Doka Shifting wheel KS User manual

© by Doka GmbH, A-3300 Amstetten
999237002 05/2016
en-GB
-
The Formwork Experts.
Shifting wheel KS
Art. n°: 580358000 | 2001 models onward
Original Operating Instructions
Please retain for future reference
© by Doka GmbH, A-3300 Amstetten

2999237002 - 05/2016
Original Operating Instructions Shifting wheel KS
Basic drawings of product
a ... 206 mm
b ... 133 mm
c ... 339 mm
d ... 720 mm
e ... 110 mm
f ... ø160 mm
Data on rating plate
Designation: Shifting wheel KS
Art. n°: 580358000
Dead weight: 15.8 kg (34.8 lbs)
Max. load-bearing capacity: 300 kg (660 lbs)
Year of manufacture: see rating plate
Intended use
The Shifting wheel KS may only be used for horizontal
repositioning (i.e. "wheeling") of Doka column form-
works KS of up to 3.60 m in height. 4 Shifting wheels
KS are needed for repositioning one Column formwork
KS.
Maintenance & inspection
▪Repairs may only be carried out by the manufacturer!
▪Doka accepts no liability for products that have been
altered!
Before every use
➤Check for any signs of damage or visible deforma-
tion.
At regular intervals
▪Inspection of lifting accessories must be performed
at regular intervals by an expert in conformity with
national statutory provisions.
Unless otherwise stipulated, such inspection must
be carried out at least once a year.
Storage
▪Store lifting accessories in a dry and well ventilated
place, protected from the weather and from all corro-
sive substances.
Mounting the Shifting wheels KS
➤Dismount the Connecting pin 10cm .
➤Slot the top of the Shifting wheel KS unit into the
cross-profile and frame tube, and pivot the whole unit
into position.
➤Use the Connecting pin 10cm to fix the Shifting
wheel KS in the bottom location fixture, and secure it
with a spring cotter.
Max. load-bearing capacity: 300 kg / shifting wheel
☞Important note:
▪It is forbidden to use the product for anything
but its designated purpose!
▪It is forbidden to lift other manufacturers'
formwork with it.
e
c
b
a
d
f
Lifting accessories that do not meet the follow-
ing criteria must be withdrawn from use imme-
diately:
▪Crack-free and notch-free welds.
▪No deformation.
▪Rating plate must be in place and clearly
legible
9237-202-01
9237-203-01

Original Operating Instructions Shifting wheel KS
3999237002 - 05/2016
Horizontal repositioning
Wheeling
The Shifting wheel KS makes it possible for Column
formworks KS Xlife of up to 3.60 m in height to be hori-
zontally travelled.
It can be clamped to 2.70 m and 3.30 m high panels.
4 Shifting wheels KS are needed for repositioning 1
Column formwork KS Xlife.
➤Using the spindles, raise the Column formwork KS
Xlife around 2 cm off the ground.
➤When wheeling the formwork, always have 2 people
pushing (1 on either side).
☞The following points MUST be observed –
otherwise you risk the formwork tipping
over
▪Do not attempt to wheel any Column form-
work KS higher than 3.60 m.
▪Only wheel the column formwork when it is
CLOSED – fix it in the closed position with a
Locking hook KS.
▪The floor must be stable, firm and sufficiently
smooth (e.g. concrete).
▪Max. speed 4 km/h (walking pace)
▪Either bridge any openings in the floor with
sufficiently strong planking/boards secured
so that they cannot slip away to either side,
or close off openings with sufficiently strong
side railings!
▪Keep the travel route clean and free of any
obstacles.
▪It is forbidden to wheel the column formwork
when the wind-speed is higher than 45 km/h
(over 0.1 kN/m2impact pressure to DIN
4420).
▪It is forbidden to use any mechanical assis-
tance during the wheeling operation!
▪"Passenger transportation" is forbidden.
▪In the "parked" position, always lower the
Column formwork KS using the spindles.
9746-321-01
EC Declaration of Conformity
pursuant to EC Directive 2006/42/EC.
The manufacturer declares that by reason of its conception and
design, the following product
Shifting wheel KS, art. n° 580358000
conforms – in the version marketed by ourselves – to the pertinent
fundamental health and safety stipulations of the relevant EC Direc-
tives.
The following harmonised standards were applied:
▪EN ISO 12100:2010
▪EN 349:1993+A1:2008
Person authorised to compile technical documentation
(pursuant to European Directive on Machinery Annex II):
Ing. Johann Peneder
Josef Umdasch Platz 1
A-3300 Amstetten
Amstetten, 3 May 2016
Doka GmbH
Josef Umdasch Platz 1
A-3300 Amstetten
Ludwig Pekarek
Executive Manager
Johann Peneder
Authorised Officer, Head of R&D
9746-336-02