DoorKing 1602-162 User manual

1
1602-149-H-10-22
Lockwasher 3/8”
Washer 3/8”
Hub
Horizontal Arm Direction
Counterweight
Mounting
Plate Holes
Hex Bolt 1/2” x 1”-3/4” Tap
Locking Plate Washer
Phillips Screw 10-32 x 1/2”
Hub
Vertical Arm Direction
Mount hubs on
operator FIRST.
Test hubs UP and
DOWN positions
BEFORE installing
counterweight
mounting plates,
then assemble arms
and cables.
Clip around counterweights
before screwing cover on.
Counterweight
Mounting Plate
See
next
page
Hex Nut 3/8”
Hex Bolt 3/8” x 1”
Counterweight Mounting Plate
Hardware x 4
Counterweight
Mounting Plate
Hardware x 4
Washer 3/8”
Support arms during assembly until all cables
have been installed and adjusted for level.
DoorKing Part Numbers:
1602-162
20 ft Arm
1602-164
24 ft Arm
1602-166
27 ft Arm
Washer 3/8”
Nylon Washer
Hex Head Screw
Cotter Pin
UHMW Shear Pin
3/8” Washer
& Cotter Pin
3-PIECE ROUND ARM KITS
These kits are designed ONLY for the 1602 model barrier gate operator.
Copyright 2023 DoorKing®, Inc. All rights reserved.
120 S. Glasgow Avenue
Inglewood, California 90301 U.S.A.
Test hub UP and DOWN position
before installing arms.

2
1602-149-H-10-22
Wishbone Steel Cables Note:
These 2 steel cables are used
on ALL arm assemblies.
The End of Arm Assembly steel cable is ONLY used on the 27 ft arm.
The 20 ft and 24 ft arms DO NOT use this steel cable.
Adjust ALL cables
with turnbuckles to
make the arms level.
Wishbone Hardware Assembly
End of Arm
Washer 3/8”
Hex Bolt 3/8” x 4” and Washer 3/8”
Washer 3/8”
Lockwasher 3/8”
Hex Nut 3/8”
Turnbuckle Eye
Bolt and Nut
Turnbuckle Thimble
Eye
Thimble
Eye 2 Cable
Clamps
2 Cable
Clamps
UHMW Shear Pin
3/8” Washer & Cotter Pin
Washer 3/8”
Washer 3/8”
Eye Bolt 3/8” x 4”
Lockwasher 3/8”
Hex Nut 3/8”
Cotter Pin
Stainless Steel
Cable on 27 ft
models ONLY
Wishbone Stainless Steel Cables
14 ft Arm
14 ft Arm
Washer 3/8”
Eye Bolt 3/8” x 4”
Washer 3/8”
Thimble
Eye
2 Cable
Clamps Stainless Steel Cable
Stainless Steel Cable
Lockwasher 3/8”
H
ex Nut 3/8”
Plastic
End Cap
Hex Nut 3/8”
Washer 3/8”
Hex Bolt 3/8” x 1”
Hex Bolts 3/8” x 1”
Turnbuckle
2 Cable
Clamps Thimble
Eye
Lockwasher 3/8”
Hex Nuts 3/8”
Lockwashers 3/8”
Support arms during assembly until all cables
have been installed and adjusted for level.
Wrap cable around Thimble Eye
and secure with
2 Cable Clamps
at each end of
ALL cables.
Stainless Steel Cable
Cable Clamp 1
Thimble
Eye
Cable Clamp 2