Dogtrace d-control 640 User manual

elektronický vibrační výcvikový obojek
Electronic vibration training collar
Elektronisches Vibrations-Trainingshalsband
Collier électronique de dressage par vibrations
Elektronische trainingshalsband
d-control
640,1040,1640
640,1040
1640

16
DECLARATION OF CONFORMITY
We:
VNT electronics s.r.o.
Dvorská 605
563 01 Lanškroun
IČO: 64793826
declare under own responsibility that the product:
Electronic vibration training collar
Dogtrace d-control 640, 1040 and 1640
is in compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EC meets requirements of General Licence of The Czech
Telecommunication Oce according to general
licence no. VO-R/10/05.2014-3 and corresponds to the following standards:
ETSI EN 301 489-1 V1.9.2
ETSI EN 301 489-3 V1.6.1
ETSI EN 300 220-2 V.2.4.1
ETSI EN 60950-1 ed.2:2006/A1:2010/A11:2009/A12:2011/A2:2014/Cor.1:2012
EN 62479:2010
The product is safe on condition of commonly used in conformity with instruction
manual. The Declaration of Conformity is based on following dates:
Measuring report no.: 6440-7600/2008 issued by certicated laboratory no.1103
VTÚPV Vyškov
Measuring report no.: 6440-697/2008 issued by certicatved laboratory no.1103
VTÚPV Vyškov
This declaration of Conformity is created in exclusive responsibility of producer.
In Lanškroun 1. 1. 2018
Ing. Jan Horák
executive director
Tel.: [phone]
[e-mail]
www.dogtrace.com
Hereby, VNT electronics s.r.o., declares that this d-control 640, 1040 and 1640
is in compliance with the essential requirements and other relevant provisions
of Directive 2014/53/EC.
Thank you for purchasing the d-control Dogtrace brand from
VNT electronics s.r.o.
Before using your product, please read the instructions in this user guide
carefully and keep it for future reference.

17
1 CONTENTS
dog training
basic commands dogtraceofficial
2 Important notice ...................................................... 18
3 ECMA ................................................................. 18
4 Introduction ........................................................... 19
4.1 Package contents ....................................................... 19
4.2 Optional accessories .................................................... 19
5 Product description .................................................... 20
6 Transmitter preparation ................................................ 20
6.1 Battery insertion and replacement in the transmitter . . . . . . . . . . . . . . . . . . . . . 20
6.2 Switching the transmitter ON/OFF ...................................... 21
7 Receiver preparation ................................................... 21
7.1 Battery insertion and replacement in the receiver ........................ 21
7.2 Checking the battery status ............................................. 21
7.3 Switching the receiver ON/OFF .......................................... 22
8 Programming (coding) the transmitter with the receiver ................. 22
8.1 Pairing of the button 1with the rst receiver ............................ 23
8.2 Pairing of the button 2with the second receiver ......................... 23
8.3 Reprogramming of your receiver ......................................... 23
8.4 Fitting the collar ........................................................ 23
9 The basics of training collar usage ...................................... 24
9.1 Transmitter – button functions .......................................... 25
10 For the best results .................................................... 27
10.1 Maximum transmitter range ........................................... 27
10.2 Using training collar in winter .......................................... 27
11 Troubleshooting ....................................................... 27
12 Maintenance .......................................................... 28
13 Technical data ......................................................... 28
14 Warranty terms and conditions ......................................... 29
15 Certicate of warranty ................................................. 72

18
The electronic training collars d-control are intended only to train animals. They
are not intended to harm, injure or to cause fear.
Do not use the electronic training collars for dogs with health problems (e.g.
heart disease, epilepsy, etc.) or for dogs with behavioral disorders (aggressive
dogs etc).
The collar should never be worn for more than 12hours aday. Long-term eect
of contact points on the dog’sskin can cause skin irritation. If arash or sore skin
is found, do not use the collar until it has healed.
Never connect aleash to the electronic collar; this could cause excessive pressure
on the contact points or mechanical damage of the receiver.
In case of any problems or for further advice do not hesitate to contact
aprofessional trainer.
Do not place the transmitter close to objects which are sensitive to magnetic
eld, this could cause apermanent damage.
Receiver and transmitter batteries need to be replaced every two years, even if
the kit has not been used. Never leave at batteries inside of the device - it could
damage your device.
The person with a personal instrument to support heart activity (pacemaker,
debrillator) must respect the relevant precautionary measures. The d-control
professional emits acertain stationary magnetic eld.
2 IMPORTANT NOTICE
VNT electronics s.r.o., professional producer of the dog training
equipment under the brand name Dogtrace, is aproud and active
member of the Electronic Collar Manufacturers Association.
ECMA was founded in Brussels in 2004as a result of increasing
awareness from dierent manufacturers concerning the necessity of regulating
their industry. The main target of the association is to develop and produce reliable
training systems of high quality, which are safe for the animals and improve the
communication between pets and their owners. All ECMA member´sproducts meet
the latest technical requirements which ensure minimum production standards and
safety features and enable training while protecting animal welfare.
For more information please visit www.ecma.eu.com.
3 ECMA

19
The d-control electronic vibration training collar consists of a transmitter and
areceiver. It is areliable, eective and safe means of training your dog. The d-control
training collar allows you to make corrections of unwanted behaviour at the right
time, taking into account the current situation and your dog'stemperament. This
helps to make training as eective as possible. However, eliminating undesirable
behaviour is only asmall part of what you can achieve with the electronic training
collar in training. Electronic vibrating training collars d-control 640, 1040 and
1640 have vibration, light and acoustic signal functions. The vibration function has
been designed as an alternative communication method for training dogs
hypersensitive to stimulus or for training dogs with hearing impairments. The light
function makes it easy to locate your dog in the dark. These models are designed
for training one or two dogs.
Features of d-control 640, 1040, 1640
range up to 600, 1000, 1600m (depending on the model)
waterproof receiver
audible beep tone
5modes of vibration
8modes of light
expands to train two dogs
backlit LCD
4.1 Package contents
collar (receiver) including astrap
1pcs CR2 3V lithium battery
2pcs alcaline battery AA 1,5V
remote controller (transmitter) with afastener
string for hanging the transmitter around neck
user’sguide and warranty certicate
case
4.2 Optional accessories
Dummy receiver (with the strap)
Spare batteries
Spare screws
Spare rubber seal for the transmitter and the receiver
Woven and plastic collars – various colours
4 INTRODUCTION

20
5 PRODUCT DESCRIPTION
6 TRANSMITTER PREPARATION
6.1 Battery insertion and replacement in the transmitter
1. Remove the cover of the battery compartement and insert 2AA alcaline batteries.
Mind the correct polarity marked in the battery compartement.
2. Replace the cover and tighten the screw.
The battery power indicator on LCD shows the battery status:
– Fully charged battery
1 2
3
4
TRANSMITTER RECEIVER
LCD DISPLAY
2
3
4
7
6
5
1
6
7
12
3
TRANSMITTER – 1 – Backlit LCD display, 2 – Vibration button, 3 – Light button,
4 – Tone signal button, 5 – ON/OFF Switch, 6 – Vibration mode selection button,
7 – Dog selection button (dog 1, dog 2)
RECEIVER – 1 – Indicator area where the ON/OFF magnetic switch is located,
2– ON/OFF LED Indicator, 3 – Contact points
DISPLAY – 1 – Indicator of the radio transmission, 2 – Battery power indicator,
3 – Stimulation intensity level indicator, 4 – Dog selection indicator (dog 1,
dog2)

21
– Medium charged battery
– Flat battery
If the battery is at, insert new AA alkaline batteries into the battery compartment.
Make sure that the receiver works correctly.
TIP: The battery can be taken out easily by small screwdriver, which is placed
carefully under the the battery edge.
6.2 Switching the transmitter ON/OFF
Switching ON: Press down for 1second the button on the transmitter. The LCD
display indicates that the unit is active.
Switching OFF: Again, press down for 1second the button on the transmitter.
7.1 Battery insertion and replacement in the receiver
1. Screw out 4screws from the battery cover using across-head screwdriver and
remove the lid.
2. Insert the lithium CR2 3V battery into the battery compartment with acorrect
polarity (according to the polarity indicated with the “+” symbol in the battery
compartment – see the picture). A wrong
polarity may damage the unit.
When you insert the battery for the rst time, or if
the battery is removed longer than afew tens of
minutes, you will hear an audible beep tone
indicating the correct installation of the battery.
Note: When you replace the battery quickly, you
may not hear the audible beep tone of the collar.
3. Make sure that the rubber seal is clean and
correctly seated in its groove. Clean any dirt
from the seal.
4. Put the battery cover of the receiver back and
screw in the 4screws adequately.
7.2 Checking the battery status
The status of the battery is indicated by LED indicators on the side of the receiver.
(see chapter: 5Product description – Receiver)
The batterry is fully charged – when switched on, green LED is flashing
The battery is low –when switched on, red LED is ashing
7 RECEIVER PREPARATION
Battery polarity mark

22
When the battery is low or at, insert anew CR2 3V lithium battery into the receiver.
7.3 Switching the receiver ON/OFF
Amagnet located at the lower part of the transmitter is
used to activate or deactivate the magnetic switch
located in the receiver.
Switching ON:
Approach the low area of the transmitter where the
magnet is located until coming close to the indicator
located on the receiver (see the picture), hold for
1 second, the receiver LED indicator will ash in green
indicating the receiver is ON.
Switching OFF:
Approach the low area of the transmitter where the
magnet is located until coming close to the indicator
located on the receiver, hold for 1 second, the receiver
LED indicator will ash from green to red indicating the receiver is OFF.
Switching ON/OFF the
transmitter/Programming
the transmitter with the
receiver
IMPORTANT: When switching on or o, simply hold the transmitter against the
receiver target for approximately 1second. If you hold for more than 5seconds,
the receiver will go into transmitter-receiver pairing mode. This mode is
indicated by the green and red indicator lights ashing simultaneously. If this
occurs, follow the steps in the section 8Programming (coding) the transmitter
with the receiver.
To extend the battery life it is necessary to switch o both receiver and transmitter
after the training is nished. If the battery will not be in use for amonth or longer,
it is recommended that it is removed from the receiver.
Each transmitter has its own RF operational code. The pairing needs to be done to
make the receiver and transmitter operate together. When you receive anew set
the pairing is done by manufacturer. The pairing is done, when you need to use
dierent transmitter or receiver (for example when bought anew one).
The transmitter is made for training of two dogs, so you can pair it with two
receivers. Use the button /to choose the right dog.
8 PROGRAMMING CODING THE TRANSMITTER
WITH THE RECEIVER
IMPORTANT: Before the programming make sure no other person is using his
d-control or other products from the Dogtrace range close by: your receiver
could accidentally record the code of his transmitter.

23
8.1 Pairing of the button with the rst receiver
1. Turn ON your transmitter.
2. The receiver has to be turned OFF.
3. Press the button for the rst receiver choice.
4. Move the lower part of the transmitter to the target on your receiver (see the pic.
on page 22) and hold in position so the green LED is steadily lit. After
approximately 5 seconds it will switch to the pairing / programming mode,
indicated by ashing of the red and green LED at the same time (4x).
5. Then take your transmitter away from the receiver and press down the audible
beep tone button on your transmitter. If you hear the beep tone the pairing
has been successful.
8.2 Pairing of the button with the second receiver
Press the button for the second receiver choice and follow the steps as for the
rst receiver above (this can be followed when you use d-control 640, 1040, 1640
with anew purchased receiver).
8.3 Reprogramming of your receiver
The receiver can be programmed repeatedly without restraint using the same
transmitter or another (see the section 8 Programming (coding) the transmitter
with the receiver).
TIP: It is possible to program an unlimited number of receivers to a one
transmitter.
Example: Button is paired with 3receivers, they can be programmed one by
one or we can set all 3in pairing regime and then press button for audible beep
tone. All these receivers will perform the same action at the same time when
pressing function button. This can be used for two collars on the neck of one dog,
or for the training of higher number of dogs, where we give the same commands to
all of them at the same time.
8.4 Fitting the collar
The strap with the receiver (receiver collar) must be tightened enough so that the
contact points are in contact with the skin of the dog. We recommend you to t the
collar on the standing dog. When you can t two ngers between the collar and your
dog‘s neck, the collar with the receiver are tightened enough. If a dog has long or
thick hair, it is suitable to trim the hair in the area of the contact points or to switch to
the longer contact points to ensure aconsistent contact.

24
The trainer’s elementary knowledge of the dog training is the prerequisite for
using the training collar.
If you don´t have this knowledge, we recommend you to contact a training
center, a cynology club, or a school for dogs where you will learn the basic
communication with your dog.
You can start using the collar for the 6months old dog, which have undergone
the basic training and is familiar with basic obedience commands including „sit“,
„down“, „stay“ or at least „stop it“, „leave it“.
Require these commands along with the audible beep tone, so your dog will
create aconnection between them.
After a command that is successfully executed, you should always reward or
encourage your dog, so the dog will be happy to fulll your commands and
adesire to fulll your commands will grow.
You must not consider the executed command as the absolute obviousness and
punish disobedience - your dog would soon lose an interest.
If you are not sure that your dog will obey you after recall, start training e.g. on
atracking rope.
Your dog will have to get used to the collar; let the dog wear the collar for afew
days, but do not use it so that your pet does not discover the connection with its
attachment and eects.
Armative and ecient training requires some time: don‘t hurry!
Select awell-known environment your dog is used to.
Choose the right moment to press the button; exactly at the moment when your
dog does something what is not allowed.
In case of any problems and for further advice, please do not hesitate to contact
aprofessional trainer.
9 THE BASICS OF TRAINING COLLAR USAGE
WARNING: If the collar is too loose, the receiver is likely to move and the
repeating friction can irritate the skin of your dog. Furthermore, in this case is
not ensured a reliable contact of contact points with the skin and a proper
function of the training collar. We do not recommend to leave the collar
positioned at the same place for more than several hours, because it could
irritate the skin. If it is necessary to wear the collar for long periods, change
regularly the position on the neck of your dog. Acollar with areceiver that is
overly tight, can cause pressure sores on the skin in the contact area of the
contact points. If this happens, do not use the training collar until all traces of
irritation are gone.

25
9.1 Transmitter – button functions
Audible beep tone
When pressing the button for beep tone, the receiver on dog‘scollar begins to emit
an audible beep tone (an acoustic signal). This command can precede avibration
impuls. It is also a very eective warning tool. You can use the acoustic signal
instead of the command: Come!/Heel! In this case it replaces a whistle, the dog
always perceives its sound in the same intensity. It‘svery important always to use
the beep sounds in the same way in order not to confuse your dog. While
transmitting the audible beep tone, the green LED indicator of the receiver is
emitting alight.
Vibration
The vibration serves mainly to draw attention of sensitive dogs or training dogs
with impaired hearing. Provides adiscreet recall of the dog, which is with deaf dogs
virtually impossible. It provides the ability to distract dog from undesirable activities
with moment of surprise. Each mode can mean dierent commands, depending on
your training. It can also substitute teaching method using the„clicker“ and treats.
Vibration mode selection
Mode Function
0short vibration
1vibrates as long as you keep the button pressed
2series of interrupted vibrations
3
vibrates interruptedly as long as you keep the button
pressed
4vibrates permanently and releases asound signal
Mode setting is done by using buttons / . Choosen mode is displayed on
LCD, transmission of the vibration is made by pressing the button .
Transmission symbol appears on the remote controller LCD and ared LED on the
receiver is lit permanently.
Light
For an easy localization of your dog in the dark, this function provides 8dierent
modes of LED light. The LED - diodes are placed in the transparent receiver housing
of the collar.

26
Light mode selection
Mode Press of the button Function
0 short/permanent 1× single ash
1 short/permanent ashing as long as the button is pressed
2 short 10× ashes
2 permanent shines as long as button pressed and follows
10×ashes
repetitive press stops the function ahead of time
3 short 1× ash every 0,5seconds
3 permanent shines as long as button pressed and follows 1×ash
every 0,5seconds
4same function as mode 0 with a dierent ashing
frequency
5same function as mode 1 with a dierent ashing
frequency
6same function as mode 2 with a dierent ashing
frequency
7same function as mode 3 with a dierent ashing
frequency
NOTICE: By modes 3 and 6 do not forget to switch o blinking by pressing
button. Modes 4–7can be used for diering dogs in darkness.
Setting the modes: Press adog selection button or (depending on which
button is paired with the required receiver) until symbol 1or 2starts ashing on the
LCD. Set the required mode number (0–7) using the buttons with the arrows
/Conrm the selection by pressing button or again. The
transmitter allows you to set adierent interval of ashing when using two collars
at the same time so you can easily spot your dogs according to the ashing interval
(example: dog 1–mode 1and dog 2–mode 6).
Control buttons
The buttons are used for quick setting of vibration and light modes which are
displayed on the LCD in numbers 0–4 (vibration modes) and 0–7 (light modes).
Control buttons
The buttons are used for dog selection. Adierent impulse level can be set for each
dog. It remains saved even after selection switching to the other dog.

27
10.2 Using training collar in winter
When using d-control in winter, please keep in mind:
Battery properties change – temperatures below 0 °C slow down chemical
reactions in batteries. To ensure aperformance, it is recommended to insert anew
battery into the receiver for the winter time.
maximum range regular range minimum range
10.1 Maximum transmitter range
The training collar d-control 640, 1040, 1640 can be used up to 600–1600 m working
range. The maximum range depends on many factors – weather, terrain, vegetation
and so on.
To ensure maximum working range of the device:
Do not cover the transmitter antenna
When transmitting commands, hold the transmitter in avertical position, away
from the body and above your head
Check the battery in the transmitter and in the receiver, replace it if necessary.
1. Read again this user guide and make sure the problem is not caused by aat
battery or incorrect use.
2. Make sure the batteries are inserted with the correct polarity.
3. If the transmitter does not communicate with the receiver, try to program
communication – see chapter: 8Programming (coding) the transmitter with the
receiver.
4. If the problem still persists, contact the dealer.
10 FOR THE BEST RESULTS
11 TROUBLESHOOTING

28
Transmitter
Range ...................................... from 600 to 1600 meters in afree area
depending on atransmitter model
Power supply .......................................2pcs alkaline battery AA 1,5V
Battery life .........................................6–12months, based on usage
Frequency ................................................ 869,525MHz (500mW)
Antenna .............................................................. integrated
Tightness ........................................................ not waterproof
Operating temperature .......................................... –10°C to +50°C
Weight ............................................88–95 g (without the batteries)
Dimensions .............................. 119 x 53 x 28mm (without the antenna)
Receiver
Power supply .............................................. CR2 3Vlithium battery
Battery life ....................................... 6months, depending on usage
Antenna .............................................................. integrated
Tightness ............................................................ waterproof
Adjustable belt length ................................ approximately 15 to 72cm
Operating temperature .......................................... –10°C to +50°C
Weight ................................................. 55g (without the battery)
Dimensions ..................................................... 64 x 43 x 34mm
13 TECHNICAL DATA
It is important to keep the device clean. Never use volatile substances eg.: thinner,
gasoline or other cleaners. To clean your Dogtrace d-control use asoft, damp cloth
and, if necessary, neutral detergent.
The receiver (collar) is waterproof only on condition of the good state of the
seal. We recommend you to replace the rubber seal, which is placed under the
cover of the battery compartment of the receiver, once ayear. Clean the rubber
seal and make sure that the rubber seal is correctly seated in its groove every time
you change the batteries; tighten the screws using adequate power. If the device is
not used for alonger time, take out the batteries from the battery compartment.
12 MAINTENANCE

29
VNT electronics s.r.o. provides a2year warranty on the Dogtrace products with respect to
defects in material and workmanship under normal use and service from the date of the
original purchase. The limited warranty does not cover the following:
batteries
straps
direct or indirect risks during transportation of the product to the retailer
mechanical damage of the product caused by user‘snegligence or an accident (eg.
biting, breaking, impacts, excessive pulling of d-ring etc.).
1. The warranty period commences on the date of purchase. The sales receipt or your
purchase invoice showing the date of purchase of the product, showing the serial
number and date of purchase of the product, is the proof of the purchase date.
2. The warranty does not cover damage resulting from:
a) improper installation or breach of instructions from the manufacturer‘suser guide
b) improper use of the product
c) improper storage or maintenance of the product
d) modication by a non authorized person, or a repair made without
manufacturer‘sknowledge
e) natural disaster (wind, earthquake, lightning storm, etc.)
f) alternation of the goods made by the consumer if such an alternation resulted in
adamage of the product
g) due to aconsumer’smechanical damage
h) other customer‘sprocess, which would be in acontrary to the Warranty terms and
conditions and the User guide
3. The warranty can not be claimed if the goods is not completely paid, or when purchased
on asale
4. The claimant is obliged to prove the defect and to enable the manufacturer to check the
legitimacy of the product faults and assess the extent of the product faults. Otherwise is
loosing the right arising from the manufacturer’sresponsibility for product defects.
5. Consumer demands arising from the producer‘sliability for defects are regulated in the
general legislation.
6. It is required that all items being sent for arepair must be properly cleaned. Items
deemed to be insuciently cleaned will be returned unrepaired to the customer. Please
do not include the strap or any other accessories if it is not asubject of the warranty.
7. When sending the device to the service with a transport company, pack the goods
adequately to protect it against a damage; it is recommended to keep the original
packaging for this purpose. The producer is not responsible for aloss of goods during
transport.
14 WARRANTY TERMS AND CONDITIONS
The information contained in this manual may be subject to change due to developments without
further notice.
Copying of this user guide is strictly prohibited without the prior written consent of VNT electronics
s.r.o.