighten allen bolts to secure handlebar to tongue
Step 5
Parts Needed Quantity
Handlebar 1
with handle attached
Toll Free: 1-800-870-6756 | [e-mail] | www.thedockdoctors.com 5
© 2016 The Dock Doctors - V0416

Beach Dolly with sling & keel pad
Step 6: Attach End Cap on Tongue:
Attach (1) of the plastic end caps onto the end of the tongue. (Do not use the other (2)
end caps yet, you will install them in Step 9).
Step 7: Attach Sling:
Unroll the sling as shown below, making sure the webbing strap is not twisted.
NOTE: The allen bolts on the sling bracket should face the
front of the dolly when installed on the sling support bars.
Step 6
Parts Needed Quantity
End Cap 1
Step 7
Parts Needed Quantity
Sling brackets 2
with sling attached
allen bolts on sling bracket need to face
toward the front of the dolly
➞
allen bolt on sling bracket
Toll Free: 1-800-870-6756 | [e-mail] | www.thedockdoctors.com 6
© 2016 The Dock Doctors - V0416

Beach Dolly with sling & keel pad
Step 8: Attach Sling (continued):
Slide one bracket on the end of the sling onto the sling support bar, making sure the allen bolt on the sling bracket
faces the front of the dolly. Slide the bracket on the other end of the sling onto the other sling support bar.
Step 9: Install End Caps:
Install the remaining (2) end caps onto the end of the sling support bars.
Step 10: Tighten Sling Brackets:
After installing the end caps, raise the sling bracket up to the height of
the end cap, then tighten the allen bolt on the side of the sling brackets,
using the allen wrench.
allen bolts on sling bracket need to face toward the front of the dolly
Toll Free: 1-800-870-6756 | [e-mail] | www.thedockdoctors.com 7
© 2016 The Dock Doctors - V0416