Dorel DA1010-CU User manual

INSTRUCTION MANUAL
TWIN / TWIN BUNK BED
Model No:
DA1010-CU (WHITE)
DA1010-1C / DA1010-2C (WHITE)
DA1010G-CU (GRAY)
DA1010G-1C / DA1010G-2C (GRAY)
Lot number:
UPC CODE:
0-65857-17960-6 (WHITE)
0-65857-17958-3 / 0-65857-17959-0 (WHITE)
0-65857-17963-7 (GRAY)
0-65857-17961-3 / 0-65857-17962-0 (GRAY)
NOTE:
(TAKEN FROM CARTON)
______________________________
Date of purchase:
______ / ______ / ______
THIS INSTRUCTION BOOKLET
CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND
KEEP FOR FUTURE REFERENCE.
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, contact our customer
service department. We will replace the part
FREE of charge.
Tel #: [phone]
E-Mail: [email protected]om
Fax #: [phone]
NEED HELP!
CALL US FOR ASSISTANCE
1-800-295-1980
DO NOT RETURN PRODUCT TO STORE
E-MAIL:[e-mail]

*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE
BED.
DO NOT USE SUBSTITUTE PARTS. CONTACT CUSTOMER SERVICE FOR
REPLACEMENT PARTS.
USE OF A NIGHT LIGHT MAY PROVIDE ADDED SAFETY PRECAUTION FOR A CHILD
USING THE UPPER BUNK.
DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK.
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK
BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS THE FULL
LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT
ENTRAPMENT BETWEEN THE BED AND WALL (APPLICABLE FOR BUNK BEDS WITH
FULL LENGTH GUARDRAILS ON ONE SIDE).
ALWAYS USE THE LADDER FOR ENTERING AND LEAVING THE UPPER BUNK.
KEEP THESE INSTRUCTIONS FOR FUTURE USE.
THE USE OF WATER OR SLEEP FLOTATION MATTRESSES IS PROHIBITED.
PROHIBIT MORE THAN ONE PERSON ON UPPER BUNK.
PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL, LADDER AND OTHER
COMPONENTS ARE IN THEIR PROPER POSITION, FREE FROM DAMAGE, AND THAT ALL
CONNECTORS ARE TIGHT.
USE ONLY COIL SPRING MATTRESSES ON BOTH THE UPPER AND LOWER BUNKS.
FAILURE TO DO SO CAN RESULT IN INJURY.
USE ONLY MATTRESSES WHICH ARE 74"-75" LONG AND 37 1/2" - 38 1/2" WIDE ON
UPPER AND ON LOWER BUNKS. ENSURE THICKNESS OF MATTRESS DOES NOT
EXCEED 6". SURFACE OF MATTRESS MUST BE AT LEAST 5" (127MM) BELOW THE
UPPER EDGE OF GUARDRAILS.
STRANGULATION HAZARD - NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE
BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; FOR EXAMPLE, BUT
NOT LIMITED TO HOOKS, BELTS AND JUMP ROPES.
ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR
BOTH, TO HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS.
FOLLOW THE INFORMATION ON THE WARNINGS APPEARING ON THE UPPER BUNK
END STRUCTURE AND ON THE CARTON. DO NOT REMOVE WARNING LABEL FROM
BED.
THE MATTRESS PLATFORM IS DESIGNED TO SUPPORT A MATTRESS WITHOUT THE
NEED FOR A POSTURE BOARD OR BOX SPRING.
E-MAIL: [email protected]
WARNING
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service
representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product
model number, color and a detailed description of the part.
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
Montreal, Quebec
Canada, H1G 3L1

*
*
*
*
*
*
*
*
Check bolts/screws periodically and tighten them if necessary.
Dorel warrants its product to be free from defects in material and workmanship and agrees to
remedy any such defect. This warranty covers 1 year from the date of original purchase. This
warranty is valid only upon presentation of proof of purchase. This is solely limited to the repair
or replacement of defective furniture components and no assembly labor is included. This
warranty does not apply to any product which has been improperly assembled, subjected to
misuse or abuse or which has been altered or repaired in any way. This warranty gives you
specific legal rights and you may also have other rights which vary from State to State
WARNING: Should this product
become damaged, and/or components
are broken or missing, DO NOT USE.
READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH
STEP OF INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS
ARE NOT FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN
RESULT IN INJURY.
MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A
SMOOTH SOFT SURFACE.
ASSEMBLY WILL REQUIRE TWO PEOPLE.
PHILLIPS SCREWDRIVER (NOT INCLUDED) IS REQUIRED.
CAUTION: ADULT ASSEMBLY REQUIRED
MOST BOARD PARTS ARE LABELED OR STAMPED ON THE RAW EDGE.
MAINTENANCE
LIMITED WARRANTY
CARE AND CLEANING
Dust regularly with a soft, dry cloth. We do not recommend the use of chemical cleaners or wax
on our lacquered furniture as it may damage the finish. Keep solvents, alcohol, nail polish and
polish removers away from your hardwood furniture surfaces.
A RUBBER MALLET (NOT INCLUDED) IS RECOMMENDED TO FACILITATE ASSEMBLY.
BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG
TEENAGERS.
NOTES

1 2
3 4
5 6
7 8
910
∅11.8mm x 15mm
WOOD DOWEL
14 PCS
∅10mm x 50mm
∅4mm x 35mm
ALLEN KEY
1 PC
CAP
4 PCS
∅4mm x 30mm
BARREL NUT
16 PCS
∅6.5mm x 100mm
FLAT HEAD WOOD SCREW
6 PCS
FLAT HEAD WOOD SCREW
20 PCS
WOOD DOWEL
4 PCS
∅19mm x 95mm
WOOD JOINT CONNECTOR (4mm HEX HEAD)
6 PCS
HARDWARE LIST
TWIN / TWIN BUNK BED
JOINT CONNECTOR (4mm HEX HEAD)
16 PCS
WOOD JOINT CONNECTOR (4mm HEX HEAD)
14 PCS
∅1/4" x 100mm
∅6.5mm x 48mm

A B C
TWIN / TWIN BUNK BED
LEFT HEADBOARD
2 PCS
RIGHT HEADBOARD
1 PC
FOOTBOARD
2 PCS
PARTS LIST

D E F
G H I
J K L
M N
TWIN / TWIN BUNK BED
PARTS LIST
TOP SIDE RAIL
(WITH 3 HOLES)
1 PC
BOTTOM SIDE RAIL
(WITH 2 HOLES)
1 PC
TOP SIDE RAIL
(WITH 1 HOLES)
1 PC
BOTTOM SIDE RAIL
(WITH NO HOLES)
1 PC
SLAT
2 PCS
LONG GUARDRAIL
2 PCS
SHORT GUARDRAIL
2 PCS
LONG LADDER END
1 PC
GUARDRAIL LEG
2 PCS
SHORT LADDER END
1 PC
LADDER STEP
4 PCS

TWIN / TWIN BUNK BED
Attach footboards (C) to the bottom side rails (E and G) using joint connectors (1) and
barrel nuts (8) as shown.
Use Allen key (9) to tighten all joint connectors.
Note: This is the lower bunk.
STEP 1
I
K
Holes
1
1
9
8
8
8
8
I
K
Holes
1
1
9
8
8
8
8

STEP 2
Insert wood dowels (7) into each end of the long guardrails (I). Attach two long
guardrails (I) and two top side rails (D and F) to the headboards (A and B) as shown.
Fasten top side rails (D and F) with joint connectors (1) and barrel nuts (8). Fasten long
guardrails (I) with wood joint connectors (3) .
Use Allen key (9) to tighten all joint connectors.
This is the upper bunk.
TWIN / TWIN BUNK BED
3
M
3
M
3
M

STEP 3
Attach slats (H) to side rails (D and F) of the upper bunk and (E and G) of the lower bunk
with flat head wood screws (4) using a Phillips head screwdriver (not included).
TWIN / TWIN BUNK BED

STEP 4
Insert wood dowels (7) in the ends of short guardrails (J). Attach short guardrails (J) to left
headboard (A) with wood joint connectors (3). Attach the guardrail leg (N) to the short
guardrails (J) and top side rail (D) with flat head wood screws (5). Attach another guardrail
leg (N) to long guard rails (I) and top side rail (F) with flat head wood screws (5).
Use a Phillps head screwdriver (not included) to install screws (5).
TWIN / TWIN BUNK BED