Dorel WM3797W User manual

BUNK BED
Model No.:
WM3797W
0 29986 59210 1
Lot number:
(TAKEN FROM CARTON)
NOTE:
_______ / _______ / _______
THIS INSTRUCTION BOOKLET
CONTAINS IMPORTANT SAFETY
KEEP FOR FUTURE REFERENCE.
INFORMATION. PLEASE READ AND
Date of purchase:
UPC CODE:
DOREL HOME FURNISHINGS
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, contact our customer service
department. We will replace the part FREE of charge.
Tel # : [phone]
E-Mail: [e-mail]
Fax #: [phone]
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, contact our customer service
department. We will replace the part FREE of charge.
Tel # : [phone]
E-Mail: [e-mail]
Fax #: [phone]

*
*
*
*
*
*
*
*MAXIMUM WEIGHT CAPACITY: 165 LBS (75 KGS) PER LEVEL
*
*
*
*
*
*
*
USE ONLY COIL SPRING MATTRESSES ON BOTH THE UPPER AND LOWER BUNKS.
FAILURE TO DO SO CAN RESULT IN INJURY.
ALWAYS USE THE RECOMMENDED SIZE MATTRESS OR MATTRESS SUPPORT, OR BOTH,
TO HELP PREVENT THE LIKELIHOOD OF ENTRAPMENT OR FALLS.
Montreal, Quebec
Canada, H1G 3L1
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact our customer service
representative first!
CALL 1-800-295-1980
You can also order parts by writing to the address listed below. Please include the product model
number, color and a detailed description of the part.
Customer Service Department No. 413
12345 Albert-Hudon Boulevard, Suite 100
E-MAIL: [email protected]
WARNING
STRANGULATION HAZARD - NEVER ATTACH OR HANG ITEMS TO ANY PART OF THE
BUNK BED THAT ARE NOT DESIGNED FOR USE WITH THE BED; FOR EXAMPLE, BUT NOT
LIMITED TO HOOKS, BELTS AND JUMP ROPES.
FOLLOW THE INFORMATION ON THE WARNINGS APPEARING ON THE UPPER BUNK END
STRUCTURE AND ON THE CARTON. DO NOT REMOVE WARNING LABEL FROM BED.
THE MATTRESS PLATFORM IS DESIGNED TO SUPPORT A MATTRESS WITHOUT THE
NEED FOR A POSTURE BOARD OR BOX SPRING.
USE ONLY MATTRESSES WHICH ARE 74"-75" LONG AND 37 1/2" - 38 1/2" WIDE ON UPPER
AND ON LOWER BUNKS. ENSURE THICKNESS OF MATTRESS DOES NOT EXCEED 6".
SURFACE OF MATTRESS MUST BE AT LEAST 5" (127MM) BELOW THE UPPER EDGE OF
GUARDRAILS.
DO NOT ALLOW CHILDREN UNDER 6 YEARS OF AGE TO USE THE UPPER BUNK.
ALWAYS USE THE LADDER FOR ENTERING AND LEAVING THE UPPER BUNK.
THE USE OF WATER OR SLEEP FLOTATION MATTRESSES IS PROHIBITED.
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE BUNK
BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS THE FULL
LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO PREVENT
ENTRAPMENT BETWEEN THE BED AND WALL (APPLICABLE FOR BUNK BEDS WITH
FULL LENGTH GUARDRAILS ON ONE SIDE).
PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL, LADDER AND OTHER
COMPONENTS ARE IN THEIR PROPER POSITION, FREE FROM DAMAGE, AND THAT ALL
CONNECTORS ARE TIGHT.
DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE
BED.
DO NOT USE SUBSTITUTE PARTS. CONTACT CUSTOMER SERVICE FOR REPLACEMENT
PARTS.
USE OF A NIGHT LIGHT MAY PROVIDE ADDED SAFETY PRECAUTION FOR A CHILD
USING THE UPPER BUNK.

*
*
*
*
*
*
*
*
*
*
Check bolts/screws periodically and tighten them if necessary.
PROHIBIT MORE THAN ONE PERSON ON UPPER BUNK.
KEEP THESE INSTRUCTIONS FOR FUTURE USE.
NOTES
PHILLIPS SCREWDRIVER (NOT INCLUDED) IS REQUIRED.
A RUBBER MALLET (NOT INCLUDED) IS RECOMMENDED TO FACILITATE ASSEMBLY.
READ EACH STEP CAREFULLY BEFORE STARTING. IT IS VERY IMPORTANT THAT EACH
STEP OF INSTRUCTION IS PERFORMED IN THE CORRECT ORDER. IF THESE STEPS ARE
NOT FOLLOWED IN SEQUENCE, ASSEMBLY DIFFICULTIES WILL OCCUR AND CAN
RESULT IN INJURY.
CAUTION: ADULT ASSEMBLY REQUIRED
ASSEMBLY WILL REQUIRE TWO PEOPLE.
MOST BOARD PARTS ARE LABELLED OR STAMPED ON THE RAW EDGE.
MAKE SURE ALL PARTS ARE INCLUDED. WORK IN SPACIOUS AREA, PREFERABLY ON A
SMOOTH SOFT SURFACE.
WARNING: Should this product
become damaged, and/or components
are broken or missing, DO NOT
USE.
BED IS DESIGNED FOR CHILDREN RANGING FROM 6 YEARS OF AGE TO YOUNG
TEENAGERS.
Dust regularly with a soft, dry cloth. We do not recommend the use of chemical cleaners or wax on
our lacquered furniture as it may damage the finish. Keep solvents, alcohol, nail polish and polish
removers away from your hardwood furniture surfaces.
MAINTENANCE
DOREL LIMITED WARRANTY
DOREL HOME FURNISHINGS CANADA warrants its product to be free from defects in material
and workmanship and agrees to remedy any such defect. This warranty covers 1 year from the date of
original purchase. This warranty is valid only upon presentation of proof of purchase. This is solely
limited to the repair or replacement of defective furniture components and no assembly labor is
included. This warranty does not apply to any product which has been improperly assembled,
subjected to misuse or abuse or which has been altered or repaired in any way. This warranty gives
you specific legal rights and you may also have other rights which vary from Province to Province.
CARE AND CLEANING

BUNK BED
WM3797W

BUNK BED
WM3797W

BUNK BED
WM3797W

NOTE: Headboard top cross (F) and headboard bottom cross (G) may require that they be pulled closer
together or further apart in order to allow wood dowels (7) to align with holes in top posts (A and B).
BUNK BED
WM3797W
One of the headboard top crosses (F) has a label on it, do not use it in this step.
Insert stoppers (10) and top headboard slats (S) into the headboard bottom cross (G) and push down until
firmly in place. Slide the headboard top cross (F) onto the top headboard slats (S). Insert wood dowels (7) into
ends of headboard top cross (F) and headboard bottom cross (G).
Attach top posts (A and B) using wood joint connectors (3) as shown.
STEP 1

STEP 2
BUNK BED
WM3797W
NOTE: Be sure to use headboard top cross (F) with label attached to it between top posts (A) and (C).
See illustration for label orientation.
Repeat the previous step to assemble the remaining three sets of headboards. Be sure to pair the bottom posts
(D) and (E) for one pair; (E) and (D) for another; and the top posts (C) and (A) for the last pair.

BUNK BED
WM3797W
Attach the two headboards with bottom posts (D and E) to bottom side rails (I and K) using joint connectors (1)
and barrel nuts (8) as shown.
NOTE: This is the lower bunk.
STEP 3
I
K
Holes
1
1
9
8
8
8
8
I
K
Holes
1
1
9
8
8
8
8

STEP 4
BUNK BED
WM3797W
Insert a wood dowel (7) into each end of the long guardrails (M). Attach two long guardrails (M) and two
top side rails (H and J) to top posts (A and B) & (A and C) as shown. Fasten top side rails (H and J) with
joint connectors (1) and barrel nuts (8). Fasten long guardrails (M) with wood joint connectors (3) .
Use Allen key (9) to tighten all joint connectors.
NOTE: This is the upper bunk.
3
M
3
M
3
M

STEP 5
Insert two slats (T) into the center slots of the bottom side rails (I and K) of the bottom bunk as shown.
NOTE: Once inserted, there should be three empty spaces left on each side.
BUNK BED
WM3797W

STEP 6
NOTE:If you notice that any slats (L) are not perfectly flat, be sure to assemble them so that slat (L) curves
up in the middle and down at the ends.
Insert slats (L) into remaining holes on the bottom side rails (I and K) on the lower bunk.
Secure slats (L) to the bottom side rails (I and K) with flat head wood screws (4) using a Phillips head
screw driver (not included).
Repeat step 5 and 6 to attach slats (T and L) to the upper bunk.
BUNK BED
WM3797W
NOTE: Slats (T and L) will be placed between two wooden blocks.

STEP 7
Insert wood dowels (7) in the ends of short guardrails (N). Attach short guardrails (N) to top post (A) with
wood joint connectors (3). Attach the guardrail leg (R) to the short guardrails (N) and top side rail (H) with
flat head wood screws (5).
Attach the other guardrail leg (R) to long guard rails (M) and top side rail (J) with flat head wood screws (5).
Use a Phillips head screwdriver (not included) to install screws (5).
BUNK BED
WM3797W
Place four wood dowels (6) into the holes in the bottom posts (D and E). Stack the top bunk onto the bottom
bunk with the help of another person.
5
5
7
3
R
R
N
M
K
J
I
H
C
B
A
6
6
5
5
7
3
R
R
N
M
K
J
I
H
C
B
A
6
6
5
5
7
3
R
R
N
M
K
J
I
H
C
B
A
6
6

STEP 8
BUNK BED
WM3797W
To assemble the ladder, insert wood dowels (7) into the end of the ladder steps (Q). Attach long ladder end
(O) and short ladder end (P) to ladder steps (Q) with wood joint connectors (2) and Allen key (9).
8 PCS
2
78 PCS

STEP 9
BUNK BED
WM3797W
Attach the ladder to the short guardrails (N), the top side rail (H) and bottom side rail (I) with wood joint
connectors (2) as shown.
NOTE:If slat (L) is covering the ladder mounting holes, remove slat (L) and replace after the ladder is
attached.
Slats are not shown in
illustration for clarity
N
H
I
26PCS
2

With the help of another person, remove the top bunk from the lower bunk.
NOTE: Switching the headboards will allow the two single beds to be identical (the headboards will have
taller posts and the footboards will have the shorter posts).
CONVERTING THE BUNK BED INTO TWO SINGLE BEDS
WM3797W
Remove the ladder and all the guardrails.
Disassemble the side rails from all headboards (top and lower bunks).
Re-assemble the headboards (with tall posts) and footboards (with short posts) to side rails.

CAUTION: This unit is intended for use only with the products
and/or maximum weights indicated. Use with other products and/or products
heavier than the maximum weights indicated may result in instability or cause
possible injury.
BUNK BED
WM3797W
USE ONLY COIL SPRING
MATTRESSES ON BOTH
THE UPPER AND LOWER
BUNKS. FAILURE TO DO
SO CAN RESULT IN
INJURY.
USE ONLY MATTRESSES WHICH
ARE 74"-75" LONG AND 37 1/2" -38
1/2" WIDE ON UPPER AND ON
LOWER BUNKS. ENSURE
THICKNESS OF MATTRESS DOES
NOT EXCEED 6".
DO NOT ALLOW CHILDREN
UNDER 6 YEARS OF AGE TO
USE THE UPPER BUNK.
BED IS DESIGNED FOR
CHILDREN RANGING FROM
6 YEARS OF AGE TO
YOUNG TEENAGERS.
DO NOT ALLOW HORSEPLAY ON OR
UNDER THE BED AND PROHIBIT
JUMPING ON THE BED.
MAXIMUM WEIGHT
CAPACITY:165 LBS
(75 KGS) PER LEVEL.
DO NOT RETURN PRODUCT TOTHE STORE.
If a part is missing or damaged, contact our customer service
department. We will replace the part FREE of charge.
Tel # : [phone]
E-Mail: [e-mail]
Fax #: [phone]

MODEL #: WM3797W
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE
PLEASE CONTACT CUSTOMER SERVICE REPRESENTATIVES AT THE FOLLOWING
NUMBERS SHOULD THERE BE ANY MISSING OR DEFECTIVE PART(S).
Request Date:
Name:
Shipping Address:
Street & Number:
City & Province:
Postal Code:
Day Time Phone Number:
(including area code)
Date & Place of Purchase:
Part(s) description and quantity: (Please be sure to list model number or SKU number)
Customer Service Representative Mailing Address:
Customer Service Department No. 413, 12345 Albert-Hudon Boulevard, Suite 100, Montreal, QC, Canada, H1G 3L1
Customer Service
Customer Service Phone Number 1-800-295-1980
Email: [email protected]
Customer Service Fax Number 514-353-7819